journal article·2025-02Open access

Mechanical properties and microstructure of wire laser metal deposited austenitic stainless steel

P. Kyvelou, W. Hong, R. Zhang, L. Gardner

Materials & Design· Volume 250

Abstract

Laser metal deposition (LMD) is a metal 3D printing method that enables the efficient and cost-effective production of large-scale components, rendering it increasingly attractive for civil engineering applications. However, the scarcity of data and lack of knowledge of the material response and geometric variability of LMD steels is inhibiting adoption of this manufacturing method in the construction industry. To address this, a comprehensive experimental investigation into the geometry, mechanical properties and microstructural characteristics of LMD plates made from ER 308LSi stainless steel has been carried out and is presented herein. Laser scanning, tensile testing and microstructural analyses were conducted on a series of coupons of different thicknesses (2 mm and 8 mm), printing strategies, surface conditions and orientations. The results indicated low geometric irregularity, with both as-built and machined coupons displaying nearly identical mechanical properties. The thinner specimens had lower strengths, mainly attributed to their larger grain sizes. Significant anisotropy was observed from the mechanical tests on the thinner specimens, explained by a strong crystallographic texture observed in the microstructure. Overall, the examined material exhibited good mechanical behaviour and geometric consistency. Finally, a constitutive modelling approach previously applied to wire arc additively manufactured (WAAM) stainless steel was successfully adapted to characterise the anisotropic behaviour of LMD stainless steel in both the elastic and inelastic material ranges. The findings highlight the potential for using LMD in construction, offering a viable means of fabricating large-scale metal components with sound mechanical performance.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (70)

