journal article·2017-09-21Open access

Surface Modification of Ti6Al4V Alloy by Pulsed Lasers: Microstructure and Hydrophobic Behavior

Milton Sérgio Fernandes de Lima, Ivan Almeida

Materials Research· Volume 20· Issue suppl 1

Abstract

In many aerospace applications, it is important to produce hydro-repellent surfaces because water and ice accumulation could lead to malfunctioning of the part or component with a potential critical failure. In this study, it was investigated the texturing of a titanium alloy (Ti6Al4V) by applying a pulsed Nd:YAG laser, aimed at the surface characterization by microscopy, X-ray diffraction, roughness and nano-indentation tests as well as free fall drop test. The experimental procedure aimed to understand the influence of three variables: (N) the number of laser runs 1, 2, 5 and 10; (V) laser speeds of 25, 50 and 100 cm/s and (P) laser power of 5, 10 and 20 W on the microstructure and the hydrophobic behavior. The Vickers hardness and elastic modulus of laser processed surfaces were similar to the untreated surfaces. When the number of the laser runs (N) increased, a TiO phase amount increases as a result of increasing heat input. The measured roughnesses decreased with increasing P as a direct result of remelting. As the number of runs (N) increases the surface became more and more flat, consequently the overlapping runs induced polishing of the titanium surfaces. The mean roughness Ra attained 0.23 µm after 10 runs at V=100m/s and P=10W, compared to Ra=0.41 µm of the virgin surface. The water repellent conditions were N1V50P05, N1V100P05, N2V25P05, N2V50P05, N5V25P05, N5V50P05, N5V100P10 and N10V25P10. These conditions were associated with a homogeneous remelted layer, low power, partial superposition of the laser shots of 50% or 75%, and a surface finish slightly rougher than the original material.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Diamond and Carbon-based Materials Research · Metal and Thin Film Mechanics · Laser Material Processing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Instituto de Estudos Avançados, Brazil

References (17)

Show source-provided references
1. Gna Na Muthu DS · 1979 · 177
2. Laser texturing for low-flying-height media10.1063/1.347908 ↗
3. A new laser texturing technique for high performance magnetic disk drives10.1109/20.490199 ↗
4. Efficiency of the laser texturing on the adhesion of the coated twist drills10.1016/j.jmatprotec.2006.03.068 ↗
5. Microstructural analyses and wear behavior of the cemented carbide tools after laser surface treatment and PVD coating10.1016/j.apsusc.2013.06.033 ↗
6. Laser Processing of Carbon Fiber Reinforced Polymer Composite for Optical Fiber Guidelines10.1016/j.phpro.2013.03.118 ↗
7. Influence of laser surface texturing on surface microstructure and mechanical properties of adhesive joined steel sheets10.1179/026708408X336364 ↗
8. Effect of surface finish on the osseointegration of laser-treated titanium alloy implants10.1016/j.biomaterials.2003.11.002 ↗
9. Anti-icing Potential of Superhydrophobic Ti6Al4V Surfaces: Ice Nucleation and Growth10.1021/acs.langmuir.5b02946 ↗
10. Li M · 2005
11. Wetting behaviour of laser synthetic surface microtextures on Ti-6Al-4V for bioapplication10.1098/rsta.2010.0003 ↗
12. Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology10.1557/jmr.2004.19.1.3 ↗
13. Studies at phase interfaces. I. The sliding of liquid drops on solid surfaces and a theory for spray retention10.1016/0095-8522(62)90011-9 ↗
14. Pulsed laser polishing of micro-milled Ti6Al4V samples10.1016/j.jmapro.2009.10.001 ↗
15. Phase transformations during laser processing of aerospace metallic materials10.4028/www.scientific.net/AMR.1135.179 ↗
16. Pederson R · 2002
17. Vickers hardness of cast commercially pure titanium and Ti-6Al-4V alloy submitted to heat treatments10.1590/S0103-64402006000200008 ↗