Influence of inconel interlayer on microstructural, mechanical and electrochemical characteristics in single-pass ATIG welding of dissimilar austenitic and duplex stainless steel
Source abstract
Abstract
Abstract This study investigates the impact of Inconel 625 interlayer on dissimilar welded low nickel austenitic stainless steel (LNiASS) and super duplex stainless steel (S32760) using activated tungsten inert gas (ATIG) welding. Two weldments were prepared: with and without (autogenous) interlayer. Geometrical investigation of the weld cross sections revealed that interlayer-based welding significantly increased the depth of penetration and decreased weld width as compared to autogenous welding at the same welding current. The dual microstructure was observed in the weld zone (WZ) of autogenous weldment while fully austenitic structure with few intermetallics was observed in the WZ of interlayer-based weldment. Mechanical properties, particularly impact strength observed to be improved in the case of interlayer-based weldment (91 ± 2 J) compared to autogenous weldment (68 ± 2 J). Lower microhardness was noticed for the WZ of interlayer-based weldment (258 ± 3 HV0.2) than WZ of autogenous (279 ± 2 HV0.2) weldment due to the presence of higher content of Ni. However, UTS of interlayer-based weldment (654 MPa), falls short in comparison to the autogenous weldment (693 MPa), indicating a compromised joint efficiency of 5.96%. The corrosion resistance was observed to be higher for the WZ of interlayer-based weldment attributed to the higher content of Ni and Mo. The sensitization study revealed 47.33% degree of sensitization in the WZ of autogenous weldments due to dual microstructure, while interlayer-based weldments showed no sensitization.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Hydrogen embrittlement and corrosion behaviors in metals · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (56)
Show source-provided references
1. A novel perception toward welding of stainless steel by activated TIG welding: a review10.1080/10426914.2020.1854467 ↗
2. Effect of active gas on weld shape and microstructure of advanced A-TIG-welded stainless steel10.1007/s40195-016-0381-6 ↗
3. The effect of TIG welding techniques on microstructure, properties and porosity of the welded joint of 2219 aluminum alloy10.1016/j.jallcom.2017.08.157 ↗
4. Optimization of weldment in bead on plate welding of nickel based superalloy using Activated flux tungsten inert gas welding (A-TIG)10.1016/j.matpr.2019.11.327 ↗
5. Spectroscopic analysis of the arc plasma during activating flux tungsten inert gas welding process10.1016/j.jmapro.2022.01.058 ↗
6. Development of efficient activating flux for TIG welding of low-carbon steel
7. Improvement in the microstructural properties of super duplex and austenitic stainless steel dissimilar joints by incorporating Ni-based austenitic interlayer10.1016/j.mtcomm.2022.104723 ↗
8. Comparative studies on the weldability, microstructure and tensile properties of autogeneous TIG welded AISI 430 ferritic stainless steel with and without flux10.1016/j.jmapro.2015.09.008 ↗
9. Effect of activated TIG flux on performance of dissimilar welds between mild steel and stainless steel10.4028/www.scientific.net/KEM.479.74 ↗
10. Study of the performance of stainless steel A-TIG welds10.1007/s11665-007-9139-7 ↗
11. Effect of heat input on the microstructural, mechanical, and corrosion properties of dissimilar weldment of conventional austenitic stainless steel and low-nickel stainless steel10.1007/s13632-020-00681-y ↗
12. Lippold · 2005
13. Effects of rare earth metals addition on the resistance to pitting corrosion of super duplex stainless steel - Part 110.1016/j.corsci.2010.02.043 ↗
14. Kinetics of Cr/Mo-rich precipitates formation for 25Cr-6.9Ni-3.8Mo-0.3N super duplex stainless steel10.1007/s12540-012-2001-y ↗
15. Corrosion resistance of super duplex stainless steels in chloride ion containing environments: investigations by means of a new microelectrochemical method. II. Influence of precipitates10.1016/S0010-938X(00)00088-3 ↗
16. Evaluation of microstructure and mechanical properties in dissimilar austenitic/super duplex stainless steel joint10.1007/s11665-014-1136-z ↗
17. Journal of materials science & technology microstructure and corrosion resistance of dissimilar weld-joints between duplex stainless steel 2205 and austenitic stainless10.1016/j.jmst.2015.11.021 ↗
18. Dissimilar metal welding of P91 steel-AISI 316L SS with Incoloy 800 and Inconel 600 interlayers by using activated TIG welding process and its effect on the microstructure and mechanical properties10.1016/j.jmatprotec.2019.116280 ↗
19. Enhanced corrosion resistance of Cr-Mn ASS by low temperature salt bath nitriding technique for the replacement of convectional Cr-Ni ASS10.1108/ACMM-10-2018-2013 ↗
20. Development of activated tungsten inert gas welding and its current status: a review10.1080/10426914.2022.2039695 ↗
21. Techniques to weld similar and dissimilar materials by ATIG welding - an overview10.1080/10426914.2020.1802040 ↗
