journal article·2025Open access

Metallurgical and Mechanical Examination of Fatigue-Induced Fracture in a Conveyor Drum Shaft

Anderson Luiz de Oliveira, Maria Veronica Goncalves Rodrigues, Jhonatan Peres de Sousa, João Carlos Ferreira, Isaac Araújo Furtado, Marcos Natan da Silva Lima, Antonio Enrique Salas Reyes, Eden Santos Silva, Hamilton Ferreira Gomes de Abreu, Gedeon Silva Reis, Samuel Filgueiras Rodrigues

Materials Research· Volume 28· Issue suppl 1

Abstract

This work investigates the fatigue failure mode of a shaft used in a conveyor system for mining applications through visual inspection, metallographic examination, fracture analysis, and mechanical testing. It was observed that a misalignment of about 5° between the shaft and the conveyor drum system promoted intensive contact with the parts. The combination of misalignment and overload was the leading cause of the localized plastic deformation, which resulted in the shaft fracture. A metallurgical examination revealed ferritic and pearlitic microstructures for an AISI 4140 grade steel. This suggested that the heat treatment on the steel was not adequate for the application. Therefore, it can be inferred that no preventive or corrective maintenance inspections were performed during the shaft's operational production period.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Mechanical Failure Analysis and Simulation · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Instituto Federal de Educação, Ciência e Tecnologia do Maranhão, Brasil; Universidade Federal do Piauí, Brasil; Instituto Federal de Educação, Ciência e Tecnologia do Tocantins, Brasil

Instituto Federal de Educação, Ciência e Tecnologia do Maranhão, Brasil; Universidade Federal do Piauí, Brasil

Instituto Federal de Educação, Ciência e Tecnologia do Maranhão, Brasil

Instituto Federal de Educação, Ciência e Tecnologia do Maranhão, Brasil; Universidade Federal do Ceará, Brasil

Instituto Federal de Educação, Ciência e Tecnologia do Maranhão, Brasil; Universidad Nacional Autónoma de México, México; Instituto Federal de Educação, Ciência e Tecnologia do Maranhão, Brasil

Instituto Federal de Educação, Ciência e Tecnologia do Maranhão, Brasil; Instituto Federal de Educação, Ciência e Tecnologia do Maranhão, Brasil

Universidade Federal do Ceará, Brasil

Instituto Federal de Educação, Ciência e Tecnologia do Maranhão, Brasil; Universidade Federal do Piauí, Brasil; Universidade Federal do Ceará, Brasil; Instituto Federal de Educação, Ciência e Tecnologia do Maranhão, Brasil

References (19)

Show source-provided references
1. 1997
2. 2021
3. Fatigue in the shell of a conveyor drum10.1016/j.engfailanal.2006.11.071 ↗
4. McHenry HI · 1980
5. Failure modes, mechanisms and causes of shafts in mechanical equipment
6. Failure of metals I: brittle and ductile fracture10.1016/j.actamat.2015.12.034 ↗
7. Failure analysis in metallic materials10.3390/met13081374 ↗
8. Fatigue failure analysis of a speed reduction shaft10.3390/met11060856 ↗
9. Experimental analysis of stress, strain and deformation on different types of conveyor belt pulleys. An analysis conducted at Visakhapatnam Steel Plant
10. Otai J · 2023
11. Failure analysis of the end of a shaft of an engine10.1016/j.engfailanal.2009.08.010 ↗
12. Effect of forging sequence and heat treatment on microstructure of high-duty power-plant shaft made of Cr-Mo ultra-high strength steel10.2298/JMMB221005026S ↗
13. Effect of single and double quenching-tempering heat treatments on microstructures and tensile strength of AISI 4140 in annealing condition10.1063/5.0115822 ↗
14. Effect of Ti microaddition on cavitation behavior during uniaxial hot-tensile of Fe-22Mn-1.5Al-1.3Si-0.5C austenitic TWIP steel10.1557/opl.2016.28 ↗
15. Hull D · 1999
16. Normalizing effect on fatigue crack propagation at the heat-affected zone of AISI 4140 steel shielded metal arc weldings10.1590/S1516-14392013005000047 ↗
17. Failure analysis of a hot forged SAE 4140 steel kingpin
18. A characterization for the flow behavior of 42CrMo steel10.1016/j.commatsci.2010.07.021 ↗
19. Improvement of low-cycle fatigue resistance in AISI 4140 steel by annealing treatment10.1016/j.ijfatigue.2019.04.020 ↗