Evaluation of mechanical and wear properties of Ti xNb 7Fe alloys designed for biomedical applications
Source abstract
Abstract
A group of Ti[sbnd]xNb[sbnd]7Fe (x = 0, 1, 4, 6, 9, 11 wt.%) alloys was designed and produced by cold crucible levitation melting process. The microstructural characteristic of the alloys with Nb addition and its effect on their mechanical properties as well as wear resistance were investigated. Microscopic and phase analysis results show that all the alloys, except for the Ti[sbnd]11Nb[sbnd]7Fe, exhibit orthorhombic α“ and body-centred cubic β phases, while Ti[sbnd]11Nb[sbnd]7Fe alloy consists of only β phase. It is proposed that increasing the Nb content enhances β phase stability and its proportion in the microstructure of the designed alloys. Depending on the proportion of β and α” phases, Ti[sbnd]xNb[sbnd]7Fe alloys show varied hardness (3.57–5.92 GPa) and compressive strength (1990–2093 MPa). Additionally, they present wear rates in the range of 3 × 10–1 × 10 m/m which correlates well with the changes in the corresponding microstructures and mechanical properties. Among the studied alloys, Ti[sbnd]11Nb[sbnd]7Fe with β phase microstructure, presents the lowest elastic modulus (86 GPa) and the highest compressive strain (41.5%) along with high compressive strength, hardness and wear resistance. Therefore, it is suggested that this β-type Ti[sbnd]11Nb[sbnd]7Fe alloy is a promising candidate, more suitable than the commercially used CP[sbnd]Ti and Ti[sbnd]6Al[sbnd]4V, for orthopedic applications.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Intermetallics and Advanced Alloy Properties · Magnesium Alloys: Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (65)
Show source-provided references
1. Structure and mechanical properties of as-cast Ti5NbxCr alloys10.1016/j.matdes.2013.04.001 ↗
2. Microstructure and mechanical properties of TiZrCr biomedical alloys10.1016/j.msec.2015.02.028 ↗
3. Characterization of a new beta titanium alloy, Ti12Mo3Nb, for biomedical applications10.1016/j.jallcom.2011.11.035 ↗
4. Effect of α″martensite on the microstructure and mechanical properties of beta-type TiFeTa alloys10.1016/j.matdes.2015.03.028 ↗
5. Corrosion behavior of selective laser melted Ti6Al4V alloy in NaCl solution10.1016/j.corsci.2015.10.041 ↗
6. Effect of commercial purity levels on the mechanical properties of ultrafine-grained titanium10.1016/j.msea.2010.11.021 ↗
7. Study on improved tribological properties by alloying copper to CPTi and Ti6Al4V alloy10.1016/j.msec.2015.07.046 ↗
8. Powder metallurgical low-modulus TiMg alloys for biomedical applications10.1016/j.msec.2015.06.010 ↗
9. Corrosion behavior of β titanium alloys for biomedical applications10.1016/j.msec.2011.02.005 ↗
10. Ti based biomaterials, the ultimate choice for orthopaedic implants—a review10.1016/j.pmatsci.2008.06.004 ↗
11. Selective laser melting of titanium alloys and titanium matrix composites for biomedical applications: a review10.1002/adem.201500419 ↗
12. Investigations into Ti(Nb, Ta)Fe alloys for biomedical applications
13. Fabrication of low-cost beta-type TiMn alloys for biomedical applications by metal injection molding process and their mechanical properties10.1016/j.jmbbm.2016.02.035 ↗
14. Tribocorrosion properties of different type titanium alloys in simulated body fluid10.1016/j.wear.2014.12.017 ↗
15. Microstructure, defects and mechanical behavior of beta-type titanium porous structures manufactured by electron beam melting and selective laser melting10.1016/j.actamat.2016.04.029 ↗
16. Microstructure and metallic ion release of pure titanium and Ti13Nb13Zr alloy processed by high pressure torsion10.1016/j.matdes.2015.11.088 ↗
17. Composition/phase structure and properties of titanium-niobium alloys10.2320/matertrans.44.2384 ↗
18. Wear characteristics of metallic biomaterials: a review10.3390/ma8052749 ↗
19. Surface modification of titanium, titanium alloys, and related materials for biomedical applications10.1016/j.mser.2004.11.001 ↗
20. Friction and wear behavior of titanium matrix (TiB+ TiC) composites10.1016/j.wear.2010.12.072 ↗
21. Comparison of wear properties of commercially pure titanium prepared by selective laser melting and casting processes10.1016/j.matlet.2014.11.156 ↗
22. A review on selective laser sintering/melting (SLS/SLM) of aluminium alloy powders: processing, microstructure, and properties10.1016/j.pmatsci.2015.03.002 ↗
23. Selective laser melting of in situ titanium–titanium boride composites: processing, microstructure and mechanical properties10.1016/j.actamat.2014.05.022 ↗
24. Microstructure and mechanical behavior of a Ti24Nb4Zr8Sn alloy processed by warm swaging and warm rolling10.1016/j.actamat.2012.01.003 ↗
25. Effect of Fe content on glass-forming ability and crystallization behavior of a (Ti 69.7 Nb 23.7 Zr 4.9 Ta 1.7) 100− xFex alloy synthesized by mechanical alloying10.1016/j.jallcom.2012.10.154 ↗
26. Biocompatibility of Ti-alloys for long-term implantation10.1016/j.jmbbm.2012.11.014 ↗
