Effect of LZSA Glass-Ceramic Addition on Pressureless Sintered Alumina. Part II: Mechanical Behavior
Source abstract
Abstract
This work aims to evaluate the influence of a Li2O-ZrO2-SiO2-Al2O3 (LZSA) glass-ceramic on the mechanical behavior of alumina. Composites were prepared from alumina with three different particle sizes and 7 to 21 vol% of an LZSA glass-ceramic composition (11.6Li2O-16.8ZrO2-68.2SiO2-3.4Al2O3,). Specimens were obtained by uniaxial pressing. The optimum sintering temperature and holding time were found to be different for each composite. Structural characterization (bulk density and crystalline phases); mechanical characterization (flexure strength, elastic modulus, fracture toughness, and fracture energy); and microstructural analyses were carried out. Fine-grained alumina-based composite containing 21 vol% of glass-ceramic (1470 ºC and 3 h holding time, 2.0% porosity) showed a fracture toughness of 4.93 MPa·m0.5, an elastic modulus of 210 GPa, a fracture energy of 57 J·m-2, and a flexural strength of 170 MPa, in very good agreement with values reported by the literature. An increase of 37-177% in the fracture energy due to 21 vol% LZSA addition in the alumina was achieved for the range of grain size obtained in this work. Even though the final composition included a glassy component, the observed mechanical properties confirmed the effectiveness of the crystalline phases that were formed from LZSA glass-ceramic in reducing the propagation of cracks. The results showed that the addition of the LZSA glass-ceramic improved the mechanical properties of alumina.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced ceramic materials synthesis · Recycling and utilization of industrial and municipal waste in materials production · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Universidade do Extremo Sul Catarinense - UNESC, BR
References (37)
Show source-provided references
1. Wear-resistant engineering ceramics10.1016/S0043-1648(01)00820-1 ↗
2. Erosion characteristics of alumina ceramics at high temperatures10.1016/0043-1648(94)07047-4 ↗
3. Erosion of alumina ceramics by air- and water-suspended garnet particles10.1016/S0043-1648(00)00335-5 ↗
4. Influence factors on wear resistance of two alumina matrix composites10.1016/j.wear.2007.08.011 ↗
5. Wear resistance of Al2O3-CNT ceramic nanocomposites at room and high temperatures10.1016/j.ceramint.2012.12.100 ↗
6. Fracture thoughness of alumina-zirconia composites10.1016/j.ceramint.2005.02.012 ↗
7. Alumina-mullite ceramics for structural applications10.1016/j.ceramint.2005.04.001 ↗
8. Alumina-Based Ceramics for Armor Application Mechanical Characterization and Ballistic Testing10.1155/2014/618154 ↗
9. Wear behaviour of alumina based ceramic cutting tools on machining steels10.1016/j.triboint.2005.01.021 ↗
10. Grain-Size and R-Curve Effects in the Abrasive Wear of Alumina10.1111/j.1151-2916.1989.tb09718.x ↗
11. Grain size effect on abrasive wear mechanisms in alumina ceramics10.1016/0043-1648(93)90508-J ↗
12. Grain size effects on the wet erosive wear of high-purity polycrystalline alumina10.1016/0043-1648(94)90297-6 ↗
13. Grain-size dependence of the wear of alumina10.1016/0043-1648(95)07171-7 ↗
14. Wet erosion of liquid phase sintered alumina10.1016/S0043-1648(99)00236-7 ↗
15. Processing of High-Density Submicrometer Al2O3 for New Applications10.1111/j.1151-2916.2003.tb03339.x ↗
16. Improved sliding wear-resistance of alumina with sub-micron grain size A comparison with coarser grained material10.1016/j.jeurceramsoc.2007.02.205 ↗
17. Effect of niobium doping on the densification and grain growth in alumina10.1016/j.ceramint.2007.02.010 ↗
18. Liquid-phase sintering of alumina with YSiAlON oxynitride glass10.1016/S0167-577X(03)00119-8 ↗
19. Effect of a LZSA glass-ceramic addition on the sintering behavior of alumina10.1007/s10973-015-5144-5 ↗
20. Low thermal expansion sintered LZSA glass-ceramics
21. Sintering behavior of LZSA glass-ceramics10.1590/S1516-14392009000200014 ↗
22. Sintering kinetics of a 18 8Li2O 8.3ZrO2 64.2SiO2 8.7Al2O3 glass ceramic10.1016/j.ceramint.2011.03.047 ↗
23. Relationship between Surface Abrasion Wear and Brightness in Glazed Porcelainized Stoneware Tiles
24. Crystallisation Kinetics of a ß-Spodumene-Based Glass Ceramic
25. Effect of LZSA Glass-Ceramic Addition on the Pressureless Sintered Alumina Part I: Grain Growth10.1590/1980-5373-mr-2016-0964 ↗
26. Grain boundary and testing procedure, a new approach to the tribology of alumina materials10.1016/S0043-1648(07)00133-0 ↗
27. Evaluated Material Properties for a Sintered alpha-Alumina10.1111/j.1151-2916.1997.tb03074.x ↗
28. Effective fracture toughness in Al2O3-Al2O3/ZrO2 laminates10.1016/j.jeurceramsoc.2006.04.063 ↗
29. Marques CM · 2006
30. The mechanical performance of alumina as a function of grain size10.1016/0254-0584(94)90037-X ↗
31. Mechanical Properties of Some Commercial Alumina Ceramics
32. Role of wollastonite additive on density, microstructure and mechanical properties of alumina10.1016/S0272-8842(03)00029-4 ↗
33. Role of fabrication route and sintering on wear and mechanical properties of liquid-phase-sintered alumina10.1016/S0272-8842(00)00022-5 ↗
34. Influence of composition on mechanical behaviour of porcelain tile Part III: Effect of the cooling rate of the firing cycle10.1016/j.msea.2010.12.086 ↗
35. Influence of powder, chemistry and intergranular phases on the wear resistance of liquid-phase-sintered Al2O310.1016/S0043-1648(00)00407-5 ↗
36. Microstructure dependent hardness and fracture behavior in liquid-phase-sintered Al2O310.1016/S0272-8842(99)00070-X ↗
37. Impurity-Dependent Morphology and Grain Growth in Liquid-Phase-Sintered Alumina10.1111/j.1151-2916.2001.tb00886.x ↗