Study on Mechanical Properties and Failure Mechanism of Medium Manganese TRIP Steel / DP590 Dissimilar Steel Resistance Spot Welding Joint
Source abstract
Abstract
This paper presents the resistance spot welding process test and numerical simulation analysis of medium manganese steel TRIP steel (7MnSteel) and DP590 steel plate. The results show that the failure mode is PF-TT failure, and IF and PF-TT are investigated. At the same time, based on the numerical simulation under the typical welding parameters, the welding plate has the stress concentration at the electrode edge at the beginning of the welding. Along with the welding, there is the stress concentration in the heat-affected zone of the medium manganese TRIP steel, which may also be the reason for the failure of the joint here. The current density is concentrated at the contact surface between the electrode and the weld plate, and the error in the diameter of the nugget measured by simulation and experiment is within 7%, which verifies the accuracy and reliability of the model.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Nanchang University, China; Jiangxi Provincial Key Laboratory of Robot and Welding Automation, China
References (30)
Show source-provided references
1. Investigation of mechanical properties of galvanized automotive sheets joined by resistance spot welding10.1007/s11665-012-0189-0 ↗
2. Ultrafine grained duplex structure developed by ART-annealing in cold rolled medium-Mn steels10.1016/S1006-706X(14)60032-7 ↗
3. Third generation of AHSS with increased fraction of retained austenite for the automotive industry10.1016/j.acme.2012.06.011 ↗
4. Development of 3rd generation AHSS with medium Mn content alloying compositions10.1016/j.msea.2012.11.113 ↗
5. Spectral TRIP enables ductile 1.1 GPa martensite10.1016/j.actamat.2016.03.070 ↗
6. Medium Mn transformation-induced plasticity steels: recent progress and challenges10.1016/j.scriptamat.2016.07.013 ↗
7. The effects of prior austenite grain boundaries and microstructural morphology on the impact toughness of intercritically annealed medium Mn steel10.1016/j.actamat.2016.09.048 ↗
8. The effects of the initial martensite microstructure on the microstructure and tensile properties of intercritically annealed Fe-9Mn-0.05 C steel10.1016/j.actamat.2014.07.005 ↗
9. Deformation behaviour of spot-welded high strength steels for automotive applications10.1016/j.msea.2010.07.091 ↗
10. Review of control systems for resistance spot welding: past and current practices and emerging trends10.1179/stw.1996.1.1.1 ↗
11. Combined effect of resistance spot welding and precipitation hardening on tensile shear load bearing capacity of A286 superalloy10.1016/j.msea.2017.02.015 ↗
12. Welding time effect on tensile-shear loading in resistance spot welding of SPA-H weathering steel sheets used in railway vehicles10.12693/APhysPolA.131.52 ↗
13. Microstructure and tensile-shear properties of resistance spot-welded medium Mn steel10.3390/met8010048 ↗
14. A comparison of cross-tension properties and fracture behavior between similar and dissimilar resistance spot-weldments in medium-Mn TRIP steel10.1016/j.msea.2019.03.023 ↗
15. A novel shim-assisted resistance spot welding process to improve weldability of medium-Mn transformation-induced plasticity steel10.1007/s11663-018-1463-9 ↗
16. Modeling and experimental research on resistance spot welded joints for dual-phase steel10.3390/ma12071108 ↗
17. The modeling and process analysis of resistance spot welding on galvanized steel sheets used in car body manufacturing10.1016/j.matdes.2011.06.064 ↗
18. Development of numerical analysis model for resistance spot welding of automotive steel10.1007/s12206-017-0634-y ↗
19. The finite element modeling of the resistance spot welding process
20. Analysis and development of a real time control methodology in resistance spot welding
21. Modeling of resistance spot weld nugget growth
22. Computer simulation of resistance spot welding in aluminum: part I
23. Weldability analysis of spot welding on aluminum using FEM
24. Modeling and numerical simulation of the resistance spot welding of zinc coated steel sheets using rounded tip electrode: analysis of required conditions10.1016/j.apm.2013.10.060 ↗
25. Subcritical heat affected zone softening in hot-stamped boron steel during resistance spot welding10.1016/j.matdes.2018.05.067 ↗
26. Overview of recent advances of process analysis and quality control in resistance spot welding10.1016/j.ymssp.2019.01.041 ↗
27. Effect of expulsion on peak load and energy absorption of low carbon steel resistance spot welds10.1179/174329307X249342 ↗
28. Critical review of automotive steels spot welding: process, structure and properties10.1179/1362171813Y.0000000120 ↗
29. Effect of weld nugget size on over load failure mode of resistance spot welds10.1179/174329307X164409 ↗
30. A novel shim-assisted resistance spot welding process to improve weldability of medium-mn transformation-induced plasticity steel10.1007/s11663-018-1463-9 ↗