Understanding the effect of aging treatment on the electrical properties of Al-4Cu (wt.%) alloy
Source abstract
Abstract
Abstract Binary Al–Cu alloy has always been used to illustrate the phenomenon of precipitation hardening. Meanwhile, Al–Cu alloy has good heat resistance and is a potential heat-resistant conductor material, but there is not much research work on its electrical properties. In this work, the residual resistivity variation of Al-4Cu alloy at different aging stages was investigated. At the aging temperature of 160 °C, the residual resistivity of the Al-4Cu alloy decreases with the longer aging time, and it decreases rapidly in the early stage and slowly in the later stage, mainly due to the precipitation of solid solution Cu atoms and the interface electron scattering effect of different precipitates. In the early stage, massive precipitation of Cu atoms from the matrix can effectively reduce the crystal lattice distortion of Al matrix and significantly decrease the residual resistivity. Specifically, the residual resistivity of Al-4Cu alloy that aged at 160 °C for 13 h is 3.353 μ Ω·cm, which is only 82.6% of that in the supersaturated solid solution state. In later stage of aging, the main change is the evolution of the precipitated phase, i.e., the gradual disruption of the coherent relationship between the second phase and the Al matrix. And the coherency-strain fields decrease gradually, which is also beneficial in decreasing the residual resistivity. The results show that Al–Cu alloys can also be a potential heat-resistant conductor material for the power transmission industry.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. Creep behavior of heat resistant Al–Cu–Mn alloys strengthened by fine (θ′) and coarse (Al20Cu2Mn3) second phase particles10.1016/j.msea.2019.138062 ↗
2. Developing high performance mechanical properties at elevated temperature in squeeze cast Al–Cu–Mn–Fe–Ni alloys10.1016/j.matchar.2019.01.022 ↗
3. The enhanced theta-prime (θ′) precipitation in an Al–Cu alloy with trace Au additions10.1016/j.actamat.2016.12.012 ↗
4. Optimization of phase composition of Al–Cu–Mn–Zr–Sc alloys for rolled products without requirement for solution treatment and quenching10.1016/j.jallcom.2013.08.202 ↗
5. Analysis of aluminium based alloys by calorimetry: quantitative analysis of reactions and reaction kinetics10.1179/095066004225010532 ↗
6. Effects of heat treatment on the nanoscale precipitation behavior of 7055 aluminum alloy under dynamic shock10.1016/j.vacuum.2018.03.016 ↗
7. A model for precipitation kinetics and strengthening in Al–Cu–Mg alloys10.1016/j.msea.2007.03.033 ↗
8. Theoretical and experimental study of precipitation and coarsening kinetics of θ′ phase in Al–Cu alloy10.1016/j.vacuum.2021.110263 ↗
9. The effect of silver on microstructural evolution in two 2xxx series Al-alloys with a high Cu:Mg ratio during ageing to a T8 temper10.1016/j.msea.2008.03.014 ↗
10. Interfacial stability of θ′/Al in Al–Cu alloys10.1016/j.scriptamat.2018.09.018 ↗
11. Nanostructure of aluminium alloy 2024: segregation, clustering and precipitation processes10.1016/j.actamat.2010.11.033 ↗
12. Solute segregation induced sandwich structure in Al–Cu(–Au) alloys10.1016/j.actamat.2019.11.011 ↗
13. Structure and energetics of the coherent interface between the θ′ precipitate phase and aluminium in Al–Cu10.1016/j.actamat.2011.07.059 ↗
14. Strengthening of an Al–Cu–Sn alloy by deformation-resistant precipitate plates10.1016/j.actamat.2008.03.028 ↗
15. Vacancy-tuned precipitation pathways in Al-1.7 Cu-0.025In-0.025Sb (at.%) alloy10.1016/j.actamat.2017.09.025 ↗
16. Prediction of hardness distribution during SPD process based on FEM simulations: case study of ECAP and HPT processes10.1088/2053-1591/ac1ec9 ↗
17. Microstructure of two-phase Al–1.7 at% Cu alloy deformed by equal-channel angul pressing10.1016/S1359-6454(00)00308-6 ↗
18. A nanostructural design to produce high-strength Al alloys with enhanced electrical conductivity10.1016/j.scriptamat.2013.12.002 ↗
