Dynamic mechanical behavior of K417G superalloy: development of Johnson-Cook constitutive model and its application in single-grit grinding
Source abstract
Abstract
• A high-precision K417G Johnson-Cook constitutive model ( r ≥ 0.954, δ ≤ 7.9%) is built. • The model offers basis for K417G grinding simulation and process optimization. • a gmax affects K417G’s grinding force, chip morphology and residual stress over v s . • When a gmax increases from 1 to 5 μm, residual stress depth expands from 2.5 to 7.5 μm. • As a gmax increases, surface quality deteriorates, and obvious defects appear. The precision grinding of K417G superalloy, a key material for hot-end components of aero-engines, is plagued by large grinding forces and excessive heat generation. Clarifying the material removal mechanism is a prerequisite for optimizing the grinding process. Although single-grit grinding is a critical method for revealing this mechanism, it suffers from bottlenecks, such as the difficult acquisition of force or stress fields and poor process visualization. Finite element simulation, an alternative approach, cannot be practically applied because of the lack of dynamic mechanical properties data and a suitable constitutive model for K417G. This study systematically investigates the dynamic mechanical behavior of K417G and develops a Johnson-Cook constitutive model with high fitting accuracy. After embedding this model into single-grit grinding simulations, the study further quantifies the effects of undeformed chip thickness and grinding speed on material removal behavior. The results show that the undeformed chip thickness significantly affects the grinding force, chip morphology, and residual stress. This study not only provides a reliable constitutive basis for the simulation modeling of the precision grinding of K417G but also offers key theoretical support for the accurate optimization of grinding processes for aero-engine hot-end components, which has important engineering application value.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced machining processes and optimization · Advanced Surface Polishing Techniques · Mineral Processing and Grinding
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (92)
Show source-provided references
1. Cracking, microstructure and tribological properties of laser formed and remelted K417G Ni-based superalloy10.3390/coatings9020071 ↗
2. Tensile, creep behavior and microstructure evolution of an as-cast Ni-based K417G polycrystalline superalloy10.1016/j.jmst.2018.02.007 ↗
3. Effect of N content on microsegregation, microstructure and mechanical property of cast Ni-base superalloy K417G10.1016/j.msea.2017.06.044 ↗
4. Challenges and solutions for high-efficiency-sustainable grinding of aero-engine hot-end components10.1016/j.cja.2025.103536 ↗
5. Overcoming challenges: advancements in cutting techniques for high strength-toughness alloys in aero-engines10.1088/2631-7990/ad8117 ↗
6. Review of vibration texturing10.1016/j.jmatprotec.2025.118851 ↗
7. Temperature field model in surface grinding: a comparative assessment
8. Eco-friendly grinding: a bibliometric and knowledge map analysis10.1186/s10033-025-01198-7 ↗
9. Characterization and analysis of Inconel 718 alloy ground at different speeds10.1186/s10033-024-01017-5 ↗
10. Towards sustainable grinding of difficult-to-cut alloys—A holistic review and trends10.1186/s10033-024-01002-y ↗
11. Thermal management in grinding of superalloys – a critical review
12. Effects of grain refinement on the microstructure and tensile behavior of K417G superalloy10.1016/j.msea.2014.11.041 ↗
13. Single grain grinding: a novel approach to model the interactions at the grain/bond interface during grinding10.1007/s00170-020-05219-8 ↗
14. A grinding force prediction model for SiCp/Al composite based on single-abrasive-grain grinding10.1007/s00170-020-05638-7 ↗
15. Single grain grinding: an experimental and FEM assessment10.1016/j.procir.2016.07.082 ↗
16. Modification of strain rate strengthening coefficient for Johnson-Cook constitutive model of Ti6Al4V alloy
17. A modified Johnson–Cook constitutive model for titanium alloy TA31 and its implementation into FE10.1515/mt-2022-0371 ↗
18. The mechanics of cutting: in-situ measurement and modelling10.1016/j.procir.2015.03.048 ↗
19. Friction model for tool/work material contact applied to surface integrity prediction in orthogonal cutting simulation10.1016/j.procir.2017.03.229 ↗
20. Advances in material and friction data for modelling of metal machining10.1016/j.cirp.2017.05.002 ↗
21. Numerical and empirical modelling of machining-induced residual stresses in ball end milling of Inconel 71810.1016/j.procir.2017.03.177 ↗
22. Simulated and experimental analysis on serrated chip formation for hard milling process10.1016/j.jmapro.2019.06.018 ↗
23. Constitutive modelling and microstructural analysis of 92W-5Co-3Ni alloy subjected to high strain rate testing at elevated temperatures10.1016/j.matdes.2025.114035 ↗
24. Zhang · 2017
25. A creep constitutive model for Inconel 718-BNi2 brazed joints incorporating the dynamic interplay between dislocations and γ’’ precipitate phases10.1016/j.matdes.2025.114170 ↗
26. A review of constitutive models and thermal properties for nickel-based superalloys across machining-specific regimes10.1115/1.4056749 ↗
27. The state of the art for numerical simulations of the effect of the microstructure and its evolution in the metal-cutting processes10.1016/j.ijmachtools.2022.103890 ↗
28. Finite element simulation-based predictive regression modeling and optimum solution for grain size in machining of Ti6Al4V alloy: Influence of tool geometry and cutting conditions10.1016/j.simpat.2020.102141 ↗
29. New in situ imaging-based methodology to identify the material constitutive model coefficients in metal cutting process10.1115/1.4044251 ↗
30. G.R. Johnson, W.H. Cook, A Constitutive Model And Data For Metals, in: Proceedings of the 7th International Symposium on Ballistics, Hague, 1983: pp. 541–547.
