journal article·2026-06-26Open access

Characterization of the mechanical and microstructural properties of cryogenic and austempering heat treatments on Mo alloyed ductile cast iron

Abdullah Sert

Materials Research Express· Volume 13· Issue 12

Abstract

Abstract This study examines the combined effects of molybdenum (Mo) alloying and deep cryogenic treatment (DCT) on the microstructure and mechanical response of austempered ductile iron (ADI). Ductile irons with three Mo contents (0.388, 0.671, and 0.990 wt.%) were produced, austempered at 400 °C, and subsequently subjected to DCT at −196 °C for 360 min. Microstructural and phase analyses were conducted using optical microscopy, scanning electron microscopy, high-resolution transmission electron microscopy, and x-ray diffraction (XRD). Austempering resulted in a typical ausferritic matrix, while the subsequent cryogenic step was associated with further microstructural refinement and features indicative of partial transformation of retained austenite. In addition, fine secondary features were observed locally and attributed to carbide-like precipitates. Quantitative XRD analysis revealed the presence of α and γ reflections in all heat-treated conditions. Detailed diffraction scans exhibited a distinct peak shift toward lower 2 θ angles following DCT, indicating an expansion of the lattice parameters and a corresponding enrichment of carbon within the austenite phase. In terms of mechanical response, the integration of austempering and DCT led to a 16.6% increase in hardness compared to the as-cast state. Furthermore, the combined heat treatment cycle resulted in a 42.3% enhancement in impact energy relative to the initial cast condition, highlighting the potential of DCT to optimize the structural integrity and toughness of Mo-alloyed ADI.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels · Surface Treatment and Residual Stress

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Eskisehir Osmangazi University

Funding

Eskişehir Osmangazi Üniversitesi

References (37)

Show source-provided references
1. Wear behavior of austempered ductile irons with dual matrix structures10.1016/j.msea.2006.06.058 ↗
2. An investigation on the stability of austenite in austempered ductile cast iron (ADI)10.1016/j.msea.2014.12.046 ↗
3. Effect of ausferrite volume fraction and morphology on tensile properties of partially austenitised and austempered ductile irons with dual matrix structures10.1179/136404607X256051 ↗
4. Microstructural and crystallographic features of ausferrite in as-cast gray iron10.1016/j.matchar.2004.07.008 ↗
5. Microstructure and mechanical properties of austempered ductile iron with different strength grades10.1016/j.matlet.2013.12.083 ↗
6. A review: phase transformation and wear mechanisms of single-step and dual-step austempered ductile irons10.1016/j.jmrt.2019.10.074 ↗
7. Austempered materials for powertrain applications10.1007/s11665-013-0557-4 ↗
8. Microstructure, wear behavior and surface hardening of austempered ductile iron10.1016/j.jmrt.2020.06.077 ↗
9. Microstructural and mechanical properties of Cu–Ni–Mn–Mo austempered ductile iron obtained from two-step hot air austempering10.1016/j.jmrt.2020.01.045 ↗
10. The effect of cryogenic treatment on hardness, toughness, and tribological properties of austempered ductile iron with different nickel contents10.1007/s40962-021-00686-5 ↗
11. The effect of copper content on the microstructure and mechanical properties of austempered, cryogenically treated ductile iron (ADI)10.1007/s40962-025-01756-8 ↗
12. Metallography of bainitic transformation in austempered ductile iron10.1179/mst.1992.8.12.1095 ↗
13. Austempered ductile iron: an alternative material for earth moving components10.1016/S0958-9465(02)00078-1 ↗
14. Characterization of the mechanism of cryogenic treatment on the microstructural changes in tungsten carbide cutting tools10.1016/j.matchar.2019.01.033 ↗
15. Enhancing the wear resistance of case carburized steel (En 353) by cryogenic treatment10.1016/j.cryogenics.2005.10.004 ↗
16. Improving tribological properties of tool steels through combination of deep-cryogenic treatment and plasma nitriding10.1016/j.wear.2011.04.001 ↗
17. Improvement in abrasion wear resistance and microstructural changes with deep cryogenic treatment of austempered ductile cast iron (ADI)10.1007/s11661-016-3659-4 ↗
18. Development of austenite free ADI (austempered ductile cast iron)10.1016/j.msea.2006.07.086 ↗
19. Molybdenum alloying in cast iron and steel10.1007/s40436-019-00282-1 ↗
20. Influence of molybdenum on austempering behaviour of ductile iron. Part 1: austempering kinetics and mechanical properties of ductile iron containing 0.13% Mo10.1179/026708399101506247 ↗
21. Influence of molybdenum on austempering behaviour of ductile iron. Part 3: austempering kinetics, mechanical properties and hardenability of ductile iron containing 0.25% Mo10.1179/026708399101506689 ↗
22. Influence of molybdenum on austempering behaviour of ductile iron. Part 4: austempering behaviour of ductile iron containing 0.45% Mo10.1179/026708399101506698 ↗
23. Combined effects of molybdenum and cooling rate on microstructure and tribo-mechanical properties of ductile iron10.1007/s40962-025-01782-6 ↗
24. Microstructure and abrasive wear resistance of an alloyed ductile iron subjected to deep cryogenic and austempering treatments10.1016/j.jmst.2017.08.003 ↗
25. Enhanced plasticity of austempered ductile iron (ADI) by partitioning treatment10.1016/j.msea.2020.140513 ↗
26. Austempered ductile iron (ADI): influence of austempering temperature on microstructure, mechanical and wear properties and energy consumption10.3390/met8010053 ↗
27. Austenite decomposition and carbon partitioning during quenching and partitioning heat treatments studied via in-situ x-ray diffraction10.1016/j.matdes.2019.107862 ↗
28. Effects of austenitizing process on microstructures and properties of carbidic austempered ductile iron10.1088/2053-1591/aae44c ↗
29. Influence of temperature and point defects on the x-ray diffraction pattern of graphite10.1016/j.cartre.2021.100124 ↗
30. Influence of cooling rate on the microstructure and properties of a new wear resistant carbidic austempered ductile iron (CADI)10.1016/j.matchar.2012.07.005 ↗
31. Effect of alloying elements on austempered ductile iron (ADI) properties and its process: review
32. Characteristics of tempering response of austempered ductile iron10.1016/j.jmrt.2017.08.005 ↗
33. Investigation into mechanical properties of austempered ductile cast iron (ADI) in accordance with austempering temperature10.1016/j.matlet.2007.05.034 ↗
34. Effects of alloying elements (Mo, Ni and Cu) on the austemperability of GGG-60 ductile cast iron10.3390/met7080320 ↗
35. The effects of molybdenum and manganese on the mechanical properties of austempered ductile iron10.17559/TV-20170124120729 ↗
36. An investigation on the stability of austenite in austempered ductile cast iron (ADI)10.1016/j.msea.2014.12.038 ↗
37. Influence of austempering temperatures on the microstructure and mechanical properties of austempered ductile cast iron10.3390/met11060967 ↗