journal article·2025-12Open access

Deformation-informed design of dual-cure adhesives for camera modules via microscale digital image correlation

Minhyuck Lee, Jangmi Seo, Jiwon Baek, Sang-Eui Lee, Tae-Ik Lee

Materials & Design· Volume 260

Abstract

• Deformation-informed design of dual-cure adhesives for automotive camera modules. • Achieved 43.8 MPa strength and 1.77 % cure shrinkage with dual-cure adhesive. • Visualized microscale deformation at joints using digital image correlation. • Reduced diagnostic time from months to a day through early-phase inspection. As autonomous driving expands, high-performance camera modules have become essential. Dual-cure adhesives, critical for the active alignment of optical components in the modules, must ensure thermo-mechanical reliability. This study proposes a deformation-informed design of dual-curing adhesives across the entire product cycle, from chemical formulation to mechanical reliability evaluation of camera modules. Three dual-curing adhesives were formulated using diglycidyl ether of bisphenol A, with controlled epoxy–acrylate ratios, mercaptan curing agents, and OH-functionalized silica fillers. The adhesive-bonded assemblies were characterized using microscale digital image correlation, which enabled evaluation of adhesive joint deformation during early-phase, component-level reliability testing and identification of vulnerable properties and weak sites. The optimized adhesive exhibited superior performance, achieving a strength of 43.8 MPa and a cure shrinkage of 1.77 % through feedback-guided enhancement. The time to detect interfacial failure, previously requiring a month-long thermal shock test, was reduced to one hour. The developed 8-megapixel camera module passed thermo-mechanical reliability tests, maintaining a spatial frequency response change of less than 0.15 after 1,000 thermal shock cycles between −40 °C and 115 °C, as well as 164 h of high temperature-humidity testing at 85 °C and 85 % relative humidity.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Epoxy Resin Curing Processes · Photopolymerization techniques and applications · Mechanical Behavior of Composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (59)

