Microstructure and Corrosion Behavior of Ni-Cr-Mo Nickel-based Alloy Weld
Source abstract
Abstract
The mechanical properties and corrosion performance of the N10276 alloy welded joint were investigated with nano-hardness testing and electrochemical measurement. The results showed that solidification mode changes from equiaxed crystal to columnar crystal from the center of the weldment to the fusion zone. With the increase of immersion times, the diameter of capacitance arc and the impedance modulus increase, and the corrosion resistance of HAZ decreases. The strengthening effect of welded metal was more obvious than that of heat affected zone for the nickel-based welded joint and especially in coarse grained heat affected zone, the hardening resulted from overheating was not apparent. Nickel-based weld metal with high content of alloying elements were often segregated at interdendritic regions or precipitated in grain interior under nonequilibrium solidification, which differ from conventional low alloy steel welded joint.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Nanjing Institute of Technology, China; Jiangsu Key Laboratory of Advanced Structural Materials and Application Technology, China
Shandong Jianzhu University, China
References (31)
Show source-provided references
1. Microstructure and hardness studies of the electron beam welded zone of Hastelloy C-27610.1016/j.jallcom.2004.08.031 ↗
2. Mechanical properties anisotropy of cold-rolled and solution-annealed Ni-based Hastelloy C-276 alloy10.1007/s11661-014-2294-1 ↗
3. Effects of temperature and strain rate on tensile deformation behavior of superalloy UNS N1027610.1016/j.msea.2017.05.085 ↗
4. Corrosion behaviour of WC hardmetals with nickel-based binders10.1016/j.corsci.2018.11.015 ↗
5. Microstructure and wear resistance of laser cladded composite coatings prepared from pre-alloyed WC-NiCrMo powder with different laser spots10.1016/j.optlastec.2017.12.007 ↗
6. Hot deformation characteristics and processing map of nickel-based C276 superalloy10.1016/j.jallcom.2014.10.118 ↗
7. Effect of low energy laser shock peening on the mechanical integrity of Hastelloy C-276 welds
8. Hot deformation characteristics and microstructure evolution of Hastelloy C-27610.1016/j.msea.2017.11.056 ↗
9. Effect of post-weld heat treatment on the tensile strength of laser beam welded Hastelloy C-276 sheets at different heat inputs10.1016/j.jmapro.2018.12.019 ↗
10. Hot deformation characteristics and forging process of corrosion resistant nickel-base C-276 alloy10.1016/j.proeng.2011.12.548 ↗
11. Thermal stability of hastelloy alloy C-27610.5006/0010-9312-25.5.222 ↗
12. Cavitation erosion behavior of Hastelloy C-276 nickel-based alloy10.1016/j.jallcom.2014.08.248 ↗
13. Damage mechanism of cavitation erosion in austenite→martensite phase transformable Fe-Cr-C-Mn/Ni alloys10.1016/j.wear.2013.12.015 ↗
14. Cavitation-erosion of 3Y-TZPs obtained at different sintering temperatures10.1016/j.wear.2013.01.104 ↗
15. Correlation of martensitic transformation and surface mechanical behavior with cavitation erosion resistance for some iron-based alloys10.1016/j.wear.2003.10.008 ↗
16. Evolution of microstructure and tensile properties during solution treatment of nickel-based UNS N10276 alloy10.1016/j.msea.2017.08.101 ↗
17. On the prediction of effect of direction of welding on bead geometry and residual deformation of double-sided fillet welds10.1007/s13296-016-6007-z ↗
18. Experimental and numerical study on effect of weld reinforcement on angular distortion of SAW square butt welded plates10.5781/JWJ.2018.36.2.8 ↗
19. Investigation on microstructure, micro segregation and mechanical properties of ATIG welded Alloy C-27610.1016/j.matpr.2017.11.327 ↗
20. Corrosion behavior of Hastelloy C-276 in supercritical water10.1016/j.corsci.2009.05.041 ↗
21. Microstructure analysis of stress rupture performance of hastelloy C-276 alloy at 650 °C
22. Microstructural evolution in nickel alloy C-276 after Ar + ion irradiation10.1016/j.nimb.2010.12.004 ↗
23. Continuous stiffness measurement during instrumented indentation testing10.1111/j.1747-1567.2010.00618.x ↗
24. Effect of groove design and post-weld heat treatment on microstructure and mechanical properties of P91 steel weld10.1007/s11665-016-2127-z ↗
25. Characterization of microstructure of HAZs in as-welded and service condition of P91 pipe weldments10.1007/s12540-017-6394-5 ↗
26. Effect of surface nanocystallization induced by fast multiple rotation rolling on hardness and corrosion behavior of 316L stainless steel10.1016/j.apsusc.2011.02.127 ↗
27. Characterization of roughness and pitting corrosion of surfaces modified by blasting and thermal oxidation10.1016/j.surfcoat.2010.04.051 ↗
28. Analysis of the corrosion behavior of an A-TIG welded SS 409 weld fusion zone10.1007/s11665-017-3022-y ↗
29. Effect of weld thermal cycle on metallurgical and corrosion behavior of friction stir weld joint of AA2014 aluminium alloy10.1016/j.jmapro.2018.12.001 ↗
30. In vitro corrosion study by EIS of a nickel-free stainless steel for orthopaedic applications10.1016/j.biomaterials.2004.03.012 ↗
31. The corrosion behaviour of austenitic and duplex stainless steels in artificial saliva with the addition of fluoride10.1016/j.corsci.2010.11.010 ↗