A strong, wear- and corrosion-resistant, and antibacterial Co–30 at.% Cr–5 at.% Ag ternary alloy for medical implants
Source abstract
Abstract
A Co–30 at.% Cr–5 at.% Ag alloy was fabricated using a combination of mechanical alloying and spark plasma sintering. The microstructure of the alloy consisted of an ultrafine-grained ε-Co solid solution matrix with an average grain size of 167 nm and uniformly dispersed Ag particles with an average size of 72 nm and a minor amount of nanoscale σ-precipitates with size of 23 nm. Such particular microstructure enabled high hardness of 650 HV and compressive strength of up to 2.3 GPa. Pin-on-disk dry sliding wear tests show that the present alloy exhibited superior wear resistance, with wear rate in the order of 10−5 mm3/(N·m) upon sliding against alumina. The wear-induced microstructure extended only ~500 nm from the sliding surface, with elongated Ag particles. The alloy also demonstrated high resistance to corrosion in artificial saliva solution, due to the formation of a protective passive film. Moreover, the addition of Ag also significantly enhanced the antibacterial activity of Co–Cr alloys, with antibacterial rates against E. coli and S. aureus of 90.5% and 72.6%, respectively. The present alloy with a combination of high strength, superior wear- and corrosion-resistance, and excellent antibacterial activity offers a promising candidate for medical implants.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Orthopaedic implants and arthroplasty · Advanced materials and composites · Titanium Alloys Microstructure and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (58)
Show source-provided references
1. Metallic implant biomaterials10.1016/j.mser.2014.10.001 ↗
2. Titanium alloys in total joint replacement—a materials science perspective10.1016/S0142-9612(97)00146-4 ↗
3. Evaluation of mechanical and wear properties of TixNb7Fe alloys designed for biomedical applications10.1016/j.matdes.2016.09.029 ↗
4. Evaluation of the mechanical and wear properties of titanium produced by three different additive manufacturing methods for biomedical application10.1016/j.msea.2019.06.024 ↗
5. Microstructure, phase composition and mechanical properties of new, low cost Ti-Mn-Nb alloys for biomedical applications10.1016/j.jallcom.2019.02.116 ↗
6. The properties of a wrought biomedical cobalt-chromium alloy10.1007/BF00975070 ↗
7. Changes in the surface oxide composition of Co–Cr–Mo implant alloy by macrophage cells and their released reactive chemical species10.1016/j.biomaterials.2003.08.016 ↗
8. Electrochemical synthesis of a biomedically important Co–Cr alloy10.1016/j.actamat.2010.01.053 ↗
9. An assessment of ultra fine grained 316L stainless steel for implant applications10.1016/j.actbio.2015.10.043 ↗
10. Physico-mechanical properties and prosthodontic applications of Co-Cr dental alloys: a review of the literature10.4047/jap.2014.6.2.138 ↗
11. Mechanical properties of Co-Cr alloys for metal base framework
12. The composition of the surface passive film formed on CoCrMo alloy in simulated physiological solution10.1016/S0013-4686(03)00396-7 ↗
13. Characterization of the surface oxide film of a Co–Cr–Mo alloy after being located in quasi-biological environments using XPS10.1016/S0169-4332(01)00551-7 ↗
14. Interactive effects of albumin and phosphate ions on the corrosion of CoCrMo implant alloy10.1149/1.2764238 ↗
15. Origin of the selective Cr oxidation in CoCr alloy surfaces10.1021/jz1007164 ↗
16. Microstructure, hardness, corrosion resistance and porcelain shear bond strength comparison between cast and hot pressed CoCrMo alloy for metal–ceramic dental restorations10.1016/j.jmbbm.2012.03.015 ↗
17. Cooling rate and carbon content effect on the fraction of secondary phases precipitate in as-cast microstructure of ASTM F75 alloy10.1016/j.jmatprotec.2008.04.039 ↗
18. The acting wear mechanisms on metal-on-metal hip joint bearings: in vitro results10.1016/S0043-1648(01)00654-8 ↗
19. Pin-on-disk wear behavior in a like-on-like configuration in a biological environment of high carbon cast and low carbon forged Co–29Cr–6Mo alloys10.1016/j.actamat.2006.10.005 ↗
20. Effects of sigma phase and carbide on the wear behavior of CoCrMo alloys in Hanks' solution10.1016/j.wear.2013.12.010 ↗
