Microstructure and Mechanical Properties of a Multiphase 17%Cr Stainless Steel
Source abstract
Abstract
The mechanical Properties of an experimental 17%Cr multiphase alloy were studied as function of heat treatment parameters. Containing majoritary ferrite and martensite, this type of steel is applied in tubullars and casings in the off shore oil and gas production, where high corrosion and mechanical resistance are required. Quenching and tempering heat treatments produced different combinations of ferrite, martensite, austenite and precipitates. The as quenched material has 35% of ferrite, martensite and 3.8% of retained austenite. The material quenched and tempered at 500oC has lower austenite (1.2%), and tempered martensite with Nb carbides. The tensile properties were excellent, but the low temperature (-46oC) impact toughness was very small. A high toughness was obtained in the material quenched and tempered at 650oC, with a microstructure of ferrite, tempered martensite and 7.2% of reversed austenite, but the mechanical resistance was under 621 Mpa (90ksi), which is considered too low for the application envisioned. The material tempered at 600oC showed an interesting combination of mechanical resistance and low temperature toughness. The flow stress curves of the material were modelled by Hollomon’s equation and Voce’s equation with correlation coefficients (R2) higher than 0.98.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Microstructure and Mechanical Properties of Steels · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Universidade Federal Fluminense, Brasil; Universidade Federal Fluminense, Brasil
Universidade Federal Fluminense, Brasil; Instituto Federal do Rio de Janeiro, Brasil
Universidade Federal Fluminensee, Brasil
References (20)
Show source-provided references
1. Modelling of hydrogen diffusion and hydrogen induced cracking in supermartensitic and duplex stainless steels10.1016/j.matdes.2008.04.026 ↗
2. Recent developments on martensitic stainless steels for oil and gas production
3. Davis JR · 1994
4. Kimura M · 2005
5. High Cr stainless steel OCTG with high strength and superior corrosion resistance
6. Influence of microstructure in the hydrogen permeation in martensitic-ferritic stainless steel10.1016/j.ijhydene.2015.06.102 ↗
7. DL-EPR and AFM study of sensitization of a 17%Cr multiphase stainless steel10.1002/maco.202112814 ↗
8. Influence of tempering treatment on microstructure and pitting corrosion resistance of a new super ferritic–martensitic–austenitic stainless steels with 17%Cr10.1080/1478422X.2015.1110418 ↗
9. Slow strain rate tensile test results of new multiphase 17%Cr stainless steel under hydrogen cathodic charging10.1016/j.ijhydene.2015.05.148 ↗
10. 2022
11. 2018
12. 2020
13. Improvement of slurry erosion resistance of martensite/ferrite duplex stainless steel by hot rolling10.1007/s12540-010-0013-z ↗
14. Influence of heat treatments on toughness and sensitization of a Ti-alloyed supermartensitic stainless steel10.1007/s10853-011-5753-8 ↗
15. Influence of tempering on microstructure and mechanical properties of Ti alloyed 13%Cr supermartensitic stainless steel10.1179/1743284713Y.0000000448 ↗
16. Effects of W substitution on the precipitation of secondary phases and the associated pitting corrosion in hyper duplex stainless steels10.1016/j.jallcom.2012.07.129 ↗
17. 2015
18. Tensile deformation
19. Ludwik P · 1909
20. The relationship between stress and strain for homogeneous deformation