31. A review on Johnson Cook material model10.1016/j.matpr.2022.04.279 ↗
32. On the prediction of the flow behavior of metals and alloys at a wide range of temperatures and strain rates using Johnson–Cook and modified Johnson–Cook-based models: a review10.3390/ma16041574 ↗
33. The Johnson Cook model for the machinability study10.1016/j.matpr.2023.02.371 ↗
34. Dynamic constitutive relationship of TiZrHfCu0.5 high entropy alloy based on Johnson-Cook model10.1016/j.jmrt.2023.10.154 ↗
35. Finite element modeling and cutting simulation of Inconel 71810.1016/j.cirp.2007.05.017 ↗
36. Plastic flow behavior of Inconel 718 under dynamic shear loads10.1016/j.ijimpeng.2007.03.005 ↗
37. Dynamic behavior and a modified Johnson–Cook constitutive model of Inconel 718 at high strain rate and elevated temperature10.1016/j.msea.2013.05.062 ↗
38. N. Kotkunde, H.N. Krishnamurthy, P. Puranik, A.K. Gupta, S.K. Singh, Microstructure study and constitutive modeling of Ti–6Al–4V alloy at elevated temperatures, Mater. Des. (1980-2015) 54 (2014) 96–103. https://doi.org/10.1016/j.matdes.2013.08.006.10.1016/j.matdes.2013.08.006 ↗
39. Determination of material constitutive laws for Inconel 718 superalloy under different strain rates and working temperatures10.1007/s11665-017-3017-8 ↗
40. Microstructure characteristics and comparative analysis of constitutive models for flow stress prediction of Inconel 718 alloy10.1007/s11665-019-04116-w ↗
41. Investigation of tensile Johnson-Cook model parameters for Nimonic 80A superalloy10.1016/j.jallcom.2019.06.153 ↗
42. Study on constitutive model and deformation mechanism in high speed cutting Inconel71810.1016/j.acme.2018.11.009 ↗
43. Residual stresses prediction in machining of Inconel 718 superalloy using a constitutive model considering the state of stress10.1016/j.procir.2020.02.029 ↗
44. Determination of Johnson Cook parameters for Ti-6Al-4 V Grade 5 experimentally by using three different methods10.1016/j.matpr.2020.11.825 ↗
45. The modified constitutive model considering strain-temperature coupling and dynamic recrystallization effective for FEM simulation of milling process10.1007/s00170-021-08243-4 ↗
46. The modified Johnson-Cook strain-stress constitutive model according to the deformation behaviors of a Ni-W-Co-C alloy10.1016/j.jmrt.2022.07.053 ↗
47. Research on parameter identification of Johnson–Cook constitutive model for TC17 titanium alloy cutting simulation
48. A modified Johnson-Cook constitutive model of Inconel 690 weld overlay taking into account the strain rate softening effect
49. Dynamic mechanical properties and modified johnson-cook model considering recrystallization softening for nickel-based powder metallurgy superalloys10.3390/ma17030670 ↗
50. Correction of the constitutive model and analysis of chip formation in cryogenic machining of TA15 titanium alloy10.1016/j.jmapro.2024.01.058 ↗
51. Dynamic constitutive modeling and adiabatic shear behavior of Ti-6Al-4V alloy under low-temperature impact loading10.1016/j.jmapro.2025.04.008 ↗
52. Finite-element simulation of wave propagation and dispersion in Hopkinson bar test10.1016/j.matdes.2004.08.021 ↗
53. A comparative study on Johnson-Cook and modified Johnson-Cook constitutive material model to predict the dynamic behavior laser additive manufacturing FeCr alloy10.1016/j.jallcom.2017.06.251 ↗
54. Mechanical properties and dynamic constitutive model of 42CrMo steel10.1016/j.matdes.2017.01.066 ↗
55. A constitutive model for Ti6Al4V considering the state of stress and strain rate effects10.1016/j.mechmat.2019.103103 ↗
56. Influence of microstructural and loading direction on the ductility and anisotropy of Ni-based superalloys10.1016/j.matdes.2024.113342 ↗
57. Harnessing instability for work hardening in multi-principal element alloys10.1038/s41563-024-01871-7 ↗
58. The effects of carbon content on the microstructure and elevated temperature tensile strength of a nickel-base superalloy10.1016/j.msea.2010.03.053 ↗
59. Deformation behavior, constitutive modeling and microstructure evolution of 2195 Al-Li alloy deformed at high strain rates and cryogenic temperatures10.1016/j.matdes.2024.113100 ↗
60. Kinetics of flow and strain-hardening10.1016/0001-6160(81)90112-7 ↗
61. Additive manufacturing of stainless steel-to-inconel graded material: Insights into microstructure, defects, and mechanical properties10.1016/j.matdes.2025.114469 ↗
