Hot Deformation Behavior and Microstructure Evolution of 2219/TiB2 Al-matrix Composite
Source abstract
Abstract
Hot compression tests for 2219/TiB 2 Al-matrix composite were conducted on a Gleeble-3500 isothermal simulator in the temperature range of 300~500C and strain rates of 0.01, 0.1, 1, 10s -1 to obtain true stress strain curves. The original Johnson-Cook model was calculated and used to describe the constitutive relationship of hot deformation behavior of this composite. After precision evaluation and analysis, a new modified Johnson-Cook model was proposed. Comparing with the original model, the new model has a lower absolute average relative error (AARE) of 6.4415% and a higher relative error (R) of 0.9852, which indicates better prediction precision. Meanwhile, to understand the intrinsic workability of this composite, processing map based on dynamic materials model was constructed. Two stable regions locating at 300~400C&0.01~0.1s -1 and 420~500C &0.01~1s -1 were identified by the processing map and the instable microstructure in the instability region validated the reliability of the processing map. Furthermore, the microstructure evolution was analyzed and the results revealed that the -phase reduced with the increasing temperature.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Metallurgy and Material Forming · Microstructure and mechanical properties · Powder Metallurgy Techniques and Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Chongqing Technology and Business University, School of Mechanical Engineering, China; Design and Control Key Laboratory of Manufacturing Equipment Mechanism of Chongqing, China
References (37)
Show source-provided references
1. Deformation rate effect on the microstructure and mechanical properties of Al-SiCp composites consolidated by hot extrusion10.1016/j.msea.2012.06.054 ↗
2. In situ TiB2 particulate reinforced near eutectic Al-Si alloy composites10.1016/S1359-835X(01)00124-5 ↗
3. Microstructure and mechanical characterization of in situ synthesized AA6061/(TiB2+Al2O3) hybrid aluminum matrix composites10.1016/j.jallcom.2018.01.016 ↗
4. In situ aluminum matrix composites fabricated from Al-Ni2O3 system through microwave synthesis10.1016/j.matchemphys.2015.01.021 ↗
5. The effects of Er addition on the microstructure and properties of an in situ nano ZrB2-reinforced A356.2 composite10.1016/j.jallcom.2017.10.021 ↗
6. Constitutive modeling for hot deformation behavior of Al-5083 + SiC composite
7. Effects of ultrasonic vibration treatment on particles distribution of TiB2 particles reinforced aluminum composites10.1016/j.msea.2016.10.103 ↗
8. Hot deformation behavior and constitutive modeling of homogenized 6026 aluminum alloy10.1016/j.matdes.2015.02.024 ↗
9. Correction of flow curves and constitutive modelling of a Ti-6Al-4V alloy
10. A critical review of experimental results and constitutive descriptions for metals and alloys in hot working10.1016/j.matdes.2010.11.048 ↗
11. Johnson GR · 1983 · 541
12. Dislocation‐mechanics‐based constitutive relations for material dynamics calculations10.1063/1.338024 ↗
13. A modified Johnson-Cook model for tensile behaviors of typical high-strength alloy steel10.1016/j.msea.2010.07.061 ↗
14. A GA-optimized Johnson-Cook model of flow behavior for Ti-6554 alloy in cross-phase temperature range10.1088/2053-1591/ab3885 ↗
15. A comparative study on Johnson Cook, modified Zerilli-Armstrong and Arrhenius-type constitutive models to predict elevated temperature flow behaviour in modified 9Cr-1Mo steel10.1016/j.commatsci.2009.09.025 ↗
16. A comparative study on Johnson-Cook and modified Johnson-Cook constitutive material model to predict the dynamic behavior laser additive manufacturing FeCr alloy10.1016/j.jallcom.2017.06.251 ↗
17. A comparative study on arrhenius and johnson-cook constitutive models for high-temperature deformation of Ti2AlNb-based alloys
18. Investigation on hot workability of homogenized Al-Zn-Mg-Cu alloy based on activation energy and processing map10.1007/s11837-017-2708-9 ↗
19. Deformation behavior and processing map development of AZ91 Mg alloy with and without addition of hybrid in-situ TiC+TiB2 reinforcement10.1016/j.jallcom.2018.10.276 ↗
20. A study at the workability of ultra-high strength steel sheet by processing maps on the basis of DMM
21. Flow behavior and processing maps of Ti-44.5Al-3.8Nb-1.0Mo-0.3Si-0.1B alloy10.1016/j.jallcom.2016.12.214 ↗
22. A practical condition for migration dynamic recrystallization10.1016/j.actamat.2007.01.026 ↗
23. A review of dynamic recrystallization phenomena in metallic materials10.1016/j.matdes.2016.09.012 ↗
24. Modeling of continuous dynamic recrystallization of Al-Zn-Cu-Mg alloy during hot deformation based on the internal-state-variable (ISV) method10.1016/j.ijplas.2018.03.002 ↗
25. Forging property, processing map, and mesoscale microstructural evolution modeling of a Ti-17 alloy with a lamellar (alpha+beta) starting microstructure10.1080/14686996.2017.1386530 ↗
26. Development of a processing map for use in warm-forming and hot-forming processes10.1007/BF02643490 ↗
27. Modeling of dynamic material behavior in hot deformation: forging of Ti-624210.1007/BF02664902 ↗
28. Strain rate effects on the mechanical properties of a Fe-Mn-Al alloy under dynamic impact deformations10.1016/j.msea.2004.09.055 ↗
29. Constitutive modelling of the flow behaviour of a β titanium alloy at high strain rates and elevated temperatures using the Johnson-Cook and modified Zerilli-Armstrong models10.1016/j.msea.2014.06.030 ↗
30. Hot deformation behavior and microstructure evolution of Ti-6Cr-5Mo-5V-4Al alloy during hot compression10.1016/j.vacuum.2018.11.032 ↗
31. Identification for the optimal working parameters of Ti-6Al-4V-0.1Ru alloy in a wide deformation condition range by processing maps based on DMM10.1590/1980-5373-mr-2016-0448 ↗
32. Constitutive modelling, dynamic globularization behavior and processing map for Ti-6Cr-5Mo-5V-4Al alloy during hot deformation10.1016/j.jallcom.2019.05.031 ↗
33. Gegel HL · 1987
34. Modelling of hot deformation for microstructural control10.1179/imr.1998.43.6.243 ↗
35. Ziegler H · 1963
36. Alexander JM · 1989
37. On the hot working characteristics of 2014 Al-20vol% Al2O3 metal matrix composite10.1016/j.jmatprotec.2004.09.088 ↗