journal article·2019-11Open access

Additive manufacturing of biodegradable Zn-xWE43 porous scaffolds: Formation quality, microstructure and mechanical properties

Yu Qin, Peng Wen, Maximilian Voshage, Yanzhe Chen, Paul Georg Schückler, Lucas Jauer, Dandan Xia, Hui Guo, Yufeng Zheng, Johannes Henrich Schleifenbaum

Materials & Design· Volume 181

Abstract

Zn is promising candidate material for biodegradable implants due to its acceptable biocompatibility and moderate degradation rate. However, the strength of pure Zn metal is regarded not enough. In this work, Zn-xWE43 porous scaffolds were fabricated by laser powder bed fusion (L-PBF) with different mass ratios of WE43: 2%, 5% and 8%. WE43 is a biodegradable Mg alloy with addition of Y and rare earth elements, and has been clinically verified. The formation quality, microstructure and mechanical properties were analyzed. L-PBF samples with high densification were achieved. Rapid cooling rate and the addition of WE43 together resulted to grain refinement. With increasing content of WE43, more Zn + Mg2Zn11 eutectics were precipitated, which increased tensile strength but decreased elongation. The formation of brittle MgZn2 deteriorated strength in Zn-8WE43. Zn-5WE43 showed the highest tensile strength of 335.4 MPa, but the elongation was only 1%. The compressive strength and Young's modulus of Zn-5WE43 porous scaffolds was 73.2 MPa and 2480 MPa, while 22.9 MPa and 950 MPa for pure Zn porous scaffolds respectively. The present results addressed the key technical issues and pointed out the future directions on additive manufacturing of Zn alloy porous scaffolds for biodegradable application.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Bone Tissue Engineering Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. Biofabrication of bone tissue: approaches, challenges and translation for bone regeneration10.1016/j.biomaterials.2016.01.024 ↗
2. Bone tissue regeneration: the role of scaffold geometry10.1039/C4BM00291A ↗
3. Recent advances in manufacturing and surface modification of titanium orthopaedic applications10.1016/j.proeng.2017.01.259 ↗
4. Microstructure, phase composition and mechanical properties of new, low cost Ti-Mn-Nb alloys for biomedical applications10.1016/j.jallcom.2019.02.116 ↗
5. Evaluation of mechanical and wear properties of Ti xNb 7Fe alloys designed for biomedical applications10.1016/j.matdes.2016.09.029 ↗
6. Additive manufacturing of cardiovascular CoCr stents by selective laser melting10.1016/j.matdes.2017.01.091 ↗
7. Anisotropy in the microstructure and mechanical property for the bulk and porous 316L stainless steel fabricated via selective laser melting10.1016/j.matlet.2018.09.152 ↗
8. Biodegradable metals10.1016/j.mser.2014.01.001 ↗
9. Y. Liu, Y. Zheng, X.-H. Chen, J.-A. Yang, H. Pan, D. Chen, L. Wang, J. Zhang, D. Zhu, S. Wu, K.W.K. Yeung, R.-C. Zeng, Y. Han, S. Guan, Fundamental theory of biodegradable metals - definition, criteria, and design, Adv. Funct. Mater. 0(0) 1805402.
10. Biodegradable magnesium alloys for orthopaedic applications: a review on corrosion, biocompatibility and surface modifications10.1016/j.msec.2016.06.020 ↗
11. H. Gong, K. Wang, R. Strich, J.G. Zhou, In vitro biodegradation behavior, mechanical properties, and cytotoxicity of biodegradable Zn–Mg alloy, J Biomed Mater Res B Appl Biomater (2015) n/a–n/a. doi:https://doi.org/10.1002/jbm.b.33341.10.1002/jbm.b.33341 ↗
12. Effects of mg on microstructure and corrosion properties of Zn–mg alloy10.1016/j.jallcom.2014.03.025 ↗
13. Design and characterizations of novel biodegradable Zn-Cu-Mg alloys for potential biodegradable implants10.1016/j.matdes.2016.12.075 ↗
