Laser-induced exothermic bonding of carbon fiber/Al composites and TiAl alloys
Source abstract
Abstract
Abstract In this paper, a highly-efficient method for bonding Carbon Fiber (C f )/Al composites and TiAl alloys was developed by means of laser-induced exothermic reaction of a Ni-Al-Ti interlayer. To examine the interlayer exothermic performance, the adiabatic temperature was calculated and the reaction temperatures were measured. Based on SEM, XRD and TEM, the interfacial reactions between carbon fiber and interlayer products were investigated. Results show that the addition of Ti enhanced the interfacial reactions between carbon fibers and interlayer products. The resulting formation of a 300–400 nm thin Ti-C layer at the NiAl 3 /carbon fiber interface was identified as a key player in improving the joining quality on the C f /Al side. The typical interfacial structure of the joint is (C f /Al)/Ti-C/NiAl 3 /Ni 2 Al 3 /(NiAl + Al 3 NiTi 2 )/Al 3 NiTi 2 /TiAl. The joint formation mechanism was discussed. In addition, the effect of Ti content on the microstructure and mechanical properties of joints were investigated in detail. The optimum value of Ti content was found to be 5 wt.%, leading to a defect-free joint and a maximum shear strength of 45.8 MPa.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · High Entropy Alloys Studies · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. Carbon nanotubes—the route toward applications10.1126/science.1060928 ↗
2. Advances in the science and technology of carbon nanotubes and their composites: a review10.1016/S0266-3538(01)00094-X ↗
3. In-situ characterization of interfacial shear strength in multi-walled carbon nanotube reinforced aluminum matrix composites10.1016/j.carbon.2016.05.015 ↗
4. Effects of joining conditions on microstructure and mechanical properties of Cf/Al composites and TiAl alloy combustion synthesis joints10.1007/s40195-015-0209-9 ↗
5. Effect of graphite and granite dust particulates as micro-fillers on tribological performance of Al 6061-T6 hybrid composites10.1016/j.triboint.2015.07.035 ↗
6. Laser and resistance joining of aluminum–graphite composite10.1016/j.jmatprotec.2012.06.001 ↗
7. Simple fabrication of large-area corrosion resistant superhydrophobic surface with high mechanical strength property on TiAl-based composite10.1016/j.jmatprotec.2016.08.024 ↗
8. Effect of Ti–Al content on microstructure and mechanical properties of Cf/Al and TiAl joint by laser ignited self-propagating high-temperature synthesis10.1016/S1003-6326(15)63747-5 ↗
9. Effects of trace alloying elements on the phase transformation behaviors of ordered ω phases in high Nb-TiAl alloys10.1016/j.matdes.2016.10.004 ↗
10. Joining of Cf/Al composites and TiAl intermetallics by laser-induced self-propagating high-temperature synthesis using the Ni-Al-Zr interlayer10.1016/j.matdes.2016.07.128 ↗
11. Ultrasonic-assisted brazing of Al–Ti dissimilar alloy by a filler metal with a large semi-solid temperature range10.1016/j.matdes.2016.01.109 ↗
12. Microstructure evolution and mechanical properties of ZrO2/TiAl joints vacuum brazed by Ag–Cu filler metal10.1016/j.msea.2015.05.059 ↗
13. Vacuum brazing high Nb-containing TiAl alloy to Ti60 alloy using Ti-28Ni eutectic brazing alloy10.1016/j.jallcom.2016.09.074 ↗
14. Mechanical milling of Ti–Ni–Si filler metal for brazing TiAl intermetallics10.1016/j.intermet.2011.01.017 ↗
15. Interfacial microstructure and forming mechanism of brazing Cf/Al composite with Al-Si filler10.1016/j.msea.2006.02.013 ↗
16. Infrared brazing of TiAl using Al-based braze alloys10.1016/S0966-9795(03)00077-3 ↗
