Recrystallization of a Ti-45Ni-5Cu cold-worked shape memory alloy characterized by thermoelectric power and electrical properties
Source abstract
Abstract
The recrystallization of a cold-worked shape memory alloy (SMA) without R-phase transition, i.e. the Ti-45.0Ni-5.0Cu (% at.), has been studied by thermoelectric power (TEP) technique and electrical resistivity change (Dρ) on several heat treated samples after cold working. This study was also supported by differential scanning calorimetry (DSC), transmission electron microscopy (TEM) and hardness Vickers (HV) measurements. Transformation temperatures show an increase with heat treatment temperature, while hysteresis decreases. Hardness values decrease with aging temperature for the same heat treatment time. No important changes were observed in electrical resistivity with heat treatment temperature, except at 300ºC. TEP results show an important increase with heat treatment temperature, and a linear relationship was found between hardness and thermoelectric power. With this correlation between TEP and microhardness it is possible to predict its mechanical response by knowing its TEP, so this correlation could be important for applications.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Shape Memory Alloy Transformations · Titanium Alloys Microstructure and Properties · Magnetic and transport properties of perovskites and related materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Instituto Potosino de Investigación Científica y Tecnológica, México
Instituto Potosino de Investigación Científica y Tecnológica, México; Universidad Autónoma de Nuevo León, México
Centro de Investigación en Materiales Avanzados, México
References (25)
Show source-provided references
1. Physical metallurgy of Ti-Ni-based shape memory alloys10.1016/j.pmatsci.2004.10.001 ↗
2. Thermomechanical transformation fatigue of TiNiCu SMA actuators under a corrosive environment. Part I: experimental results10.1016/j.ijfatigue.2009.04.012 ↗
3. Fabrication of Ti-Ni alloys for proportional control10.3233/JAE-2006-716 ↗
4. Heat treatments and thermomechanical cycling influences on the R-phase in Ti-Ni shape memory alloys10.1590/S1516-14392010000300008 ↗
5. The effect of copper alloying element on the corrosion characteristics of Ti-Ni and ternary Ni-Ti-Cu meltspun shape memory alloy ribbons in 0.9% NaCl solution10.1016/S1452-3981(23)13113-0 ↗
6. A TiNiCu thin film micropump made by magnetron co-sputtered method10.2320/matertrans.47.532 ↗
7. Behaviour of strain-resistivity coupled measurements of Ti-Ni-Cu wires during thermal cycling under constant stress10.1016/j.msea.2003.10.333 ↗
8. Araújo CJ · 2005 · 409
9. Effect of thermomechanical treatment on the sequence of phase transformations in TiNi base alloys10.1007/BF00802680 ↗
10. Influence of the recovery and recrystallization processes on the martensitic transformation of cold worked equiatomic Ti-Ni alloy10.1016/S0921-5093(03)00068-6 ↗
11. The effects of heat treatment on the recovery stresses of shape memory alloys10.1088/0964-1726/19/3/035021 ↗
12. Dynamic recovery and dynamic recrystallization of NiTi shape memory alloy under hot compression deformation10.1016/S1003-6326(13)62440-1 ↗
13. Investigation of the recovery and recrystallization processes of Ni50.9Ti49.1 shape memory wires using in situ electrical resistance measurement10.1016/j.msea.2012.04.106 ↗
14. Crystal-to-amorphous transformation of NiTi induced by cold rolling10.1557/JMR.1990.1414 ↗
15. Microstructural evolution kinetics after plastic deformation of equiatomic Ti-Ni alloy during isothermal annealings10.1016/S0921-5093(02)00085-0 ↗
16. Study of the stress-assisted two-way memory effect of a Ti-Ni-Cu alloy using resistivity and thermoelectric power techniques10.1016/S0921-5093(03)00328-9 ↗
17. Thermoelectric power applied to metallurgy: principle and recent applications10.3139/146.110198 ↗
18. Lopez-Cuéllar E · 59 67
19. The influence of temperature on the evolution of functional properties during pseudoelastic cycling of ultra fine grained NiTi10.1016/j.msea.2007.01.182 ↗
20. The effect of rapid solidification and grain size on the transformation temperatures of Cu-Al-Be melt spun alloys10.1016/j.matchar.2005.12.017 ↗
21. The effect of processing conditions and subsequent heat treatment on the transformation behavior of some rapidly solidified copper-base shape memory alloys10.1007/BF02644970 ↗
22. Investigation of some electrical properties of niti wires presenting the shape memory effect
23. Annealing of cold-worked equiatomic Ti-Ni alloy followed by DSC and TEP methods10.1051/jp4:2001814 ↗
24. Macroscopic constitutive law for SMA: application to structure analysis by FEM10.1016/j.msea.2006.01.104 ↗
25. Study of reorientation of martensite variants under stress in Ti-Ni-Cu by resistivity and by thermoelectric power techniques10.1051/jp4:2001816 ↗