journal article·2021Open access

3Y-TZP DLP Additive Manufacturing: Solvent-free Slurry Development and Characterization

Italo Leite de Camargo, Rogério Erbereli, Hayden Taylor, Carlos Alberto Fortulan

Materials Research· Volume 24· Issue 2

Abstract

Vat photopolymerization (VP) stands out among ceramic additive manufacturing processes for its ability to print sub-100 micrometer complex features. One of the main challenges of this process is the preparation of a homogeneous and stable ceramic slurry with a high solid load and low viscosity. In this work, different dispersants and resins were tested, aiming to provide a solvent-free slurry suitable for DLP additive manufacturing. Disperbyk-111 and PEGDA 250 stood out in the tests, providing a 40 vol% ceramic slurry with no noticeable sedimentation and viscosity of 2.3 Pa.s at 30 s-1 despite the relatively high specific surface area (15 m2/g) of the 3Y-TZP powder used compared to powders usually used for VP slurries. The adsorption of Disperbyk-111 on ceramic particles surface was investigated by FTIR. Finally, ceramic bodies were 3D printed, debound and sintered at 1500 ºC for 2 h, confirming the ability to manufacture detailed dense ceramic parts.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Photopolymerization techniques and applications · Injection Molding Process and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Universidade de São Paulo, Brasil; Instituto Federal de Educação, Brasil

Universidade de São Paulo, Brasil

University of California, USA

References (56)