22. Study on Flux assisted-Tungsten inert gas welding of bimetallic P92 martensitic steel-304H austenitic stainless steel using SiO2–TiO2 binary flux10.1016/j.ijpvp.2021.104423 ↗
23. Microstructure, mechanical, and electrochemical evaluation of chrome-manganese stainless steel activated tungsten inert gas welded joint10.1007/s11665-022-06894-2 ↗
24. Experimental investigation of the flux-assisted TIG weldment of super duplex stainless steel10.1016/j.matpr.2023.08.307 ↗
25. Microwave cladding of NiCrSiC-5Al2O3 on austenitic stainless steel to improve cavitation erosion resistance
26. Effect of solidification mode and morphology of microstructure on the hydrogen content of duplex stainless steel weld metal10.1016/S0261-3069(03)00169-9 ↗
27. Gamma (γ) phase transformation in pulsed GTAW weld metal of duplex stainless steel10.1016/j.msea.2006.01.028 ↗
28. Effect of welding processes and conditions on the microstructure, mechanical properties and corrosion resistance of duplex stainless steel weldments—a review10.1016/j.jmapro.2016.11.003 ↗
29. Dissimilar welding of duplex stainless steel with Ni alloys: a review10.1016/j.ijpvp.2021.104439 ↗
30. New austenitic steels for the advanced USC power plants10.1016/B978-0-08-100552-1.00011-7 ↗
31. Formation, quantification and significance of delta ferrite for 300 series stainless steel weldments
32. Microstructure, mechanical and electrochemical evaluation of dissimilar low Ni SS and 304 SS using different filler materials10.1590/1980-5373-mr-2017-0203 ↗
33. Unmixed zone formation in austenitic stainless steel weldments
34. Characterization on the gradient microstructure near the fusion interface of dissimilar metala between high Cr heat-resistant steel and Ni-based Alloy 61710.1016/j.matchar.2019.03.001 ↗
35. Effect of active fluxes on thermophysical properties of 309L stainless-steel welds10.1016/j.jmatprotec.2017.12.018 ↗
36. Kou · 2003 · 1
37. Effect of ultrasonic welding parameters on microstructure and mechanical properties of dissimilar joints10.1016/j.matdes.2013.09.074 ↗
38. Evaluation of the thermal aging of δ-ferrite in austenitic stainless steel welds by electrochemical analysis10.1038/s41598-018-33422-x ↗
39. Effect of variation of WC reinforcement on metallurgical and cavitation erosion behavior of microwave processed NiCrSiC-WC composites clads10.1177/09544062231164517 ↗
40. A comparative study on the effect of electrode on microstructure and mechanical properties of dissimilar welds of 2205 austeno-ferritic and 316L austenitic stainless steel10.1007/s11665-022-07534-5 ↗
41. Ductile fracture by vacancy condensation in F.C.C. single crystals10.1016/1359-6454(95)00220-0 ↗
42. Directly cast bulk eutectic and near-eutectic high entropy alloys with balanced strength and ductility in a wide temperature range10.1016/j.actamat.2016.11.016 ↗
43. Quasi-static compression and deformation behavior of additively manufactured flexible polymeric lattice structure10.1007/s11665-021-06419-3 ↗
44. Autogenous tungsten inert gas welding of 430 ferritic stainless steel: the effect of inter-pass temperature on microstructure evolution and mechanical properties10.1007/s11665-020-05281-z ↗
45. Effect of post-weld heat treatment on friction welded joint of carbon steel to stainless steel10.1016/j.jmatprotec.2015.08.004 ↗
46. Effects of weld metal property and fraction on the toughness of welding joints of a 8%Ni 980 MPa high strength steel10.1016/j.jmatprotec.2010.12.011 ↗
47. Characterization of microstructure, mechanical and corrosion response in AISI 304L and Ti-stabilized 439 stainless steels weld joints10.1016/j.jmapro.2023.05.107 ↗
48. Colloids and surfaces a : physicochemical and engineering aspects synergistic impact of the functionalized graphene oxide ( fGO ) nano-sheets and Mn 2 + -doped zinc phosphate conversion film on the polyester coating corrosion protection properties10.1016/j.colsurfa.2023.132510 ↗
49. Corrosion behavior of an equiatomic CoCrFeMnNi high-entropy alloy compared with 304 stainless steel in sulfuric acid solution10.1016/j.corsci.2018.02.031 ↗
50. Surface morphology, corrosion resistance and in vitro bioactivity of P containing ZrO2 films formed on Zr by plasma electrolytic oxidation10.1016/j.jallcom.2012.11.147 ↗
51. Reviewed articles pitting corrosion of duplex stainless steels10.1108/00035590110365309 ↗
52. Nature of the passive film on nickel10.1016/S0013-4686(02)00552-2 ↗
53. Assessment of intergranular corrosion of heat treated austenitic stainless steel (AISI 316L Grade) by electron microscopy and electrochemical tests10.1134/S0033173208050172 ↗
54. Influence of Ti, C and N concentration on the intergranular corrosion behaviour of AISI 316Ti and 321 stainless steels10.1016/j.actamat.2006.11.021 ↗
55. Corrosion behavior in high heat input welded heat-affected zone of Ni-free high-nitrogen Fe-18Cr-10Mn-N austenitic stainless steel10.1016/j.matchar.2013.05.011 ↗
56. Assessment of stress corrosion cracking resistance of activated tungsten inert gas-welded duplex stainless steel joints10.1007/s11665-017-3057-0 ↗