journal article·2020-11-01Open access

Influence of graphene oxide filler content on the dentin bond integrity, degree of conversion and bond strength of experimental adhesive. A SEM, micro-Raman, FTIR and microtensile study

Mohammed S Bin-Shuwaish, Ahmed M Maawadh, Rana S Al-Hamdan, Saad Alresayes, Thamer Ali, Basil Almutairi, Fahim Vohra, Tariq Abduljabbar

Materials Research Express· Volume 7· Issue 11

Abstract

Abstract The study aimed to evaluate the effect of graphene oxide (GO) nano-filler content in experimental dental adhesive on its degree of conversion (DC), microtensile bond strength (μTBS) and structural reliability, using Fourier transform infrared spectroscopy (FTIR), Micro-Raman spectroscopy and Scanning electron microscopy (SEM). A resin adhesive was fabricated (control adhesive - CA) and fabricated GO nano-particles were added at 0.5% and 2.0% (m/m) to produce adhesives GOA1 and GOA2 respectively. One hundred and two teeth (specimens) were prepared for dentin exposure and conditioned with 36% phosphoric acid. Specimens in each group (n = 34) were treated with formulated adhesives (CA, GOA1 & GOA2) and photo-polymerized for 20 s followed by composite build up. Sixty specimens were used forμTBS testing in the adhesive groups (CA, GOA1 & GOA2), with half exposed to thermocycling (TC) whereas the remaining half (n = 10) stored in distilled water. Seven specimens each were assessed using SEM and Micro-Raman spectroscopy, in each adhesive group (n = 7). DC for the adhesives was assessed using FTIR. The means ofμTBS and DC were analyzed using ANOVA and post hoc Tukey multiple comparisons test. GO nano-filler content showed significant influence on the adhesiveμTBS in comparison to controls (p < 0.01). Ageing (TC) revealed significant reduction in theμTBS, except in GOA2 specimens, which showed comparable outcomes among TC and non-TC specimens (p > 0.05). DC was significantly higher in control adhesive [46.8 (3.6)%] compared to GOA2 [37.7 (4.2)%] specimens, however DC was comparable among GOA1 [42.3 (2.9)%] and GOA2 [37.7 (4.2)%] specimens (p > 0.05) respectively. GO exhibited interaction within adhesive and tooth dentin comparable to control adhesive. Increasing GO content showed increase inμTBS of adhesive to dentin, but a decrease in degree of conversion. Under ideal conditions, experimental adhesive with 2% GO content showed acceptable bond strength and DC; and should be further assessed under dynamic conditions to recommend clinical use.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Dental materials and restorations · Dental Anxiety and Anesthesia Techniques · Dental Research and COVID-19

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Nanofiller loading level: influence on selected properties of an adhesive resin10.1016/j.jdent.2009.01.001 ↗
2. In vitro comparison of mechanical properties and degree of cure of bulk fill composites10.1007/s00784-012-0702-8 ↗
3. In vitro analysis of riboflavin-modified, experimental, two-step etch-and-rinse dentin adhesive: fourier transform infrared spectroscopy and micro-Raman studies10.1038/ijos.2014.49 ↗
4. Eco-friendly synthesis of graphene oxide reinforced hydroxypropyl methylcellulose/polyvinyl alcohol blend nanocomposites filled with zinc oxide nanoparticles for high-k capacitor applications10.1080/03602559.2015.1132451 ↗
5. Influence of curing mode and time on degree of conversion of one conventional and two self-adhesive resin cements10.2341/09-252-L ↗
6. Nano-graphene oxide incorporated into PMMA resin to prevent microbial adhesion10.1016/j.dental.2018.01.019 ↗
7. Comparison of mechanical, electrical and thermal properties in graphene oxide and reduced graphene oxide filled epoxy nanocomposite adhesives10.1016/j.polymer.2018.03.005 ↗
8. Graphene-based structural adhesive to enhance adhesion performance10.1039/C5RA00819K ↗
9. Graphene oxide-silica composite fillers into the experimental dental adhesives for potential therapy10.21127/yaoyimr20170012 ↗
10. Synthesis and characterization of graphene-based nanocomposites with potential use for biomedical applications10.1007/s11051-013-1512-x ↗
11. Highly dispersible graphene oxide reinforced polypyrrole/polyvinyl alcohol blend nanocomposites with high dielectric constant and low dielectric loss10.1039/C5RA11242G ↗
12. Effect of the amount of 3 methacyloxypropyl-trimethoxysilane coupling agent on physical properties of dental resin nanocomposites10.1016/j.dental.2009.03.016 ↗
13. Relationship of solvent to the photopolymerization process, properties, and structure in model dentin adhesives10.1002/jbm.a.30890 ↗
14. Effect of photoinitiator system and water content on dynamic mechanical properties of a light-cured bisGMA/HEMA dental resin10.1002/jbm.a.32617 ↗
15. Effect of metal conditioners on polymerization behavior of bonding agents10.2334/josnusd.47.171 ↗
16. Application of infrared spectroscopy to analysis of liquid hydrocarbons10.1021/ac60005a003 ↗
17. Degree of conversion of two dentin bonding agents with and without a desensitizing agent using fourier transform infrared spectroscopy: an in vitro study10.4103/0972-0707.85821 ↗
18. Effect of thermocycling, degree of conversion, and cavity configuration on the bonding effectiveness of all-in-one adhesives10.2341/14-185-LR1 ↗
19. Effect of thermocycling on the durability of etch-and-rinse and self-etch adhesives on dentin10.4012/dmj.2015-253 ↗
20. Effect of thermocycling and water storage on bond longevity of two self-etch adhesives
21. Effect of graphene oxide synthesis method on properties and performance of polysulfone-graphene oxide mixed matrix membranes10.3390/nano9050769 ↗
22. Effect of adhesives and thermocycling on the shear bond strength of a nano-composite to coronal and root dentin10.2341/09-185-L ↗
23. An introduction to silanes and their clinical applications in dentistry
24. Solvent degradation and reduced fracture toughness in aged composites10.1177/00220345920710010101 ↗
25. Role of nanoparticle dispersion and filler-matrix interface on the matrix dominated failure of rigid C60-PE nanocomposites: a molecular dynamics simulation study10.1016/j.polymer.2013.03.014 ↗
26. The effect of photopolymerization on the degree of conversion, polymerization kinetic, biaxial flexure strength, and modulus of self-adhesive resin cements10.1016/j.prosdent.2014.09.011 ↗
27. Degree of conversion of bulk-fill compared to conventional resin-composites at two time intervals10.1016/j.dental.2013.05.011 ↗
28. Effect of different carbon nano-fillers on rheological properties and lap shear strength of epoxy adhesive joints10.1016/j.compositesa.2015.12.003 ↗
29. Improved mechanical properties of carbon fiber/graphene oxide-epoxy hybrid composites10.1016/j.compscitech.2016.09.007 ↗
30. Simultaneous in situ reduction, self-alignment and covalent bonding in graphene oxide/epoxy composites10.1016/j.carbon.2013.03.034 ↗