17. FEA evaluation of the Al4C3 formation effect on the Young's modulus of carbon nanotube reinforced aluminum matrix composites10.1016/j.compstruct.2015.03.032 ↗
18. Tribological characterization of Al7075-graphite composites fabricated by mechanical alloying and hot extrusion10.1016/j.matdes.2014.11.045 ↗
19. Effect of aluminum carbide on thermal conductivity of the unidirectional CF/Al composites fabricated by low pressure infiltration process10.1016/j.compscitech.2014.03.022 ↗
20. Interface structure in graphite-fiber-reinforcedmetal-matrix composites10.1002/sia.1095 ↗
21. Microstructure evolution and formation mechanism of laser ignited SHS joining between Cf/Al composites and TiAl alloys with Ni-Al-Ti interlayer
22. Combustion synthesis in bi-layered (Ti−Al)/(Ni−Al) system10.1016/j.jmatprotec.2016.09.010 ↗
23. Self-propagating high-temperature synthesis of refractory inorganic compounds
24. A thermal analysis on self-propagating high temperature synthesis in joining technology10.1016/j.commatsci.2011.08.015 ↗
25. High-efficiency joining of Cf/Al composites and TiAl alloys under the heat effect of laser-ignited self-propagating high-temperature synthesis10.1016/j.jmst.2016.01.016 ↗
26. Microwave assisted combustion synthesis in the system Ti-Si-C for the joining of SiC: experimental and numerical simulation results10.1016/j.jeurceramsoc.2013.03.005 ↗
27. Joining of nickel monoaluminide to a superalloy substrate by high pressure self-propagating high-temperature synthesis10.1016/S0925-8388(01)01924-7 ↗
28. Microstructure evolution and reaction mechanism during reactive joining of TiAl intermetallic to TiC cermet using Ti-Al-C-Ni interlayer10.1016/j.jallcom.2006.07.040 ↗
29. Combustion joining of carbon-carbon composites to TiAl intermetallics using a Ti-Al-C powder composite interlayer10.1016/j.compscitech.2015.05.001 ↗
30. Combustion joining of refractory materials: carbon-carbon composites10.1557/JMR.2008.0008 ↗
31. Processing of intermetallic compounds for structural applications at high temperature10.1016/0966-9795(96)00016-7 ↗
32. Joining of the intermetallic compound TiAl using self-propagating high-temperature synthesis reaction
33. A simplified computational model of the oxidation of Zr/Al multilayers10.1016/j.combustflame.2014.07.010 ↗
34. Combustion joining of carbon/carbon composites by a reactive mixture of titanium and mechanically activated nickel/aluminum powders10.1016/j.ceramint.2013.02.099 ↗
35. Molecular dynamics simulation of the energetic reaction between Ni and Al nanoparticles10.1063/1.3073988 ↗
36. Rogachev · 2015
37. Self-propagating exothermic reactions: the synthesis of high temperature materials by combustion10.1016/S0920-2307(89)80002-7 ↗
38. Effects of liquid phases on densification of TiO2-doped Al2O3-ZrO2 composite ceramics10.1016/j.ceramint.2013.08.049 ↗
39. Tribological properties of NiAl-based composites containing Ag3VO4 nanoparticles at elevated temperatures10.1016/j.triboint.2014.06.014 ↗
40. The ternary system Al–Ni–Ti part I: isothermal section at 900°C; experimental investigation and thermodynamic calculation10.1016/S0966-9795(99)00054-0 ↗
41. Interfacial microstructure and joining properties of TiAl/Ti3AlC2 diffusion bonded joints using Zr and Ni foils as interlayer10.1016/j.vacuum.2013.10.024 ↗
42. Composition, microstructure, phase constitution and fundamental physicochemical properties of low-melting-point multi-component eutectic alloys10.1016/j.jmst.2016.08.022 ↗
43. Changing the alloy composition of Al7075 for better processability by selective laser melting10.1016/j.jmatprotec.2016.08.003 ↗
44. Merzhanov · 2007
45. Strain-aging and breakaway strain amplitude of damping in NiAl and NiAlZr10.1557/JMR.1994.1166 ↗