27. Duplex nitriding treatment of a beta-metastable Ti 94 Mo 6 alloy for biomedical applications10.1016/j.jallcom.2007.02.155 ↗
28. Ultrafine-grained Ti-based composites with high strength and low modulus fabricated by spark plasma sintering10.1016/j.msea.2012.09.047 ↗
29. Microstructures and properties of titanium alloys TiMo for dental use10.1016/S1003-6326(06)60308-7 ↗
30. Fatigue performance and cyto-toxicity of low rigidity titanium alloy, Ti29Nb13Ta4.6 Zr10.1016/S0142-9612(03)00069-3 ↗
31. Super-elastic titanium alloy with unstable plastic deformation10.1063/1.2037192 ↗
32. Effect of Nb addition on microstructure evolution and nanomechanical properties of a glass-forming TiZrSi alloy10.1016/j.intermet.2013.11.010 ↗
33. Electrochemical corrosion behavior and elasticity properties of Ti6AlxFe alloys for biomedical applications
34. Mechanical properties and microstructures of new TiFeTa and TiFeTaZr system alloys10.1016/j.msec.2005.04.004 ↗
35. Compatibility assessment of new V-free low-cost Ti–4.7 Mo–4.5 Fe alloy for some biomedical applications10.1016/j.matdes.2016.02.110 ↗
36. Effect of ball-milling time on the structural characteristics of biomedical porous TiSnNb alloy10.1016/j.msec.2011.02.011 ↗
37. Newly developed TiNbZrTaSiFe biomedical beta titanium alloys with increased strength and enhanced biocompatibility10.1016/j.msec.2015.11.043 ↗
38. Structure and mechanical properties of as-cast Ti5NbxFe alloys10.1016/j.matchar.2010.05.003 ↗
39. Influence of phase transformations on dynamical elastic modulus and anelasticity of beta TiNbFe alloys for biomedical applications10.1016/j.jmbbm.2015.02.030 ↗
40. Mechanical strength and biocompatibility of meta-stable[beta] type Ti-5 Fe-3 Nb-3 Zr for biomedical applications10.2320/jinstmet.76.397 ↗
41. Order-sintering of mechanically alloyed FeAl nanostructures10.1016/j.jallcom.2010.03.150 ↗
42. Structural evolution of Fe–50at.% Al powders during mechanical alloying and subsequent annealing processes10.1016/j.jallcom.2010.01.145 ↗
43. Glass formation in a (Ti, Zr, Hf)–(Cu, Ni, Ag)–Al high-order alloy system by mechanical alloying10.1557/JMR.2003.0300 ↗
44. Evaluation of the volume fraction of nanocrystals devitrified in Al-based amorphous alloys10.1016/j.jnoncrysol.2008.12.001 ↗
45. Structure and mechanical properties of Ti5Cr based alloy with Mo addition10.1016/j.msec.2010.04.006 ↗
46. Effect of Nb addition on microstructure, mechanical properties and castability of β-type TiMo alloys10.1016/S1003-6326(15)63834-1 ↗
47. Structure–property relationship of cast TiNb alloys10.1046/j.1365-2842.2002.00825.x ↗
48. Properties and structural characteristics of TiNbAl alloys10.1016/j.msea.2004.11.021 ↗
49. Influence of forging deformation and heat treatment on microstructure of TixNb3Zr2Ta alloys10.1016/j.msec.2011.10.006 ↗
50. Structure and properties characterization of ceramic coatings produced on Ti6Al4V alloy by microarc oxidation in aluminate solution10.1016/S0167-577X(01)00440-2 ↗
51. Development of high modulus TiFeCu alloys for biomedical applications10.2320/matertrans.M2012361 ↗
52. Phase transition, microstructural evolution and mechanical properties of TiNbFe alloys induced by Fe addition10.1016/j.matdes.2016.02.094 ↗
53. Mechanical response and effects of β-to-α″ phase transformation on the strengthening of Ti10V2Fe3Al during one-dimensional shock loading10.1016/j.msea.2012.10.098 ↗
54. Compressive deformation behaviors of coarse-and ultrafine-grained pure titanium at different temperatures: a comparative study10.2320/matertrans.M2011041 ↗
55. Compression testing of Ti6Al4V in the temperature range of 303–873K10.1080/10426910801937405 ↗
56. Numerical investigation of the effect of porous titanium femoral prosthesis on bone remodeling10.1016/j.matdes.2010.12.042 ↗
57. Mechanical and corrosion-resistant properties of TiNbSiN nanocomposite films prepared by a double glow discharge plasma technique10.1016/j.ceramint.2014.01.079 ↗
58. Nanostructured β-phase Ti–31.0 Fe–9.0 Sn and sub-μm structured Ti–39.3 Nb–13.3 Zr–10.7 Ta alloys for biomedical applications: microstructure benefits on the mechanical and corrosion performances10.1016/j.msec.2012.07.016 ↗
59. Effects of sliding velocity on tribo-oxides and wear behavior of Ti6Al4V alloy10.1016/j.triboint.2015.02.009 ↗
60. Dry-sliding tribological properties of ultrafine-grained Ti prepared by severe plastic deformation10.1016/j.actamat.2005.07.031 ↗
61. Transition between mild and severe wear in titanium alloys10.1016/j.triboint.2015.08.020 ↗
62. Dry sliding wear of Ti6Al4V alloy as influenced by the counterface and sliding conditions10.1016/S0043-1648(99)00292-6 ↗
63. Hydroxyapatite production on ultrafine-grained pure titanium by micro-arc oxidation and hydrothermal treatment10.1016/j.surfcoat.2011.03.032 ↗
64. Microstructure and sliding wear behavior of pure titanium surface modified by double-glow plasma surface alloying with Nb10.1016/j.matdes.2013.05.061 ↗
65. Mechanical and wear properties of ultrafine-grained pure Ti produced by multi-pass equal-channel angular extrusion10.1016/j.msea.2009.03.054 ↗