Effect of original layer thicknesses on the interface bonding and mechanical properties of Ti Al laminate composites
Source abstract
Abstract
Abstract It is of great significance in high-temperature aeroengine applications for large-surface-area Ti Al laminate composites to be fabricated into Ti-Al3Ti parts by plastic forming and subsequent vacuum hot pressing. Then the original layer thicknesses have an important influence on the interface bonding and mechanical properties of Ti Al laminate composites, but only few reports about it have been published so far. In the present study, vacuum hot pressing was employed to fabricate Ti Al laminate composites using Ti and Al foils of different thickness. The resulting interface bond and mechanical properties of Ti Al laminate composites were then studied to determine the optimum sheet configuration and thickness. To further assess their formability and develop a forming limit diagram (FLD), 0.1/0.15 Ti Al laminate composites were operated on bending and forming tests to provide guidance for subsequent plastic forming of complex geometries. The results indicated that hot pressed laminates composed of alternating 0.1 (Al) and 0.15 (Ti) mm thick sheets exhibited enhanced superior interface bonding and mechanical properties compared with 0.2/0.25 and 0.4/0.4 sheets. The 0.1/0.15 Ti Al laminate composites had excellent bending characteristics and reasonable formability. Fabrication of a drawn cup further confirms the potential for hot pressed Ti Al laminate composites to be fabricated into complex shapes.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · MXene and MAX Phase Materials · Advanced Welding Techniques Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (22)
Show source-provided references
1. TiAl-based alloys: present status and future perspectives
2. Advances in gamma titanium aluminides and their manufacturing techniques10.1016/j.paerosci.2012.04.001 ↗
3. Microstructure and mechanical properties of Al/Ti/Al laminated composites prepared by roll bonding10.1016/j.msea.2015.03.086 ↗
4. Hot working behavior and processing map of a γ-TiAl alloy synthesized by powder metallurgy10.1016/j.matdes.2011.06.003 ↗
5. An investigation on microstructural and mechanical properties of powder metallurgical TiAl alloy during hot pack-rolling10.1016/j.msea.2014.09.091 ↗
6. Experimental study on warm roll bonding of metal/polymer/metal multilayer composites10.1016/j.jmatprotec.2015.02.040 ↗
7. Energy balance during explosive welding10.1016/j.jmatprotec.2015.03.024 ↗
8. Cladding of titanium and magnesium alloy plates using energy-controlled underwater three layer explosive welding10.1016/j.jmatprotec.2014.11.032 ↗
9. Microstructure and mechanical properties of Ti/Al explosive cladding10.1016/j.matdes.2013.12.012 ↗
10. Low-temperature plasma nitriding of titanium layer on Ti/Al clad sheet10.1016/j.matdes.2012.11.029 ↗
11. Structural and mechanical properties of metallic-intermetallic laminate composites produced by explosive welding and annealing10.1016/j.matdes.2011.09.030 ↗
12. Influence of Ti-TiN multilayer PVD-coatings design on residual stresses and adhesion10.1016/j.matdes.2015.03.007 ↗
13. Fabrication of Ti-Al3Ti core-shell structured particle reinforced Al based composite with promising mechanical properties10.1016/j.msea.2015.05.015 ↗
14. Effect of multi-pass friction stir processing on microstructure and mechanical properties of Al3Ti/A356 composites, materials characterization10.1016/j.matchar.2015.05.019 ↗
15. Influence of cooling rate on microstructure formation during rapid solidification of binary TiAl alloys10.1016/j.jallcom.2015.03.016 ↗
16. Mechanical properties of Ti-(Al3Ti+Al) and Ti/Al3Ti laminated composites
17. Tensile and flexural properties of multilayered metal/intermetallics composites10.1016/j.matchar.2015.02.018 ↗
18. Nanocrystalline matrix Al3Ni2-Al-Al3Ni composites produced by reactive hot-pressing of milled powders10.1016/j.intermet.2014.06.012 ↗
19. Fabrication and mechanical properties of TiBw/Ti-Ti(Al) laminated composites10.1016/j.matdes.2015.10.025 ↗
20. Characterization of the diffusion bonding behavior of pure Ti and Ni with different surface roughness during hot pressing10.1016/j.matdes.2014.09.071 ↗
21. Enhancement of bending formability of brittle sheet metal in multilayer metallic sheets10.1016/j.cirp.2010.03.109 ↗
22. Fracture behavior of Ti/Al3Ti metal-intermetallic laminate (MIL) composite under dynamic loading10.1016/j.msea.2015.04.025 ↗