Study on formability and strain hardening index: influence of particle size of boron carbide (B4C) in magnesium matrix composites fabricated by powder metallurgy technique
Source abstract
Abstract
Abstract In the present investigation, Magnesium composites have been fabricated with boron carbide (B4C) as reinforcement by powder metallurgicaltechnique. Two different particle sizes—micro and nano B4C particles with weight percentage of 0%, 5% and 10% has been studied. The green compacts were prepared by cold pressing and then sintering the specimens before being subjected to cold upsetting under triaxial stress state condition in order to study the phenomenon of workability and instantaneous strain hardening index. Powder characterizations are discussed using x-ray Diffraction peaks, Scanning Electron Microscope images and Energy Dispersive Spectrum analysis. Cold upsetting has been preferred to investigate the performance of the composites. The values of formability stress index factor (β σ ), various stress ratio (σ θ /σ eff , σ m /σ eff andσ z /σ m ) parameters and instantaneous strain hardening index (n i ) are observed for increase in % of B4C particles and its sizes. The experimental results were analyzed pertaining to relative density. The results reveal that Mg-10% nano B4C composite has higher relative density, formability stress index factor and hence high workability than the other composites. The addition of B4C particles as reinforcement affects the strain hardening index due to geometric and work hardening of the composites.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Powder Metallurgy Techniques and Materials · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. Microstructure and mechanical properties of disperse reinforced composite material with AZ91 matrix alloy10.1134/S2075113313040102 ↗
2. Comparative study on the mechanical and microstructural characterization of AA 7075 nano and hybrid nanocomposites produced by stir and squeeze casting10.1016/j.jare.2017.02.005 ↗
3. Potential magnesium alloys for high temperature die cast automotive applications: a review10.1081/AMP-120024970 ↗
4. Friedrich · 200610.1007/3-540-30812-1 ↗
5. The study on corrosion resistance of superhydrophobic magnesium hydroxide coating on AZ31B magnesium alloy10.1016/j.colsurfa.2019.05.060 ↗
6. TiNiReinforced magnesium composites by powder metallurgy10.1002/9781118062029.ch86 ↗
7. Synthesis of magnesium metallic matrix composites and the evaluation of aluminium nitride addition effect10.1016/j.jallcom.2015.12.078 ↗
8. Magnesium metal matrix composites—a review
9. Mechanical behavior and wear prediction of stir cast Al-TiB2 composites using response surface methodology10.1016/j.matdes.2014.02.053 ↗
10. Determination of abrasive wear behaviour of al-fly ash metal matrix composites produced by squeeze casting10.1016/j.matpr.2018.01.075 ↗
11. Fabrication of Magnesium-Boron carbide metal matrix composite by powder metallurgy route: comparison between microwave and spark plasma sintering10.1016/j.jallcom.2016.12.146 ↗
12. Wear behavior and mechanism of B4C reinforced Mg-matrix composites fabricated by metal-assisted pressureless infiltration technique10.1016/S1003-6326(15)63873-0 ↗
13. Boron carbide: structure, properties, and stability under stress10.1111/j.1551-2916.2011.04865.x ↗
14. Complex shaped boron carbides from negative additive manufacturing10.1016/j.matdes.2018.03.026 ↗
15. Fabrication and mechanical properties of aluminium-boron carbide composites’, Int
16. Processing, microstructures, and mechanical properties of magnesium matrix composites: a review10.1007/s40195-014-0161-0 ↗
17. Fabrication of Al7075/B4C surface composite by novel Friction Stir Processing ( FSP ) and investigation on wear10.1016/j.protcy.2016.03.058 ↗
