Study on corrosion resistance of HAZ and TMAZ in friction stir welding joint of 7075 aluminum alloy by thermal simulation
Source abstract
Abstract
Abstract It is difficult to characterize the variation of corrosion resistance of the narrow areas in friction stir welding (FSW) joints due to the large temperature gradient. In this paper, the welding thermal simulation was performed to simulate the heat affected zone (HAZ) and thermo-mechanical affected zone (TMAZ) of the FSW 7075-T6 aluminum alloy, and the corrosion resistance and microstructure of the simulated samples were studied. Results show that the corrosion potential changes greatly under different thermal simulation temperatures. The pitting corrosion of the HAZ simulated samples presents two pitting potentials, but for the TMAZ simulated samples, two pitting potentials will gradually evolve to one pitting potential with the increase of the maximum temperature. The electrochemical impedance spectroscopy results show that the corrosion mechanism of the HAZ and TMAZ is completely inconsistent, which is related to the differences in precipitate and grain characteristics.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. Effect of welding speed on performance of friction stir welded spray forming 7055 aluminum alloy10.1016/j.jmapro.2019.08.019 ↗
2. Effects of Friction Stir Processing Parameters and In Situ Passes on Microstructure and Tensile Properties of Al-Si-Mg Casting10.1007/s11661-014-2494-8 ↗
3. Low temperature superplasticity in a friction-stir-processed ultrafine grained Al–Zn–Mg–Sc alloy10.1016/j.actamat.2005.05.021 ↗
4. Understanding precipitate evolution during friction stir welding of Al-Zn-Mg-Cu alloy through in situ measurement coupled with simulation10.1016/j.actamat.2018.01.020 ↗
5. Effects of base metal state on the microstructure and mechanical properties of Al–Mg–Si alloy friction stir-welded joints10.1016/j.jmapro.2020.04.084 ↗
6. Relationship between microstructure, microhardness and corrosion sensitivity of an AA 2024-T3 friction stir welded joint10.1016/j.corsci.2011.05.049 ↗
7. The time–temperature–corrosion susceptibility in a 7050-T7451 friction stir weld10.1016/j.msea.2008.03.039 ↗
8. Microstructure mapping in friction stir welds of 7449 aluminium alloy using SAXS10.1016/j.actamat.2006.06.015 ↗
9. Microstructure and corrosion behavior of the ultra-fine grained aluminum coating fabricated by friction surfacing10.1016/j.matlet.2019.05.022 ↗
10. Microstructural variation due to heat gradient of a thick friction stir welded aluminum 7449 alloy10.1016/j.jallcom.2017.04.147 ↗
11. Double-side friction stir welded cast 2297 Al–Cu–Li alloy at various parameters10.1007/s12666-019-01640-0 ↗
12. Physical simulation of a duplex stainless steel friction stir welding by the numerical and experimental analysis of hot torsion tests10.1007/s11661-016-3631-3 ↗
13. CA6NM stainless steel Unpublished to different thermal cycles in the gleeble weld simulator10.1007/s40430-018-1375-2 ↗
14. Hot ductility behaviors in the weld heat-affected zone of nitrogen-alloyed Fe-18Cr-10Mn austenitic stainless steels10.1007/s11661-015-2771-1 ↗
15. Quench induced residual stress prediction in heat treatable 7xxx aluminium alloy thick plates using gleeble interrupted quench tests10.1016/j.jmatprotec.2015.03.029 ↗
16. A study of linear friction weld microstructure in single crystal CMSX-486 superalloy10.1007/s11661-011-0928-0 ↗
17. Thermal analysis of friction stir welding process and investigation into affective parameters using simulation10.1007/s12206-015-0149-3 ↗
18. Understanding precipitate evolution during friction stir welding of Al-Zn-Mg-Cu alloy through in situ measurement coupled with simulation10.1016/j.actamat.2018.01.020 ↗
19. Corrosion behavior and mechanical properties of Al-Zn-Mg aluminum alloy weld10.1016/j.corsci.2017.05.007 ↗
20. Corrosion behaviour and mechanism of new aerospace Al–Zn–Mg alloy friction stir welded joints and the effects of secondary Al3ScxZr1−x nanoparticles10.1016/j.corsci.2014.10.036 ↗
21. Prediction of generation of high- and low-angle grain boundaries (HAGB and LAGB) during severe plastic deformation10.1007/s11661-020-05873-3 ↗
22. Microstructure and texture evolution during annealing a cryogenic-SPD processed Al-alloy with a nanoscale lamellar HAGB grain structure10.1016/j.actamat.2009.04.010 ↗
23. Mechanical behavior and microstructure evolution during deformation of AA7075-T65110.1016/j.msea.2021.141615 ↗
24. Effect of copper content on chromate conversion coating protection of 7xxx-T6 aluminum alloys10.5006/1.3287823 ↗
25. Stress corrosion cracking behavior of friction stir welded 5052-H112 Al–Mg alloy10.1016/j.vacuum.2020.109299 ↗