Regression and Grey relational analysis on friction and wear behavior of AA6061/Al2O3/Si3N4/graphite hybrid nano composites
Source abstract
Abstract
Nowadays, the hybrid nano composites are chosen as suitable replacement for conventional metal matrix composites in order to overcome the drawbacks like porosity, dispersion and bonding of reinforcement in matrix material. The experiments were designed and the results were optimized using Taguchi L9 orthogonal array method with 3 factors and 3 levels. The aim of this research work was to identify the significance of Si3N4 nano particles in tribological characteristics of AA6061/Al2O3/Si3N4/graphite hybrid nano composites. The ASTM G99 standard was followed to conduct the wear test of the prepared hybrid nano composites. A statistical analysis was performed to establish a mathematical relation for wear rate and friction coefficient against the amount of Si3N4 nano particles, sliding speed and normal load. Grey relational analysis (GRA) was employed to identify the synergetic effect of input parameter on multiple response parameters (i.e. wear rate and COF). The wear mechanisms of the composites were interpreted using the micrographs obtained from Scanning Electron Microscope (SEM). The increasing wt% of Si3N4 nano particle reduced the values of friction coefficient and wear rate. The sliding speed of 1 m s−1, normal load of 10 N and the weight percentage of Si3N4 (4%) were noted as optimum combination of parameters resulted from GRA. The wear surfaces of the composites with 4 wt% Si3N4 nano pariticles were noticed with mild scratches. Shallow grooves and micro cuts were observed on the worn out surface of the composite which were tested at 4 m s−1. The plastic deformation and fracture of plateau were also found out on the worn surface.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Tribology and Wear Analysis · Orthopaedic implants and arthroplasty
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (19)
Show source-provided references
1. Abrasive wear behaviour of SiC/2014 aluminum composite10.1016/j.triboint.2009.12.056 ↗
2. Dry sliding wear behaviour of aluminum based hybrid composites with graphite nano fiber—alumina fiber10.1016/j.matdes.2011.02.064 ↗
3. Experimental optimization of dry sliding war behaviour of in situ AlB2/Al composite based on Taguchi’s method10.1016/j.matdes.2012.05.048 ↗
4. Taguchi approach to influence of procssing parameters on erosive wear behaviour of Al7034-T6 composites10.1016/S1003-6326(17)60242-5 ↗
5. Parametric optimization of dry sliding wear loss of copper—MWCNT composites10.1016/S1003-6326(17)60070-0 ↗
6. The prediction of wear resistance model for the metal matrix composites10.1016/j.wear.2004.11.024 ↗
7. Optimization of testing parameters on the wear behavior of metal matrix composites based on the Taguchi method10.1016/j.msea.2004.11.012 ↗
8. Tribological behaviour of metal matrix and its composite10.1016/j.matdes.2006.01.032 ↗
9. Modeling and optimization of Al/SiCp MMC machining using Taguchi approach10.1016/j.measurement.2013.06.001 ↗
10. Composition modulation in one-dimensional and two-dimensional chalcogenide semiconductor nanostructures’10.1039/C8CS00418H ↗
11. Lateral growth of composition graded atomic layer MoS2(1−x)Se2x nano sheets10.1021/jacs.5b01594 ↗
12. Strain-tuning atomic substitution in two-dimensional atomic crystals10.1021/acsnano.8b01646 ↗
13. Optimization of friction and wear behaviour of Al-Si3N4 Nano composite and Al-Gr-Si3N4 Hybrid composite under dry sliding conditions10.1016/S1003-6326(17)60116-X ↗
14. Dry sliding wear behaviour of heat treated hybrid metal matrix composite using Taguchi techniques10.1016/j.matdes.2014.06.007 ↗
15. Fabrication and wear characterization of silicon carbide and copper reinforced aluminium matrix composite10.1016/j.md.2018.01.002 ↗
16. Modeling the abrasive wear charactersitics of in situ Al-12%Si/TiC composites10.1016/j.matdes.2013.02.042 ↗
17. Influence of metal powder premixing on mechanical behavior of dualreinforcement (Al2O3 (mm)/Si3N4 (nm)) in AA6061 matrix10.1016/j.jallcom.2017.10.002 ↗
18. Optimization of machining parameters for turning operation with multiple quality characteristics using grey relational analysis10.17559/TV-2015052613171 ↗
19. Developing a mathematical model to evaluate wear rate of AA7075/SiCp powder metallurgy composites10.1016/j.wear.2007.08.006 ↗