Show source-provided references
1. Autonomous driving system: a comprehensive survey10.1016/j.eswa.2023.122836 ↗
2. A Survey on Testbench-based Vehicle-in-the-Loop simulation Testing for Autonomous Vehicles: Architecture, Principle, and Equipment10.1002/aisy.202300778 ↗
3. Perception and sensing for autonomous vehicles under adverse weather conditions: a survey10.1016/j.isprsjprs.2022.12.021 ↗
4. Robustness of visual perception system in progressive challenging weather scenarios
5. Lens design for active alignment of mobile phone cameras10.1117/1.OE.56.6.065102 ↗
6. Application of deep learning in active alignment leads to high-efficiency and accurate camera lens assembly10.1364/OE.537241 ↗
7. Why, when and how to Apply active Alignment: tackling the flexibility and cost‐effectiveness challenges in today's and future micro and nano‐optics production systems10.1002/phvs.202000045 ↗
8. Electromagnetic interference shielding of a sequential dual-curing thiol–epoxy system reinforced with GNPs with high shape memory10.1021/acsami.5c02049 ↗
9. D. Böcherer, Y. Li, C. Rein, S. Franco Corredor, P. Hou, D. Helmer, High-resolution 3D printing of dual-curing thiol–ene/epoxy system for fabrication of microfluidic devices for bioassays, Adv. Funct. Mater. 34 (2024) 2401516, https://doi.org/10.1002/adfm.202401516.10.1002/adfm.202401516 ↗
10. Recyclable dual-curing thiol–isocyanate–epoxy vitrimers with sequential relaxation profiles10.1016/j.eurpolymj.2023.112290 ↗
11. Volume change and viscoelastic properties of UV-curable adhesives for precise positioning during curing process and their formulation10.1080/00218464.2021.1950538 ↗
12. Preparation and characterization of dual curable adhesives containing epoxy and acrylate functionalities10.1016/j.reactfunctpolym.2013.01.012 ↗
13. A review of experimental and theoretical fracture characterization of bi-material bonded joints10.1016/j.compositesb.2020.108537 ↗
14. Adhesively bonded joints – a review on design, manufacturing, experiments, modeling and challenges10.1016/j.compositesb.2024.111225 ↗
15. Experimental investigation of the effects of adhesive defects on the strength and creep behavior of single-lap adhesive joints at various temperatures
16. Dual-curing epoxy thermosets: design, curing, properties and applications10.1080/15583724.2024.2405684 ↗
17. Unexpected thermomechanical behavior of off-stoichiometry epoxy/amine materials10.1021/acs.macromol.2c02414 ↗
18. Estimating the effect of age-induced defocus on object detection performance of automotive cameras10.1016/j.rineng.2025.105951 ↗
19. Analysis of package design of optic modules for automotive cameras to realize reliable image sharpness
20. Accelerated development of novel biomass-based polyurethane adhesives via machine learning10.1021/acsami.4c20371 ↗
21. Data-driven design of topologically optimized auxetic metamaterials for tailored stress–strain and Poisson’s ratio-strain behaviors10.1016/j.matdes.2025.114290 ↗
22. Evaluation and characterization of functionally graded adhesive joints: experimental and numerical analyses10.3390/polym16243561 ↗
23. Enhancing materials property prediction by leveraging computational and experimental data using deep transfer learning10.1038/s41467-019-13297-w ↗
24. Residual thermal strain distribution measurement of underfills in flip chip electronic packages by an inverse approach based on the sampling moiré method10.1007/s11340-019-00571-7 ↗
25. Determination of fracture toughness of polymer coating using micro-scale digital image correlation technique10.1016/j.polymertesting.2020.106896 ↗
26. Remaining lifetime assessment of 141,000-hour service-aged forge 91-pipe 91 steel header welds with novel in-situ digital image correlation10.1016/j.matdes.2022.111102 ↗
27. Measurement of local thermal deformations in heterogeneous microstructures via SEM imaging with digital image correlation10.1007/s11340-016-0206-6 ↗
28. Direct visualization of cross-sectional strain distribution in flexible devices10.1021/acsami.9b01480 ↗
29. Extended depth-of-field microscopic imaging with a variable focus microscope objective10.1364/OE.19.000353 ↗
30. Two-dimensional digital image correlation for in-plane displacement and strain measurement: a review10.1088/0957-0233/20/6/062001 ↗
31. Digital image correlation with enhanced accuracy and efficiency: a comparison of two subpixel registration algorithms10.1007/s11340-016-0180-z ↗
32. Evaluating free thermal expansion and glass transition of ultrathin polymer films on heated liquid10.1021/acsami.4c02279 ↗
33. Mean intensity gradient: an effective global parameter for quality assessment of the speckle patterns used in digital image correlation10.1016/j.optlaseng.2009.08.010 ↗
34. Multilayer-tuned surface plasmon modes using molecular nanolayer of (3-mercaptopropyl)trimethoxysilane applicable for nanobiosensing application10.1016/j.matdes.2018.05.068 ↗
35. Robust and seamless integration of thiol-ene-epoxy thermosets with thermoplastics and glass as hybrid microfluidic devices suitable for drug studies10.1002/admi.202300972 ↗
36. Multifunctional aluminum pre-treatments from end-functionalized phosphonic acid self-assembled monolayers10.1021/acs.langmuir.3c02629 ↗
37. Cure shrinkage characterization of an epoxy resin system by two in situ measurement methods10.1002/pc.20949 ↗
38. Volumetric effective cure shrinkage measurement of dual curable adhesives by fiber Bragg grating sensor10.1007/s10853-020-04716-1 ↗
39. Noncovalent interactions in mechanical response of thermoset epoxy resin10.1021/acs.jpcb.3c07369 ↗
40. Quantitative evaluation of crack arrest mechanisms in epoxy/silica nanocomposites10.1016/j.compscitech.2024.111028 ↗
41. Modeling of the stress-strain behavior of an epoxy-based nanocomposite filled with silica nanoparticles10.1016/j.matdes.2015.10.038 ↗
42. Effect of cross-linking on dynamic mechanical and fracture behavior of epoxy variants10.1016/j.compositesb.2015.09.017 ↗
43. Cure kinetics, morphology and miscibility of modified DGEBA-based epoxy resin - Effects of a liquid rubber inclusion10.1016/j.polymer.2007.01.018 ↗
44. Residual stress and thermal properties of rubber-modified epoxy systems for semiconductor package10.1002/app.51786 ↗
45. Next-generation structural adhesives composed of epoxy resins and hydrogen-bonded styrenic block polymer-based thermoplastic elastomers10.1021/acsami.4c12540 ↗
46. Co-enhancement of toughness and strength of room-temperature curing epoxy adhesive derived from hydroxyl-terminated polybutadiene based polyurethane resin10.1016/j.eurpolymj.2024.113373 ↗
47. Failure mechanisms of the bonded interface between mold epoxy and metal substrate exposed to high temperature10.1016/j.compositesb.2023.110562 ↗
48. Unveiling the chemical reactions involved in moisture-induced weakening of adhesion between aluminum and epoxy resin10.1021/acs.jpcc.8b03549 ↗
49. Interface strength and degradation of adhesively bonded porous aluminum oxides, npj Mater
50. Chemical, mechanical and morphological investigation on the hygrothermal aging mechanism of a toughened epoxy10.1016/j.polymertesting.2022.107548 ↗
51. Reactive molecular dynamics study of hygrothermal degradation of crosslinked epoxy polymers10.1021/acsapm.2c00383 ↗
52. Understanding water diffusion behaviors in epoxy resin through molecular simulations and experiments10.1021/acs.langmuir.3c03766 ↗
53. Water in epoxy coatings: basic principles of interaction with polymer matrix and the influence on coating life cycle
54. C. Li, A. Strachan, Free volume evolution in the process of epoxy curing and its effect on mechanical properties, 97 (2016) 456-464, http://dx.doi.org/10.1016/j.polymer.2016.05.059.10.1016/j.polymer.2016.05.059 ↗
55. Effects of moisture ingress on the mesoscale mechanical properties of epoxy adhesives under elevated temperature10.1016/j.polymertesting.2020.107049 ↗
56. Model of moisture absorption by adhesive joint10.1016/j.ymssp.2017.06.042 ↗
57. Changes in the structure and physical properties of acrylic and epoxy adhesives in response to high-temperature and high-humidity environments
58. Water and corrosion resistance of epoxy-acrylic-amine waterborne coatings: effects of resin molecular weight, polar group and hydrophobic segment10.1016/j.corsci.2013.05.020 ↗
59. Modified epoxy acrylate resin for photocurable temporary protective coatings10.1016/j.porgcoat.2015.07.022 ↗