14. Zinc-based alloys for degradable vascular stent applications10.1016/j.actbio.2018.03.005 ↗
15. The influence of alloying and fabrication techniques on the mechanical properties, biodegradability and biocompatibility of zinc: a comprehensive review10.1016/j.actbio.2019.01.035 ↗
16. Zinc exhibits ideal physiological corrosion behavior for bioabsorbable stents10.1002/adma.201300226 ↗
17. Zn-Li alloy after extrusion and drawing: structural, mechanical characterization, and biodegradation in abdominal aorta of rat10.1016/j.msec.2017.02.167 ↗
18. Processability of pure Zn and pure Fe by SLM for biodegradable metallic implant manufacturing10.1108/RPJ-08-2015-0100 ↗
19. Densification behavior of pure Zn metal parts produced by selective laser melting for manufacturing biodegradable implants10.1016/j.jmatprotec.2018.03.007 ↗
20. Laser additive manufacturing of Zn metal parts for biodegradable applications: processing, formation quality and mechanical properties10.1016/j.matdes.2018.05.057 ↗
21. A combined strategy to enhance the properties of Zn by laser rapid solidification and laser alloying10.1016/j.jmbbm.2018.03.018 ↗
22. Selective laser melting of Zn–Ag alloys for bone repair: microstructure, mechanical properties and degradation behaviour10.1080/17452759.2018.1458991 ↗
23. Laser additive manufacturing of Zn porous scaffolds: shielding gas flow, surface quality and densification10.1016/j.jmst.2018.09.065 ↗
24. Additive manufacturing of biodegradable metals: current research status and future perspectives10.1016/j.actbio.2019.04.046 ↗
25. Safety and performance of the drug-eluting absorbable metal scaffold (DREAMS) in patients with de-novo coronary lesions: 12 month results of the prospective, multicentre, first-in-man BIOSOLVE-I trial10.1016/S0140-6736(12)61765-6 ↗
26. Additive manufactured WE43 magnesium: a comparative study of the microstructure and mechanical properties with those of powder extruded and as-cast WE4310.1016/j.matchar.2018.11.011 ↗
27. Manufacture by selective laser melting and mechanical behavior of commercially pure titanium10.1016/j.msea.2013.11.038 ↗
28. Additively manufactured biodegradable porous magnesium10.1016/j.actbio.2017.12.008 ↗
29. Comparison of density measurement techniques for additive manufactured metallic parts10.1108/13552541111156504 ↗
30. Corrosion mechanism of model zinc–magnesium alloys in atmospheric conditions10.1016/j.corsci.2008.06.008 ↗
31. Influence of element vaporization on formability, composition, microstructure, and mechanical performance of the selective laser melted Mg–Zn–Zr components10.1016/j.matlet.2015.05.074 ↗
32. 10 - design for laser additive manufacturing
33. Mechanical and corrosion properties of newly developed biodegradable Zn-based alloys for bone fixation10.1016/j.actbio.2011.05.008 ↗
34. Novel Zn-based alloys for biodegradable stent applications: design, development and in vitro degradation10.1016/j.jmbbm.2016.03.018 ↗
35. Effect of secondary phase particles on thermal stability of ultra-fine grained Mg-4Y-3RE alloy prepared by equal channel angular pressing10.1016/j.matchar.2018.04.006 ↗
36. Additive manufacturing of metallic components – process, structure and properties10.1016/j.pmatsci.2017.10.001 ↗
37. Topological design and additive manufacturing of porous metals for bone scaffolds and orthopaedic implants: a review10.1016/j.biomaterials.2016.01.012 ↗
38. Additively manufactured metallic porous biomaterials based on minimal surfaces: a unique combination of topological, mechanical, and mass transport properties10.1016/j.actbio.2017.02.024 ↗