18. Experimental and prediction of sintered Cu-W composite by using artificial neural networks10.1016/j.matdes.2012.08.056 ↗
19. Cyclic stress response of Al–Cu–Mg alloy matrix composites with SiCp of varying sizes10.1016/S1359-6462(98)00065-7 ↗
20. Yield behavior of cold compacted composite powders10.1016/S1359-6454(00)00151-8 ↗
21. The formability of the Al–5% SiC composite obtained using P/M method10.1016/0924-0136(96)02408-9 ↗
22. Experimental investigation on workability and strain hardening behaviour of Fe–C–0.5 Mn sintered composites10.1016/j.matdes.2012.04.053 ↗
23. ‘Workability behaviour of powder metallurgy aluminium composites10.1155/2014/368721 ↗
24. An investigation on instantaneous strain hardening behavior in three dimensions of aluminum–iron composites during cold upsetting10.1016/j.msea.2004.11.016 ↗
25. An experimental investigation on strain hardening behaviour of aluminium–3.5% alumina powder metallurgy composite preform under various stress states during cold upset forming10.1016/j.matdes.2006.01.010 ↗
26. Comparison of workability strain, stress parameters of powder metallurgy steels AISI 9840, and AISI 9845 during cold upsetting10.1016/j.matdes.2008.04.023 ↗
27. Phenomenon of instantaneous strain hardening behavior of sintered Al–Fe composite preforms during cold axial forming10.1016/j.matdes.2006.01.020 ↗
28. Some aspects on strain hardening behavior in three dimensions of aluminum–iron powder metallurgy composite during cold upsetting10.1016/j.matdes.2004.12.012 ↗
29. Hot workability of nanocrystalline AZ91 magnesium alloy10.1016/j.jallcom.2014.01.091 ↗
30. Hot deformation behavior and workability characteristics of bimodal size SiCp/AZ91 magnesium matrix composite with processing map10.1016/j.matdes.2014.07.039 ↗
31. Some aspects of workability studies on hot forging of sintered high strength 4% titanium carbide composite steel preforms10.1016/j.msea.2006.03.035 ↗
32. Effect of geometric work-hardening and matrix work-hardening on workability and densification of aluminium-3.5% alumina composite during cold upsetting10.1016/j.matdes.2007.11.006 ↗
33. Deformation Behavior of Sintered Fe-C-Mn Composite During Cold Upset Forming10.1080/10426914.2010.544820 ↗
34. Some investigation on the cold deformation behaviour of sintered iron-0.8% carbon alloy powder preforms10.1016/j.jmatprotec.2007.10.068 ↗
35. Influence of carbon content on Workability and Density ratio of Sintered Iron Based Composites
36. Effect of particle size of SiC in aluminium matrix on workability and strain hardening behaviour of P/M composite10.1016/j.msea.2008.11.037 ↗
37. Hot workability and densification behavior of sintered powder metallurgy Al-B4C preforms during upsetting10.1016/j.jmapro.2017.06.012 ↗
38. Hot deformation behavior of extruded AZ80C magnesium alloy10.1016/S1003-6326(13)62850-2 ↗
39. Tensile, compressive and wear behaviour of self-lubricating sintered magnesium based composites10.1016/S1003-6326(17)60036-0 ↗
40. Strain hardening analysis and modelling of its parameters for sintered Al and Al-1%C preforms during cold upsetting10.1016/j.jmrt.2018.12.009 ↗
41. Microstructure, consolidation and mechanical behaviour of Mg/n-TiC composite10.1016/j.aej.2016.06.033 ↗
42. Electrical resistivity, wear map and modeling of extruded tungsten reinforced copper composite10.1016/j.matdes.2013.11.070 ↗
43. Experimentalinvestigation on workability and strain hardening behaviour of Fe–C–Mnsinteredcomposites with different percentage of carbon and manganese content10.1016/j.matdes.2013.02.002 ↗
44. Workability studies on sintered Cu-10SiC preforms during cold axial upsetting10.1016/j.matdes.2012.02.004 ↗
45. Some aspects on workability of aluminium– iron powder metallurgy composite during cold upsetting10.1016/j.msea.2004.09.018 ↗
46. A new workability criterion for ductile metals10.1115/1.3225876 ↗