The use of ECAP in the Microstructural Conditioning of the 355 Aluminum Alloy for Thixoforming*
Source abstract
Abstract
The purpose of this study is to analyze the use plastic deformation (ECAP - Equal Channel Angular Pressing) in the preparation of the 355 aluminum for posterior use in Thixoforming. For this purpose, the 355 alloy, in the as cast state and after a pass of ECAP was heated to temperatures of 575 and 595 °C, enough to produce 45 and 55% of liquid fraction, for times of 0, 30, 60 e 90s. In these conditions, it is possible to obtain a refined globular structure with the size of a grain, close to 75 µm, globule size of 55 µm and high sphericity (around 0.66), parameters which are excellent for this kind of processing. Hot compression tests at the same temperatures and holding times determine the rheological behavior. Maximum processing strain was obtained around 1 MPa for the sample in ECAped condition against 4 MPa of the as cast condition, which corresponds to maximum viscosity around 105 Pa.s, (molten glass, clay), inferior to the as cast condition (11.5 * 105 Pa.s). Therefore, the ECAPed 355 alloy is an easily conformable material very likely to be applied to semisolid processing.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Universidade Estadual de Campinas, Brasil
Instituto Federal de Educação Ciência e Tecnologia de São Paulo, Brasil
References (19)
Show source-provided references
1. Rheocasting10.1016/0025-5416(76)90057-4 ↗
2. Behavior of metal alloys in the semisolid state10.1007/BF02661090 ↗
3. Modelling the semisolid processing of metallic alloys10.1016/j.pmatsci.2004.04.003 ↗
4. The implication of rheology in semisolid metal processes: an overview10.1016/j.jmatprotec.2006.08.003 ↗
5. Alloys for semisolid processing10.1016/B978-0-08-096532-1.00520-3 ↗
6. Analysis of the thermodynamic behavior of A355 and B319 alloys using the differentiation method10.1016/j.tca.2017.11.011 ↗
7. Thixoformability analysis of 355 aluminum alloy10.1007/s13632-017-0411-4 ↗
8. Comparative characterization of near-equiaxed microstructures as produced by spray casting, magneto hydrodynamic casting and the stress induced, melt activated process10.1016/S0921-5093(00)00907-2 ↗
9. Contribution to the study of mechanisms involved in the formation of rheocast structure10.1016/S0924-0136(00)00798-6 ↗
10. Primary and wrought products for semisolid forming of aluminium alloys
11. Semisolid microstructure evolution during reheating of aluminum A356 alloy deformed severely by ECAP10.1016/j.jallcom.2007.11.010 ↗
12. Influence of the processing route on the microstructure of aluminum alloy A356 for thixoforming10.1016/j.matchar.2013.08.011 ↗
13. Thixoforming of an ECAPed aluminum A356 alloy: microstructure evolution, rheological behavior, and mechanical properties10.1007/s11661-016-3339-4 ↗
14. 2014
15. Macro- and microstructure analysis of SSM A356 produced by electromagnetic stirring10.1016/S0924-0136(01)01148-7 ↗
16. Deformation of semisolid Sn-15%Pb alloy10.1007/BF02655112 ↗
17. 2013
18. Thermomechanical processing of metal feedstock for semisolid forming: a review10.1007/s11663-018-1387-4 ↗
19. Effect of strain rate on macroscopic behavior in the compression forming of semisolid aluminum alloy10.1016/S0924-0136(98)00383-5 ↗