journal article·2017-06

Ultra thin silicon wafer slicing using wire-EDM for solar cell application

Kamlesh Joshi, A. Ananya, Upendra Bhandarkar, Suhas S. Joshi

Materials & Design· Volume 124
Publisher page

Abstract

Abstract The ever increasing demand of silicon solar cells in PV industry calls for minimizing the material loses (kerf) during Si wafer slicing. The currently employed abrasive slicing methods are capable of slicing ~ 350 μm thick wafers. Recent research efforts have put forward wire-EDM as a potential method. This work presents an extensive experimentation to understand the parametric effects that give ultra thin wafer while minimizing the kerf-loss and maximizing the slicing rate. Ultra thin wafers of size 130–150 μm were fabricated using wire-EDM while controlling the input energy by avoiding wire or wafer breakage. The kerf-loss was reduced by ~ 50% (121 μm) while maintaining a high slicing rate of 1.05 mm/min. A typical wafer and associated kerf profiles showed a wider thickness at the entry and exit than the middle of the wafer. An increase in open voltage and a decrease in servo voltage increase the slicing rate in frontal direction and cause a decrease in slicing rate in the lateral direction, consequently decreasing the kerf-loss.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Machining and Optimization Techniques · Advanced Surface Polishing Techniques · Integrated Circuits and Semiconductor Failure Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. Study of electrical discharge machining technology for slicing silicon ingots10.1016/S0924-0136(03)00718-0 ↗
2. A vision for crystalline silicon photovoltaics10.1002/pip.709 ↗
3. Surface texture analysis of fixed and free abrasive machining of silicon substrates for solar cells
4. Study on removal mechanism of fixed-abrasive diamond wire saw slicing monocrystalline silicon
5. Study on silicon-slicing technique using plasma-etching processing10.1016/j.solmat.2008.09.052 ↗
6. Modeling of a single resistance capacitance pulse discharge in micro-electro discharge machining10.1115/1.2034512 ↗
7. Experimental investigation of wire electrical discharge machining of gallium-doped germanium10.1016/j.jmatprotec.2007.06.038 ↗
8. The effect of heterogeneous second phase on the machinability evaluation of spheroidal graphite cast irons in the WEDM process10.1016/j.matdes.2008.03.026 ↗
9. Fatigue response of Udimet 720 following minimum damage wire electrical discharge machining10.1016/j.matdes.2012.06.003 ↗
10. Crystallography, compositions, and properties of white layer by wire electrical discharge machining of nitinol shape memory alloy10.1016/j.matdes.2016.07.063 ↗
11. Investigation of silicon wafering by wire EDM10.1007/BF01119742 ↗
12. Improvement of EDM efficiency of silicon single crystal through ohmic contact10.1016/S0141-6359(99)00041-0 ↗
13. Uno · 2002
14. Cutting of polished single-crystal silicon by wire electrical discharge machining10.1016/j.precisioneng.2003.12.002 ↗
15. High-quality cutting of polished single-crystal silicon by wire electrical discharge machining10.1016/j.precisioneng.2004.12.004 ↗
16. Study of wire electrical discharge machining for poly-silicon
17. Response surface analysis of slicing of silicon ingots with focus on photovoltaic application10.1080/10910344.2012.731952 ↗
18. Multi-objective optimization for silicon wafer slicing using wire-EDM process10.1016/j.mssp.2015.06.050 ↗
19. Surface characteristics and damage of monocrystalline silicon induced by wire-EDM10.1016/j.apsusc.2014.09.074 ↗
20. High efficiency slicing of low resistance silicon ingot by wire electrolytic-spark hybrid machining10.1016/j.jmatprotec.2008.07.029 ↗
21. Interactions of efficiency and material requirements for terrestrial silicon solar cells10.1109/TCHMT.1980.1135653 ↗
22. Evaluations of spark distribution and wire vibration in wire EDM by high-speed observation10.1016/j.cirp.2010.03.073 ↗
23. The effects of machining settings on the behavior of pulse trains in the WEDM process10.1016/S0924-0136(97)82076-6 ↗
24. Montgomery · 2008
25. Modelling and analysis of the wire-tool vibration in wire-cut EDM10.1016/S0924-0136(03)00280-2 ↗
26. Modeling, simulation and parametric optimization of wire EDM process using response surface methodology coupled with grey-Taguchi technique10.4314/ijest.v2i5.60144 ↗
27. Evaluation of WEDM performance characteristics of Inconel 706 for turbine disk application10.1016/j.matdes.2015.09.036 ↗
28. Advancing EDM through fundamental insight into the process10.1016/S0007-8506(07)60020-1 ↗
29. Di · 2009
30. Minitab Inc. · 2010 · 1
31. Simultaneous optimization of several response variables10.1080/00224065.1980.11980968 ↗