62. Temperature-dependent deformation behavior of γ and γ′ single-phase nickel-based superalloys10.1016/j.msea.2021.141439 ↗
63. Dynamic deformation mechanism for distinct flow behaviors in FGH4113A superalloy with high γ′ content during isothermal compression at sub-/near-/super-solvus temperatures10.1016/j.matdes.2024.112890 ↗
64. Inverse identification of the constitutive equation of Inconel 718 and AISI 1045 from FE machining simulations10.1016/j.procir.2013.06.091 ↗
65. Determination of Johnson–Cook parameters and evaluation of Charpy impact test performance for X80 pipeline steel10.1016/j.ijmecsci.2020.105627 ↗
66. Distribution estimation of Johnson-Cook parameters considering correlation in quasi-static state10.1016/j.ijmecsci.2022.108086 ↗
67. On the calibration strategies of the Johnson–Cook strength model: Discussion and applications to experimental data10.1016/j.msea.2014.05.006 ↗
68. On the accuracy of the johnson-cook constitutive model for metals
69. Artificial neural network modelling to predict hot deformation behaviour of as HIPed FGH4169 superalloy10.1179/1743284713Y.0000000411 ↗
70. On establishment of novel constitutive model for directionally solidified nickel-based superalloys utilizing machine learning methods10.1007/s41230-023-3028-z ↗
71. Comparative investigation on grindability of K4125 and Inconel718 nickel-based superalloys10.1007/s00170-018-1993-y ↗
72. Material removal mechanisms in ultrasonic vibration-assisted high-efficiency deep grinding γ-TiAl alloy10.1016/j.cja.2024.01.021 ↗
73. The prediction of friction and wear when a soft surface slides against a harder rough surface10.1016/0043-1648(95)06830-9 ↗
74. Probabilistic Analysis of the Surface Grinding Process10.1139/tcsme-1984-0031 ↗
75. Study of cutting deformation in machining nickel-based alloy Inconel 71810.1016/j.ijmachtools.2011.02.011 ↗
76. Plastic deformation mechanism of grinding subsurface of nickel-based single-crystal superalloy10.1007/s00170-023-12240-0 ↗
77. Investigation on size effect of grain wear behavior during grinding nickel-based superalloy Inconel 71810.1007/s00170-016-9907-3 ↗
78. The influence of speed on material removal mechanism in high speed grinding with single grit10.1016/j.ijmachtools.2014.11.010 ↗
79. Modeling and simulation of chip-flow in grinding of different materials – AlMg5 and C45
80. Coupled thermo-mechanical analysis and optimization of the grinding process for Inconel 718 superalloy using single grit approach10.1016/j.triboint.2022.107530 ↗
81. Grinding surface and subsurface stress load of nickel-based single crystal superalloy DD510.1016/j.precisioneng.2024.02.017 ↗
82. Episodes of chip formation in micro-to-nanoscale cutting of Inconel 62510.1016/j.ijmecsci.2021.106407 ↗
83. Grinding subsurface damage mechanism of nickel-based single crystal superalloy based on stress-strain10.1016/j.precisioneng.2023.11.001 ↗
84. Study on chip formation in grinding of nickel-based polycrystalline superalloy GH416910.1007/s00170-022-09386-8 ↗
85. An investigation on material removal mechanism in ultra-high-speed grinding of nickel-based superalloy: three-dimensional simulation and experimental verification10.1007/s00170-020-05922-6 ↗
86. Study on surface integrity and material removal mechanism in eco-friendly grinding of Inconel 718 using numerical and experimental investigations10.1007/s00170-020-06528-8 ↗
87. Experimental and simulation-based investigation of serrated chip formation in high-speed milling of Inconel 71810.1007/s00170-025-16130-5 ↗
88. Finite element modeling for serrated chip formation and microstructure analysis of machined surface layer in high-speed milling of Inconel 718
89. Understanding the effects of grinding speed and undeformed chip thickness on the chip formation in high-speed grinding10.1007/s00170-015-7265-1 ↗
90. Simulation research on the grinding forces and stresses distribution in single-grain surface grinding of Ti-6Al-4V alloy when considering the actual cutting-depth variation10.1007/s00170-017-0084-9 ↗
91. A modified constitutive model coupled with microstructure evolution incremental model for machining of titanium alloy Ti–6Al–4V10.1016/j.jmatprotec.2021.117262 ↗
92. Modelling of serrated chip formation processes using the stabilized optimal transportation meshfree method10.1016/j.ijmecsci.2019.03.005 ↗