journal article·2024Open access

Wear Behavior of Ti-xNb Biomedical Alloys by Ball Cratering

Felype N. de Mattos, Pedro A. B. Kuroda, Mariana C. Rossi, Conrado R. M. Afonso

Materials Research· Volume 27

Abstract

Ti alloys have been developing through the years, aiming the biomedical application since it has suitable properties. Among Ti alloys, the Ti-Nb systems are a pronounced group to biomedical applications due to its low elastic modulus, good corrosion resistance, and mechanical properties. Although this system is quite well-known regarding its phases, structure and properties, there is not plenty of information about wear available in the literature. To investigate the wear resistance, the samples were submitted to x-ray diffraction (XRD) and scanning electron microscopy (SEM) to analyze the phases formed. Hardness and elastic modulus were measured by microhardness Vickers and dynamic Young modulus by excitation impulse. Additionally, wear volume, wear resistance, and H/E ratio were calculated to understand the wear material’s performance. This study aims to investigate the wear resistance of Ti-xNb (x = 15, 25 and 40wt.%), one of each type of Ti alloys and phases formed: Ti-15Nb (α´), Ti-25Nb (α”) and Ti-40Nb (β) and the influence of cooling rate after solution heat treatment on wear properties through ball cratering. It was possible to find that the harder the alloy, the higher the wear resistance. Thus, in the case of Ti-xNb (x = 15, 25 and 40wt.%), alloys the hardness plays a significant role in wear resistance. Besides that, the samples that have presented the α´ or α”phase have the lowest wear resistance. Therefore, not only the hardness influences the wear resistance but also the combination of phases formed.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Metal and Thin Film Mechanics · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Universidade Federal de São Carlos, Brasil

References (34)

Show source-provided references
1. From porous to dense nanostructured β-Ti alloys through high-pressure torsion10.1038/s41598-017-13074-z ↗
2. Powder metallurgical processing of low modulus β-type Ti-45Nb to bulk and macro-porous compacts10.1016/j.powtec.2017.09.015 ↗
3. Corrosion and wear behavior of Ti-5Cu-xNb biomedical alloy in simulated body fluid for dental implant applications10.1016/j.jmbbm.2022.105533 ↗
4. Effect of thermomechanical treatments on microstructure, phase composition, vickers microhardness, and Young’s modulus of Ti-xNb-5Mo alloys for biomedical applications10.3390/met12050788 ↗
5. Effect of thermomechanical treatments on the phases, microstructure, microhardness and Young’s modulus of Ti-25Ta-Zr alloys10.3390/ma12193210 ↗
6. Surface characterization of new β Ti-25Ta-Zr-Nb alloys modified by micro-arc oxidation10.3390/ma16062352 ↗
7. Severe plastic deformation and different surface treatments on the biocompatible Ti13Nb13Zr and Ti35Nb7Zr5Ta alloys: microstructural and phase evolutions, mechanical properties, and bioactivity analysis
8. Structure - property relationship of cast Ti-Nb alloys10.1046/j.1365-2842.2002.00825.x ↗
9. Influence of Nb content on the structure, morphology, nanostructure, and properties of Titanium-Niobium Magnetron sputter deposited coatings for biomedical applications10.1016/j.surfcoat.2017.03.015 ↗
10. Continuous cooling transformation (CCT) diagrams of β Ti-40Nb and TMZF alloys and influence of cooling rate on microstructure and elastic modulus
11. Influence of swaging on microstructure, elastic modulus and vickers microhardness of β Ti-40Nb Alloy for implants10.1007/s11665-021-05706-3 ↗
12. Composition/phase structure and properties of titanium-niobium alloys10.2320/matertrans.44.2384 ↗
13. Microstructure and lattice parameters of suction-cast Ti - Nb alloys in a wide range of Nb concentrations10.1016/j.msea.2021.141378 ↗
14. Preparation, structural, microstructural, mechanical, and cytotoxic characterization of Ti-15Nb alloy for biomedical applications10.1111/aor.13624 ↗
15. Current advances in enhancement of wear and corrosion resistance of titanium alloys: a review10.1080/10667857.2016.1212780 ↗
16. Dry sliding wear behaviour of β-type Ti-Nb and Ti-Mo surfaces designed by diffusion treatments for biomedical applications10.1016/j.jmbbm.2018.12.029 ↗
17. Tribocorrosion behavior of β -type Ti-Nb-Ga alloys in a physiological solution10.1016/j.triboint.2023.108325 ↗
18. The comparison of wear performances of CP-Ti, Ti6Al4V, Ti45Nb alloys oxidized by anodic oxidation under ambient air and vacuum conditions
19. Assessment of improved tribocorrosion in novel in-situ Ti and β Ti - 40Nb alloy matrix composites produced with NbC addition during arc-melting for biomedical applications
20. 2017
21. Assessment of β stabilizers additions on microstructure and properties of as-cast β Ti-Nb based alloys10.1016/j.jmrt.2022.12.144 ↗
22. Assessment of improved tribocorrosion in novel in-situ Ti and β Ti-40Nb alloy matrix composites produced with NbC addition during arc-melting for biomedical applications
23. Atomic-scale investigations of passive film formation on Ti-Nb alloys10.1016/j.apsusc.2022.156282 ↗
24. Zero thermal expansion and high Young’s modulus in Ti-Nb achieved by concurrent α″iso and ω precipitation10.1016/j.scriptamat.2023.115477 ↗
25. Enhanced structural and tribological performance of nanostructured Ti-15Nb alloy for biomedical applications10.1016/j.rinp.2019.102767 ↗
26. The structure and mechanical properties of as-cast Ti-25Nb-xSn alloys for biomedical applications10.1016/j.msea.2013.01.002 ↗
27. Plasma electrolytic oxidation of Ti-25Nb-xTa alloys in solution containing Ca and P ions
28. Design and processing of near- b Ti e Nb e Ag alloy with low elastic modulus and enhanced corrosion resistance for orthopedic implants10.1016/j.jmrt.2023.03.003 ↗
29. Microstructure and beta grain growth behavior of Ti-Mo alloys solution treated
30. On the role of internal stresses on the superelastic behaviour of Ti-24Nb (at.%)10.1016/j.actamat.2022.118161 ↗
31. Wear characteristics of Ti-Nb-Ta-Zr and Ti-6Al-4V alloys for biomedical applications10.1016/j.wear.2004.04.001 ↗
32. Effects of niobium particles on the wear behavior of powder metallurgical γ- TiAl alloy in different environments
33. On the significance of the H/E ratio in wear control: a nanocomposite coating approach to optimised tribological behaviour10.1016/S0043-1648(00)00488-9 ↗
34. Impact of rare earth elements on nanohardness and nanowear properties of beta-type Ti-24Nb-38Zr-2Mo alloy for medical applications10.1016/j.mtla.2020.100772 ↗