journal article·2016-10

Slag recycling in submerged arc welding and its effects on the quality of stainless steel claddings

Jatinder Garg, Kulwant Singh

Materials & Design· Volume 108
Publisher page

Abstract

Abstract A novel technology for recycling of slag waste generated during submerged arc cladding of stainless steel (SS) was developed. The claddings produced using “recycled slag” were analysed for their quality and performance during service. The chemical composition of these claddings was found to be within the acceptable range of American Society of Mechanical Engineers (ASME) specifications. Their resistance to various types of corrosion, as determined by conducting different standard emersion and electrochemical tests, was found to be at par with the claddings produced with fresh flux. Results of bend test indicate that these claddings possess good mechanical properties and bond integrity with the substrate at all points. The microstructure examination revealed that both types of claddings (deposited with fresh flux and recycled slag) solidified in same mode of solidification and have similar grain size, shape and phase distribution, in all zones. The microhardness values of the deposited metal, heat affected zone and base metal for both types of cladding are comparable. Ferrite measurements done theoretically as well as practically showed the presence of adequate amount of ferrite to prevent hot fissuring. The cost of recycled slag was calculated and found to be 73% less than the equivalent fresh flux.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Metal Alloys Wear and Properties · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (39)

Show source-provided references
1. The use of submerged-arc welding flux slag as raw material for the fabrication of multiple-use mortars and bricks10.1590/S0104-92242009000300009 ↗
2. Utilisation of welding slag waste in ceramic materials for civil construction10.1080/09507110701637908 ↗
3. Reuse of slag as flux in submerged arc welding and its effect on chemical composition, bead geometry and microstructure of the weld metal
4. Reuse of slag in stainless steel cladding and its effect on chemistry of claddings
5. Solving multi-criteria optimization problem in submerged arc welding consuming a mixture of fresh flux and fused slag10.1007/s00170-006-0776-z ↗
6. Modeling and optimization of features of bead geometry including percentage dilution in submerged arc welding using mixture of fresh flux and fused slag10.1007/s00170-006-0917-4 ↗
7. Recycling saw slag proves reliable and repeatable
8. Recycling of slag to act as a flux in submerged arc welding10.1016/j.resconrec.2009.04.006 ↗
9. Machinability investigations on turning of Cr-Ni-based stainless steel cladding formed by laser cladding process
10. Weld overlay cladding of high strength low alloy steel with austenitic stainless steel - structure and properties10.1016/j.matdes.2010.10.026 ↗
11. A comparative study on microstructure and properties of Inconel 52M overlays deposited by laser beam and GTA cladding10.1007/s00170-015-7198-8 ↗
12. Stainless steel cladding deposited by automatic gas metal arc welding
13. Lai · 2013
14. Studies on metallurgical and impact toughness behavior of variably sensitized weld metal and heat affected zone of AISI 304L welds10.1016/j.matdes.2015.09.145 ↗
15. Prediction of delta ferrite content and effect of welding process parameters in claddings by FCAW10.1080/10426910500471409 ↗
16. Arc stability and its impact on weld properties and microstructure in anti-phase synchronised synergic-pulsed twin-wire gas metal arc welding10.1016/j.matdes.2014.11.052 ↗
17. Development of agglomerated acidic flux for submerged arc welding10.3176/eng.2010.2.02 ↗
18. Eager · 1979
19. Investigation on flux design for submerged arc welding of high- strength low-alloy steel10.1177/0954405412468993 ↗
20. A review study of submerged arc welding fluxes
21. Corrosion behavior of welded stainless steel
22. Physical-mechanical and electrochemical corrosion behaviors of additively manufactured Cr-Ni-based stainless steel formed by laser cladding10.1016/j.matdes.2016.03.151 ↗
23. Microstructural characterization of an sa508–309l/308l–316l domestic dissimilar metal welded safe-end joint10.1016/j.matchar.2014.08.023 ↗
24. Effect of welding conditions on microstructure and properties of type 316L stainless steel submerged arc cladding
25. Lippold · 2005
26. Effect of manganese and nitrogen on the solidification mode in austenitic stainless steel welds10.1007/BF02648382 ↗
27. Crevice corrosion of stainless steels in sea water: correlation of field data with laboratory ferric chloride tests10.5006/1.3622163 ↗
28. Corrosion resistance of stainless steel weldments
29. Corrosion of weldments
30. Suitable corrosion test methods for stainless steel welds10.1007/BF03266626 ↗
31. Corrosion testing of welds, a review of methods10.1007/BF03266589 ↗
32. Jessen · 2011
33. Austenitic solidification mode in austenitic stainless steel welds10.1007/BF02811663 ↗
34. Microstructure and mechanical properties of AISI 347 stainless steel/A335 low alloy steel dissimilar joint produced by gas tungsten arc welding10.1016/j.matdes.2013.03.029 ↗
35. Effect of heat input on the microstructure and mechanical properties of gas tungsten arc welded AISI 304 stainless steel joints10.1016/j.matdes.2011.02.017 ↗
36. Nadkarni · 2005
37. Study on slag detachability and stick slag mechanism of SSFCE
38. Effect of ferro-titanium deoxidant on metal recovery and slag detachability of an austenitic stainless steel electrode10.1007/s12666-008-0049-7 ↗
39. Arc stability study of submerged arc welding for SiO2 and TiO2 based flux systems