journal article·2019-07-31

Microstructure, compression and creep properties of Al-5%Cu-0.8Mn/5%B4C composites

A Lotfy, A V Pozdniakov, V S Zolotorevskiy, E Mohamed, M T Abou El-Khair, A Daoud, F Fairouz

Materials Research Express· Volume 6· Issue 9
Publisher page

Abstract

Under mechanical stirring, 5% of B 4 C ceramic particles were added to Al-5%Cu-0.8Mn matrix alloy subsequently, the produced composites were re-melted and squeezed using squeeze casting route. Microstructure evolution was characterized using TEM, SEM and XRD analyses. 0.8Mn were added to Al-5%Cu-5%B 4 C to investigate their effect on thermal expansion coefficient (CTE). The matrix along with its composites were tested by compression test at room and elevated temperatures. At room and 200 °C compression test temperatures, the addition of Mn to the composites lead to YS improvement from 248 to 360 MPa and from 190 to 242 MPa at room and 200 °C temperatures respectively. The addition effect of 0.8Mn on the strain rate ε , % was more pronounced at high temperature. The creep rupture test was performed for one hour and 260 °C at different constant stresses after wards, the creep fracture surfaces were examined by SEM analysis. As compared with A355 piston alloy, the Al-5%Cu-0.8Mn-5%B 4 C composites showed more creep resistance allowing it to be a suitable replacement for A355 alloy in automotive industries. The experimental and simulated creep results were compared with each other to investigate the integrity of the actual results with simulated one, the result as well found to be fairly integrated and similar.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced materials and composites · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. 10.1016/j.jestch.2017.08.00410.1016/j.jestch.2017.08.004 ↗
2. 10.1007/s12666-014-0399-210.1007/s12666-014-0399-2 ↗
3. 10.4149/km_2011_4_25310.4149/km_2011_4_253 ↗
4. 10.1016/j.compscitech.2005.05.02710.1016/j.compscitech.2005.05.027 ↗
5. 10.1016/S0924-0136(00)00639-710.1016/S0924-0136(00)00639-7 ↗
6. 10.1179/095066009X1257253017054310.1179/095066009X12572530170543 ↗
7. 10.1016/j.msea.2016.12.04410.1016/j.msea.2016.12.044 ↗
8. 10.1007/s12666-012-0227-510.1007/s12666-012-0227-5 ↗
9. 10.1016/j.msea.2017.05.10110.1016/j.msea.2017.05.101 ↗
10. 10.1016/j.msea.2004.01.13110.1016/j.msea.2004.01.131 ↗
11. 10.1007/s10853-011-6131-210.1007/s10853-011-6131-2 ↗
12. 10.1016/j.msea.2008.11.01010.1016/j.msea.2008.11.010 ↗
13. 10.1016/j.matpr.2015.07.02610.1016/j.matpr.2015.07.026 ↗
14. 10.1016/j.jare.2017.02.00510.1016/j.jare.2017.02.005 ↗
15. 10.1016/j.msea.2016.07.05810.1016/j.msea.2016.07.058 ↗
16. 10.1016/j.matpr.2017.09.04010.1016/j.matpr.2017.09.040 ↗
17. 10.1016/j.msea.2016.01.11410.1016/j.msea.2016.01.114 ↗
18. 10.1007/s13369-014-1157-910.1007/s13369-014-1157-9 ↗
19. 10.1016/j.jmrt.2015.02.00510.1016/j.jmrt.2015.02.005 ↗
20. 10.1134/S0031918X1606010710.1134/S0031918X16060107 ↗
21. 10.1016/j.jallcom.2015.12.22810.1016/j.jallcom.2015.12.228 ↗
22. Alaneme K K · ACTA TECHNICA CORVINIENSIS- Bulletin of Engineering · 2013 · 3 · 105
23. 10.1016/j.ceramint.2016.09.18710.1016/j.ceramint.2016.09.187 ↗
24. 10.1080/1042691090318003710.1080/10426910903180037 ↗
25. Thirimalai T · J. Sci. Ind. Res. · 2014 · 73 · 667
26. 10.1016/j.jnucmat.2017.02.02010.1016/j.jnucmat.2017.02.020 ↗
27. 10.1016/j.msea.2017.01.07510.1016/j.msea.2017.01.075 ↗
28. 10.1016/j.matchar.2017.12.01510.1016/j.matchar.2017.12.015 ↗
29. 10.1007/s11665-017-2734-310.1007/s11665-017-2734-3 ↗
30. 10.1177/002199831562625810.1177/0021998315626258 ↗
31. 10.1016/S0921-5093(02)00039-410.1016/S0921-5093(02)00039-4 ↗
32. 10.1007/BF0302633910.1007/BF03026339 ↗