Show source-provided references
1. (2023) Metal additive manufacturing in structural engineering – review, advances, opportunities and outlook10.1016/j.istruc.2022.12.039 ↗
2. Environmental life cycle assessment of wire arc additively manufactured structural components10.1016/j.jclepro.2023.136071 ↗
3. Meng X, Gardner L. Hybrid construction featuring wire arc additive manufacturing: review, concepts, challenges and opportunities. Engineering Structures. [Submitted].
4. Role of metal 3D printing to increase quality and resource-efficiency in the construction sector
5. Laser metal deposition and wire arc additive manufacturing of materials: An overview10.24425/amm.2019.127561 ↗
6. Fatigue strengthening of damaged steel members using wire arc additive manufacturing10.1016/j.engstruct.2023.115911 ↗
7. Experimental study of DED-arc additively manufactured steel double-lap shear bolted connections10.1016/j.engstruct.2023.115736 ↗
8. Tensile behaviour of WAAM high strength steel material and members10.1016/j.matdes.2023.112517 ↗
9. An end-to-end framework for the additive manufacture of optimized tubular structures10.1109/ACCESS.2021.3132797 ↗
10. Testing and Analysis of Optimized Wire Arc Additively Manufactured Steel Trusses10.1061/JSENDH.STENG-12832 ↗
11. I-section steel columns strengthened by wire arc additive manufacturing - concept and experiments10.1016/j.engstruct.2024.117763 ↗
12. Blended structural optimization for wire-and-arc additively manufactured beams10.1007/s40964-022-00335-1 ↗
13. Material properties and local stability of WAAM stainless steel equal angle sections10.1016/j.engstruct.2023.116160 ↗
14. Chen MT, Y, Zuo W, Yun X, Zhao O, Liu SW, Xu F. Experimental investigation on the tensile behavior of wire arc additively manufactured duplex stainless steel plates. Engineering Structures. 2024; 321: 118764.10.1016/j.engstruct.2024.118764 ↗
15. Mechanical behavior of austenitic stainless steels produced by wire arc additive manufacturing10.1016/j.tws.2023.111455 ↗
16. Behaviour and design of stainless steel I-section columns in fire10.1016/j.jcsr.2019.105890 ↗
17. Experimental and numerical studies of ferritic stainless steel cross-sections under combined compression and bending10.1061/(ASCE)ST.1943-541X.0001366 ↗
18. Material and local buckling response of ferritic stainless steel sections10.1016/j.tws.2014.12.012 ↗
19. Research status of laser additive manufacturing for metal: a review10.1016/j.jmrt.2021.08.050 ↗
20. Additive manufacturing of metallic components - Process, structure and properties10.1016/j.pmatsci.2017.10.001 ↗
21. Gibson · 2014
22. A Review on Wire-Laser Directed Energy Deposition: Parameter Control, Process Stability, and Future Research Paths10.3390/jmmp8020084 ↗
23. Additive manufacturing for the aerospace industry
24. Additive manufacturing in the aerospace and automotive industries: Recent trends and role in achieving sustainable development goals10.1016/j.asej.2023.102516 ↗
25. Enhancing biocompatible metal alloy fabrication for bio implants through laser-based additive manufacturing (LBAM)10.1016/j.bioana.2024.02.001 ↗
26. 3D Printing Technologies in Metallic Implants: A Thematic Review on the Techniques and Procedures10.18063/ijb.v7i1.306 ↗
27. Performance of laser metal deposition on hot-rolled stainless steel for hybrid steel structures10.1016/j.conbuildmat.2024.137744 ↗
28. Additive Manufacturing in Off-Site Construction: Review and Future Directions10.3390/buildings12010053 ↗
29. A review of WAAM for steel construction-Manufacturing, material and geometric properties, design, and future directions10.1016/j.istruc.2022.08.084 ↗
30. Experimentally-validated orthotropic elastic model for Wire-and-Arc Additively Manufactured stainless steel
31. On the influence of the geometrical irregularities in the mechanical response of wire-and-arc additively manufactured planar elements10.1016/j.jcsr.2020.106490 ↗
32. Influence of the printing strategy on the microstructure and mechanical properties of thick-walled wire arc additive manufactured stainless steels
33. Laser additive manufacturing of metallic components: materials, processes and mechanisms10.1179/1743280411Y.0000000014 ↗
34. Meltio. Wire-Laser Metal 3D printing. https://meltio3d.com/ [Accessed 2nd September 2024].
35. Iso · 2019
36. Mechanical and microstructural testing of wire and arc additively manufactured sheet material10.1016/j.matdes.2020.108675 ↗
37. Mechanical testing and microstructural analysis of wire arc additively manufactured steels10.1016/j.matdes.2022.110544 ↗
38. Oqton, Inc, Geomagic Wrap 2017, https://www.oqton.com/geomagic-wrap, Version 2017.0.2:64.
39. Robert McNeel & Associates, Rhino 6, https://www.rhino3d.com/, Version 6.
40. Mechanical properties and microstructure of additively manufactured stainless steel with laser welded joints10.1016/j.matdes.2021.109921 ↗
41. ASTM E3-11:2017. Standard Guide for Preparation of Metallographic Specimens., West Conshohocken, PA: American Society for Testing and Materials; 2017.
42. Bruker Corporation, ESPRIT, https://www.bruker.com/en/products-and-solutions/elemental-analyzers/eds-wds-ebsd-SEM-Micro-XRF/software-esprit-family.html,Version 2.3.
43. Texture analysis with MTEX–free and open source software toolbox10.4028/www.scientific.net/SSP.160.63 ↗
44. ASTM E2627-23. Standard practice for determining average grain size using electron backscatter diffraction (EBSD) in fully polycrystalline materials. Technical Report, West Conshohocken, PA: ASTM International; 2013.
45. Iso · 2018
46. Ramberg W, Osgood WR. Description of stress-strain curves by three parameters. Technical Note No. 902, National Advisory Committee for Aeronautics. Washington, D.C., USA; 1943.
47. Full-range stress–strain curves for stainless steel alloys10.1016/S0143-974X(02)00018-4 ↗
48. LaVision GmbH, DaVis 10, https://www.lavision.de/en/products/davis-software/, Version 10.2.1.
49. Behaviour and design of stainless steel SHS and RHS beam-columns10.1016/j.tws.2016.04.018 ↗
50. Description of stress-strain curves for stainless steel alloys10.1016/j.matdes.2015.08.001 ↗
51. Full-range stress-strain curves for aluminum alloys10.1061/(ASCE)ST.1943-541X.0002999 ↗
52. En · 2006
53. EN 1993-1-1:2020. Eurocode 3 - Design of steel structures - Part 1-1: General rules and rules for buildings. Brussels: European committee for standardization; 2020.
54. Low cycle fatigue behaviour of wire arc additively manufactured ER70S-6 steel10.1016/j.ijfatigue.2023.107910 ↗
55. Fatigue testing and analysis of steel plates manufactured by wire-arc directed energy deposition
56. Microstructure, mechanical properties and cross-sectional behaviour of additively manufactured stainless steel cylindrical shells
57. Crystallographic-orientation-dependent tensile behaviours of stainless steel 316L fabricated by laser powder bed fusion10.1016/j.msea.2019.138395 ↗
58. Weaver JS, Rosenthal I. Understanding anisotropic tensile properties of laser powder bed fusion additive metals: a detailed review of select examples. US Department of Commerce, National Institute of Standards and Technology; 2021.10.6028/NIST.AMS.100-44 ↗
59. Measuring anisotropy in Young’s modulus of copper using microcantilever testing10.1557/jmr.2009.0396 ↗
60. Predicted monocrystal elastic constants of 304-type stainless steel10.1016/0378-4363(85)90076-2 ↗
61. Rotating bending fatigue behaviour and quasi‐static tensile properties of Wire Arc Additively Manufactured 308L stainless steel10.1002/cepa.2441 ↗
62. Effects of scanning pattern on the grain structure and elastic properties of additively manufactured 316L austenitic stainless steel10.1016/j.msea.2021.142447 ↗
63. Mechanical anisotropy of additively manufactured stainless steel 316L: An experimental and numerical study10.1016/j.msea.2020.140154 ↗
64. Effect of build geometry and orientation on microstructure and properties of additively manufactured 316L stainless steel by laser metal deposition10.1016/j.mtla.2019.100359 ↗
65. The deformation and ageing of mild steel: III discussion of results10.1088/0370-1301/64/9/303 ↗
66. The cleavage strength of polycrystals
67. On the anisotropy of thick-walled wire arc additively manufactured stainless steel parts
68. Description of anisotropic material response of wire and arc additively manufactured thin-walled stainless steel elements10.1016/j.tws.2021.108634 ↗
69. Hill R. A theory of the yielding and plastic flow of anisotropic metals. Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences. 1948; 193: 281-297.10.1098/rspa.1948.0045 ↗
70. Mechanik der plastischen Formänderung von Kristallen