19. The characteristics of two-phase Al–Cu and Zn–Al alloys processed by high-pressure torsion10.1088/1757-899X/63/1/012106 ↗
20. Wagner, effects of particle reinforcement and ECAP on the precipitation kinetics of an Al–Cu alloy10.1088/1757-899X/63/1/012080 ↗
21. Tensile and wear properties of repetitive corrugation and straightened Al 2024 alloy: an experimental and RSM approach10.1088/2053-1591/ac3e23 ↗
22. High electrical conductivity Al–Ag–Sc–Zr alloy with ultrafine grains processed by accumulative continuous extrusion10.1016/j.matlet.2020.129227 ↗
23. Internal friction and heat resistance of Al, Al–Ce, Al–Ce–Zr and Al–Ce–(Sc)–(Y) aluminum alloys with high strength and high electrical conductivity10.1016/j.jmrt.2021.07.054 ↗
24. Effects of thermomechanical treatment on the microstructure, precipitation strengthening, internal friction, and thermal stability of Al–Er–Yb–Sc alloys with good electrical conductivity10.1016/j.jallcom.2020.157367 ↗
25. The difference of La and Ce as additives of electrical conductivity aluminum alloys10.1016/j.matchar.2019.109963 ↗
26. Creep behavior and microstructural evolution of deformed Al–Cu–Mg–Ag heat resistant alloy10.1016/j.msea.2014.01.090 ↗
27. Enhanced mechanical properties of high-temperature-resistant Al–Cu cast alloy by microalloying with Mg10.1016/j.jallcom.2020.154305 ↗
28. Mechanical properties and corrosion resistance of Al–Cu–Mg–Ag heat-resistant alloy modified by interrupted aging10.1016/j.jallcom.2015.10.094 ↗
29. Superplastic deformation of a heat-resistant Al–Cu–Mg–Ag–Mn alloy10.1016/j.jmatprotec.2008.07.053 ↗
30. Contributions to high temperature strengthening from three types of heat-resistant phases formed during solidification, solution treatment and ageing treatment of Al–Cu–Mn–Ni alloys respectively10.1016/j.msea.2019.138819 ↗
31. Effect of cold rolling and annealing temperature on structure, hardness and electrical conductivity of rapidly solidified alloy of Al–Cu–Mn–Zr system10.1016/j.matlet.2021.130199 ↗
32. Structure and heat resistance of high strength Al–3.3%Cu–2.5%Mn–0.5%Zr (wt%) conductive wire alloy manufactured by electromagnetic casting10.1016/j.jallcom.2021.161948 ↗
33. Enhanced strength and electrical conductivity of Al–0.3Ce alloy simultaneously with Ti(C,N) nanoparticle addition10.1007/s12598-020-01465-7 ↗
34. An electrochemical study on the passivity of age hardened Al–Mg–Si alloy10.1016/j.jmrt.2020.10.077 ↗
35. Microstructural evolution and age hardening in aluminium alloys- atom probe field-ion microscopy and transmission electron microscopy studies10.1016/S1044-5803(99)00051-0 ↗
36. A multidisciplinary approach to study precipitation kinetics and hardening in an Al-4Cu (wt.%) alloy10.1016/j.jallcom.2018.04.284 ↗
37. The mechanical property and electrical conductivity evolution of Al–Fe alloy between room temperature and elevated temperature ECAP10.1016/j.vacuum.2020.109813 ↗
38. TEM study of S′ hardening precipitates in the cold rolled and aged AA2024 aluminum alloy: influence on the microstructural evolution, tensile properties & electrical conductivity10.1016/j.jmrt.2021.05.003 ↗
39. Thermal conductivity and electrical resistivity dependences on growth rate in the directionally solidified Al–Cu–Ni eutectic alloy10.1016/j.jallcom.2018.04.277 ↗
40. Mechanisms affecting hardness and electrical conductivity in artificially-aged B319 aluminum alloy10.1016/j.jallcom.2021.159121 ↗
41. Fabrication of hypoeutectic Al-4Si alloy with high electrical conductivity, high plasticity and medium strength by the dual treatment of Al matrix and eutectic Si microstructure10.1016/j.jallcom.2021.161117 ↗
42. Effects of solution heat treatment time on the as-quenched microstructure, hardness and electrical conductivity of B319 aluminum alloy10.1016/j.jallcom.2020.155577 ↗
43. Study on microstructure characterization, electrical conductivity and mechanical property improvement mechanisms of a novel Al–Si–Mg–Fe–Cu alloy10.1016/j.jallcom.2021.160959 ↗
44. Enhancing electrical conductivity and strength in Al alloys by modification of conventional thermo-mechanical process10.1016/j.matdes.2015.07.133 ↗