Show source-provided references
1. Rheological and curing behavior of acrylate-based suspensions for the DLP 3D printing of complex zirconia parts10.3390/ma11122350 ↗
2. A review on the rheological behavior and formulations of ceramic suspensions for vat photopolymerization10.1016/j.ceramint.2021.01.031 ↗
3. Freeform fabrication of ceramics via stereolithography10.1111/j.1151-2916.1996.tb09022.x ↗
4. Photosensitive ZrO2 suspensions for stereolithography10.1016/j.ceramint.2019.03.123 ↗
5. Powder characteristics on the rheological performance of resin-based zirconia suspension for stereolithography
6. Digital light processing-stereolithography three-dimensional printing of yttria-stabilized zirconia10.1016/j.ceramint.2019.12.113 ↗
7. Research into the mechanical properties, sintering mechanism and microstructure evolution of Al2O3-ZrO2 composites fabricated by a stereolithography-based 3D printing method10.1016/j.matchemphys.2017.12.021 ↗
8. Additive Manufacturing of ceramic components by Digital Light Processing: a comparison between the “bottom-up” and the “top-down” approaches10.1016/j.jeurceramsoc.2019.01.044 ↗
9. Lithography-based ceramic manufacturing (LCM) – Viscosity and cleaning as two quality influencing steps in the process chain of printing green parts10.1016/j.jeurceramsoc.2017.05.046 ↗
10. Dispersion and stability of SiC ceramic slurry for stereolithography10.1016/j.ceramint.2019.10.203 ↗
11. Effect of the particle size and the debinding process on the density of alumina ceramics fabricated by 3D printing based on stereolithography10.1016/j.ceramint.2016.08.024 ↗
12. Additive manufacturing of ZrO2 ceramic dental bridges by stereolithography10.1108/RPJ-09-2016-0144 ↗
13. Preparation of a defect-free alumina cutting tool via additive manufacturing based on stereolithography: optimization of the drying and debinding processes10.1016/j.ceramint.2016.04.050 ↗
14. Fabrication of dense zirconia-toughened alumina ceramics through a stereolithography-based additive manufacturing10.1016/j.ceramint.2016.10.027 ↗
15. Additive manufacturing of silica ceramics from aqueous acrylamide based suspension10.1016/j.ceramint.2019.07.118 ↗
16. Development of a novel aqueous hydroxyapatite suspension for stereolithography applied to bone tissue engineering10.1016/j.ceramint.2018.11.063 ↗
17. Fabrication of piezoelectric nano-ceramics via stereolithography of low viscous and non-aqueous suspensions10.1016/j.jeurceramsoc.2019.10.033 ↗
18. Transparent inorganic/organic copolymers by the sol-gel process: thermal behavior of copolymers of tetraethyl orthosilicate (TEOS), vinyl triethoxysilane (VTES) and (meth)acrylate monomers10.1007/BF00487723 ↗
19. Influence of residual monomer on cracking in ceramics fabricated by stereolithography10.1111/j.1744-7402.2010.02578.x ↗
20. Concentrated suspension-based additive manufacturing: viscosity, packing density, and segregation10.1016/j.jeurceramsoc.2019.05.034 ↗
21. Influence of boundary masks on dimensions and surface roughness using segmented exposure in ceramic 3D printing10.1016/j.ceramint.2018.11.031 ↗
22. Effect of plasticizer on the fabrication and properties of alumina ceramic by stereolithography-based additive manufacturing10.1016/j.ceramint.2018.07.259 ↗
23. Additive manufactured 3Y-TZP ceramics: study of micromechanical behavior by nanoindentation and microscratch method10.1111/ijac.13459 ↗
24. Photocurable ceramic slurry using solid camphor as novel diluent for conventional digital light processing (DLP) process10.1016/j.jeurceramsoc.2019.05.069 ↗
25. Preparation of high solid loading and low viscosity ceramic slurries for photopolymerization-based 3D printing10.1016/j.ceramint.2019.03.024 ↗
26. The effect of the surfactants on the formulation of UV-curable SLA alumina suspension10.1016/j.ceramint.2016.11.143 ↗
27. Vat photopolymerization 3D printing of ceramics: effects of fine powder10.1016/j.mfglet.2019.07.001 ↗
28. Fabrication and characterization of PZT suspensions for stereolithography based on 3D printing10.4191/kcers.2019.56.4.08 ↗
29. A visible light-curable yet visible wavelength-transparent resin for stereolithography 3D printing10.1038/s41427-018-0021-x ↗
30. Additive manufacturing of functionally graded ceramic materials by stereolithography
31. Surface modification of α-Al2O3 with dicarboxylic acids for the preparation of UV-curable ceramic suspensions10.1016/j.jeurceramsoc.2016.12.013 ↗
32. Development of UV-curable ZrO2 slurries for additive manufacturing (LCM-DLP) technology10.1016/j.jeurceramsoc.2019.05.023 ↗
33. Dispersion and properties of zirconia suspensions for stereolithography10.1111/ijac.13321 ↗
34. Dense 8 mol% yttria-stabilized zirconia electrolyte by DLP stereolithography10.1016/j.jeurceramsoc.2019.09.045 ↗
35. Fabrication of zirconia all-ceramic crown via DLP-based stereolithography10.1111/ijac.13441 ↗
36. Fabrication of ZrO2 and ATZ materials via UV-LCM-DLP additive manufacturing technology10.1016/j.jeurceramsoc.2019.11.037 ↗
37. Preparation and biological evaluation of ZrO2 all-ceramic teeth by DLP technology10.1016/j.ceramint.2020.01.152 ↗
38. Effect of surface treatment on the dispersion of nano zirconia particles in non-aqueous suspensions for stereolithography10.1016/j.jeurceramsoc.2018.10.024 ↗
39. Preliminary studies on additive manufacturing of over 95% dense 3Y zirconia parts via digital imaging projection10.1007/s40430-019-2157-1 ↗
40. Highly fluorinated methacrylates for optical 3D printing of microfluidic devices10.3390/mi9030115 ↗
41. Konsistenzmessungen von gummi-benzollosungen10.1007/BF01432034 ↗
42. High solid loading, low viscosity photosensitive Al2O3 slurry for stereolithography based additive manufacturing10.1016/j.ceramint.2018.09.152 ↗
43. Optimization and characterization of high-viscosity ZrO2 ceramic nanocomposite resins for supportless stereolithography
44. A mechanism for non‐newtonian flow in suspensions of rigid spheres10.1122/1.548848 ↗
45. Partially stabilized zirconia moulds fabricated by stereolithographic additive manufacturing via digital light processing10.1016/j.msea.2019.138537 ↗
46. Camargo IL · 2020
47. Effect of surfactant on dispersion of alumina in photopolymerizable monomers and their UV curing behavior for microstereolithography10.1016/j.ceramint.2014.12.066 ↗
48. Rheology of UV curable colloidal silica dispersions for rapid prototyping applications10.1016/j.jeurceramsoc.2011.05.004 ↗
49. The preparation of ZrO2-Al2O3 composite ceramic by SLA-3D printing and sintering processing10.1016/j.ceramint.2019.09.054 ↗
50. Cure behavior of colorful ZrO2 suspensions during Digital light processing (DLP) based stereolithography process10.1016/j.jeurceramsoc.2019.07.035 ↗
51. Effect of particle size distribution on the preparation of ZTA ceramic paste applying for stereolithography 3D printing10.1016/j.powtec.2019.09.066 ↗
52. A novel fabrication of yttria-stabilized-zirconia dense electrolyte for solid oxide fuel cells by 3D printing technique10.1016/j.ijhydene.2019.01.071 ↗
53. Additive manufacturing of dense alumina ceramics10.1111/ijac.12319 ↗
54. Rheological properties of zirconium oxide suspensions in acrylate monomers for use In 3D printing10.1007/s10717-018-0028-3 ↗
55. Rheological properties of PZT suspensions for stereolithography10.1016/S0955-2219(02)00036-5 ↗
56. Shaping by microstereolithography and sintering of macro-micro-porous silicon substituted hydroxyapatite10.1016/j.jeurceramsoc.2015.11.020 ↗