Improving bonding quality of underwater friction stitch welds by selecting appropriate plug material and welding parameters and optimizing joint design
Source abstract
Abstract
Abstract Friction stitch welding of S355 steel was conducted under wet conditions to study the bonding quality. The effects of plug material, joint design, and welding variables on the weld defects, microstructural characteristics, hardness levels, and tensile properties were investigated. The underwater stitch welding performed with a S355 steel plug exhibited visible bonding defects at the weld interface, while the weld with LF2 as the plug material yielded a qualified joint without cracks or discontinuities, provided the plug and hole geometries were well-designed. The LF2-plug-stitch weld contained more upper bainite and fewer lath martensite grains, which was consistent with the substantially decreased hardness values in the weld metal. The joint was designed with large initial contact area and gap between the plug and hole, so a higher amount of heat was generated when welding was started. Further, the welding time was extended from 11 to 16 s, resulting in a larger heat affected zone and the flow of the plasticized (or squeezed) material was improved too. Stitch welds realized with a 40 kN forging force exhibited better ultimate tensile strength and elongation than those with a 35 kN forging force, when the other conditions were kept constant.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. Stephen · 1994
2. Investigation on Dissimilar Underwater Friction Stir Lap Welding of 6061-T6 Aluminum Alloy to Pure Copper10.1016/j.matdes.2014.07.036 ↗
3. Microstructural Characterizations and Mechanical Properties in Underwater Friction Stir Welding of Aluminum and Magnesium Dissimilar Alloys10.1016/j.matdes.2014.09.046 ↗
4. Underwater Repair by Friction Stitch Welding
5. Nicholas · 1995 · 11 · 7
6. Pauly · 1999
7. The Need for Gas Shielding — Positive Advantages for Two Friction Processes
8. Evaluation of Discontinuities in A36 Steel Repairs with Friction Hydro Pillar Processing Using Different Axial Forces10.2355/isijinternational.53.2269 ↗
9. Material Flow Influence on the Weld Formation and Mechanical Performance in Underwater Friction Taper Plug Welds for Pipeline Steel10.1016/j.matdes.2015.09.123 ↗
10. Pinheiro · 2008
11. Meyer · 2003
12. Fracture Toughness of Friction Hydro-Pillar Processing Welding in C–Mn Steel10.1016/j.matdes.2011.07.056 ↗
13. He · 2014
14. Investigations of Underwater FHPP for Welding Steel Overlap Joints10.1016/S1644-9665(12)60212-X ↗
15. Numerical Simulation of the Effects of Various Stud and Hole Configurations on Friction Hydro-Pillar Processing
16. Study of Microstructural Evolution of Friction Taper Plug Welded Joints of C–Mn Steels10.1179/136217110X12720264008556 ↗
17. Experimental Study of Friction Taper Plug Welding for Low Alloy Structure Steel: Welding Process, Defects, Microstructures and Mechanical Properties10.1016/j.matdes.2014.05.026 ↗
18. Friction Welding of Titanium and SUS 304 L Austenitic Stainless Steel10.1080/09507119009452178 ↗
19. Process Parameter Influence on Performance of Friction Taper Stud Welds in AISI 4140 Steel10.1016/j.matdes.2011.02.001 ↗
20. Residual Stresses in Overlapping Friction Taper Stud Welds. Proceedings of MECA-SENS 5, fifth international conference on mechanical stress evaluation by neutrons and synchrotron radiation, Mito, Japan, 10–12 November, 200910.4028/www.scientific.net/MSF.652.111 ↗
21. SA-6/SA-6M — Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling. ASME BPVC Section II: ASME. 2001
22. The Stress-relief Cracking Susceptibility of a New Ferritic Steel — Part 1: Single-pass Heat Affected Zone Simulations
23. Temperature Distribution for a Friction Taper Stud Weld in Thick Wall 10CrMo910 Steel
24. Classification and Quantification of Microstructures in Steels10.1179/026708304225010325 ↗
25. Hole Repair in Steel Plate Using Friction Taper Plug Welding — Initial Trials in Air and Underwater