journal article·2015-10

A new 1.9GPa maraging stainless steel strengthened by multiple precipitating species

Yongcan Li, Wei Yan, James D. Cotton, Glamm J. Ryan, Yifu Shen, Wei Wang, Yiyin Shan, Ke Yang

Materials & Design· Volume 82
Publisher page

Abstract

Abstract A new ultra-high strength maraging stainless steel with composition of 13Cr–13Co–4.5Ni–3.5Mo–0.5Ti (at.%) has been developed. It was demonstrated that the ultimate tensile strength of the steel could reach 1.9 GPa with reasonable ductility. This breakthrough was achieved by a combined strengthening of three different species of precipitates. The evolution of precipitates with respect of size, morphology and chemical composition during aging at 500 °C was characterized using atom probe tomography (APT) and transmission electron microscopy (TEM). The precipitates were identified to be η-phase Ni3(Ti, Al) phase, Mo-rich R′ phase and Cr-rich α′ phase, developing out of the precursor clusters, Ni–Ti–Al-rich cluster, Mo-rich cluster and Cr-rich cluster, separately. The segregation of Mo and Cr atoms at the precipitate/matrix interfaces was detected and is considered to impede the coarsening of η-phase. Based on the characterizations, the precipitation process of these phases and their effect on mechanical properties were analyzed.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Microstructure and Mechanical Properties of Steels · Advanced Materials Characterization Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. Microstructural evolution in a PH13-8 stainless steel after ageing10.1016/S1359-6454(02)00353-1 ↗
2. Aging reactions in a 17–4 PH stainless steel10.1016/S0254-0584(01)00460-6 ↗
3. The effect of ageing upon the microstructure and mechanical properties of type 15-5 PH stainless steel10.1016/S0921-5093(02)00062-X ↗
4. Splitting phenomenon in the precipitation evolution in an Fe–Ni–Al–Ti–Cr stainless steel10.1016/j.actamat.2009.10.030 ↗
5. Enhanced mechanical properties induced by refined heat treatment for 9 Cr–0.5 Mo–1.8 W martensitic heat resistant steel10.1016/j.matdes.2013.01.072 ↗
6. Precipitate modification in PH13-8 Mo type maraging steel10.1016/j.actamat.2011.04.053 ↗
7. Atom probe tomography investigation of lath boundary segregation and precipitation in a maraging stainless steel10.1016/j.ultramic.2012.10.014 ↗
8. Effect of Cu on the evolution of precipitation in an Fe–Cr–Ni–Al–Ti maraging steel10.1016/j.actamat.2010.03.010 ↗
9. Reverted austenite in PH 13–8 Mo maraging steels10.1016/j.matchemphys.2010.02.058 ↗
10. Microstructural evolution in 13Cr–8Ni–2.5Mo–2Al martensitic precipitation-hardened stainless steel10.1016/j.msea.2004.12.002 ↗
11. Isothermal formation of quasicrystalline precipitates and their effect on strength in a 12Cr–9Ni–4Mo maraging stainless steel10.1007/BF02652323 ↗
12. Quasicrystalline and crystalline precipitation during isothermal tempering in a 12Cr–9Ni–4Mo maraging stainless steel10.1016/0956-7151(94)00461-P ↗
13. On the Cu precipitation behavior in thermo-mechanically embrittlement processed low copper reactor pressure vessel model steel10.1016/j.matdes.2012.12.055 ↗
14. Precipitation in 18wt% Ni maraging steel of grade 35010.1016/S1359-6454(99)00370-5 ↗
15. Phase chemistry and precipitation reactions in maraging steels: Part IV. Discussion and conclusions10.1007/BF02668193 ↗
16. Recent developments in stainless steels10.1016/j.mser.2009.03.001 ↗
17. Ageing behaviour of an Fe–20Ni–1.8Mn–1.6Ti–0.59Al (wt%) maraging alloy: clustering, precipitation and hardening10.1016/j.actamat.2004.08.018 ↗
18. Effect of aging and deformation on the microstructure and properties of Fe–Ni–Ti maraging steel
19. Comparison of early stages of precipitation in Mo-rich and Mo-poor maraging stainless steels10.1002/sia.2514 ↗
20. A phase-field and electron microscopy study of phase separation in Fe–Cr alloys10.1016/j.msea.2011.12.007 ↗
21. The 475°C embrittlement in Fe–20Cr and Fe–20Cr–X (X= Ni, Cu, Mn) alloys studied by mechanical testing and atom probe tomography10.1016/j.msea.2013.03.016 ↗
22. Investigation on the crystallography of the transformation products of reverted austenite in intercritically reheated coarse grained heat affected zone10.1016/j.matdes.2012.07.015 ↗
23. Nanoscale austenite reversion through partitioning, segregation and kinetic freezing: example of a ductile 2.0GPa Fe–Cr–C steel10.1016/j.actamat.2012.01.045 ↗
24. Stability of retained austenite in multi-phase microstructure during austempering and its effect on the ductility of a low carbon steel10.1016/j.msea.2014.02.059 ↗
25. A new ultrahigh-strength stainless steel strengthened by various coexisting nanoprecipitates10.1016/j.actamat.2010.03.005 ↗
26. Genetic design and characterization of novel ultra-high-strength stainless steels strengthened by Ni3Ti intermetallic nanoprecipitates10.1016/j.actamat.2010.02.028 ↗
27. Age hardening and mechanical properties of a 2400MPa grade cobalt-free maraging steel
28. Atom probe studies of the Fe–Cr system and stainless steels aged at intermediate temperature: a review10.1016/S1044-5803(99)00048-0 ↗
29. Microstructure and mechanical properties of high-carbon Si–Al-rich steel by low-temperature austempering10.1016/j.matdes.2011.08.041 ↗
30. The influence of tempering temperature on the reversed austenite formation and tensile properties in Fe–13% Cr–4% Ni–Mo low carbon martensite stainless steels10.1016/j.msea.2011.01.078 ↗
31. Miller MK, Cerezo A, Hetherington M, Smith G. Atom probe field ion microscopy; 1996.10.1093/oso/9780198513872.001.0001 ↗
32. Atom probe tomography: a technique for nanoscale characterization10.1017/S1431927604040577 ↗
33. Efficient sampling for three-dimensional atom probe microscopy data10.1016/S0304-3991(02)00317-0 ↗
34. Dependence of interfacial excess on the threshold value of the isoconcentration surface10.1002/sia.1708 ↗
35. Precipitation process of martensitic PH stainless steel Nanoflex10.1179/1743284711Y.0000000115 ↗
36. Precipitation hardening in a 12%Cr–9%Ni–4%Mo–2%Cu stainless steel10.1016/j.actamat.2003.10.048 ↗
37. Role of severe plastic deformation on the formation of nanograins and nano-sized precipitates in Fe–Ni–Mn steel10.1016/j.matdes.2011.02.018 ↗
38. Austenite stability of ultrafine-grained transformation-induced plasticity steel with Mn partitioning10.1016/j.scriptamat.2011.04.010 ↗
39. The effect of morphology on the stability of retained austenite in a quenched and partitioned steel10.1016/j.scriptamat.2012.11.003 ↗
40. Copper precipitation and its impact on mechanical properties in a low carbon microalloyed steel processed by a three-step heat treatment10.1016/j.matdes.2014.05.059 ↗
41. Effect of external stress on the Fe–Cr phase separation in 15–5 PH and Fe–15Cr–5Ni alloys10.1016/j.ultramic.2012.12.004 ↗