21. New insights into hard phases of CoCrMo metal-on-metal hip replacements10.1016/j.jmbbm.2012.03.013 ↗
22. Effects of boronizing on mechanical and dry-sliding wear properties of CoCrMo alloy10.1016/j.matdes.2010.03.024 ↗
23. Microstructure and tribological characteristics of aged Co–28Cr–5Mo–0.3C alloy10.1016/j.matdes.2011.12.041 ↗
24. Dry sliding and tribocorrosion behaviour of hot pressed CoCrMo biomedical alloy as compared with the cast CoCrMo and Ti6Al4V alloys
25. Development of new Co–Cr–W-based biomedical alloys: effects of microalloying and thermomechanical processing on microstructures and mechanical properties10.1016/j.matdes.2013.10.052 ↗
26. Effects of nitrogen on microstructural evolution of biomedical Co–Cr–W alloys during hot deformation and subsequent cooling10.1016/j.matdes.2013.12.080 ↗
27. Microstructure and dry sliding wear behavior of ultrafine-grained Co-30 at% Cr alloy at room and elevated temperatures10.1016/j.jallcom.2018.08.092 ↗
28. Fabrication, tribological and corrosion behaviors of ultra-fine grained Co–28Cr–6Mo alloy for biomedical applications10.1016/j.jmbbm.2015.12.039 ↗
29. Fabrication and evaluation of bulk nanostructured cobalt intended for dental and orthopedic implants10.1016/j.jmbbm.2017.01.039 ↗
30. Infection of orthopedic implants with emphasis on bacterial adhesion process and techniques used in studying bacterial-material interactions10.4161/biom.22905 ↗
31. A mechanistic study of the antibacterial effect of silver ions on Escherichia coli and Staphylococcus aureus10.1002/1097-4636(20001215)52:4<662::AID-JBM10>3.0.CO;2-3 ↗
32. The bactericidal effect of silver nanoparticles10.1088/0957-4484/16/10/059 ↗
33. Effect of nano/micro-Ag compound particles on the bio-corrosion, antibacterial properties and cell biocompatibility of Ti-Ag alloys10.1016/j.msec.2017.02.142 ↗
34. Effect of silver on microstructure and antibacterial property of 2205 duplex stainless steel10.1016/j.msec.2016.03.014 ↗
35. The Ag−Co (silver-cobalt) system10.1007/BF02869002 ↗
36. The Ag-Cr (silver-chromium) system10.1007/BF03029296 ↗
37. High-temperature wear behavior of self-lubricating Co matrix alloys prepared by P/M10.1016/j.wear.2015.11.009 ↗
38. Sliding wear-induced chemical nanolayering in Cu-Ag, and its implications for high wear resistance10.1016/j.actamat.2014.03.060 ↗
39. Sliding wear induced subsurface microstructural evolution in nanocrystalline Nb-Ag binary alloys and its impact on tribological performance10.1016/j.wear.2017.09.013 ↗
40. Sliding wear of nanocrystalline Nb-Ag at elevated temperatures: evolution of subsurface microstructure and its correlation with wear performance10.1016/j.wear.2018.08.018 ↗
41. Microstructure, sliding wear and corrosion behavior of bulk nanostructured Co-Ag immiscible alloys10.1016/j.jallcom.2018.03.213 ↗
42. Direct evidence of magnetically induced phase separation in the fcc phase and thermodynamic calculations of phase equilibria of the Co–Cr system10.1016/S1359-6454(01)00433-5 ↗
43. Contact and rubbing of flat surfaces10.1063/1.1721448 ↗
44. Bio-corrosion and cytotoxicity studies on novel Zr55Co30Ti15 and Cu60Zr20Ti20 metallic glasses10.1007/s11661-014-2574-9 ↗
45. The crystal structure of the Co-Cr σ phase10.1107/S0365110X56000826 ↗
46. Overview no. 3 fracture-mechanism maps and their construction for f.c.c. metals and alloys10.1016/0001-6160(79)90105-6 ↗
47. Failure of metals I: brittle and ductile fracture10.1016/j.actamat.2015.12.034 ↗
48. Tribological properties of molybdenized silver-containing nickel base alloy at elevated temperatures10.1016/j.triboint.2008.12.004 ↗
49. Elevated temperature tribological behavior of Ni based composites containing nano-silver and hBN10.1016/j.wear.2010.08.022 ↗
50. CrN-Ag nanocomposite coatings: tribology at room temperature and during a temperature ramp10.1016/j.surfcoat.2009.09.018 ↗
51. CrN–Ag nanocomposite coatings: high-temperature tribological response10.1016/j.wear.2010.03.015 ↗
52. Antibacterial activity, corrosion resistance and wear behavior of spark plasma sintered Ta-5Cu alloy for biomedical applications10.1016/j.jmbbm.2017.06.022 ↗
53. Microstructure and strength of nickel at large strains10.1016/S1359-6454(00)00082-3 ↗
54. Formation of nano-laminated structure in nickel by means of surface mechanical grinding treatment10.1016/j.actamat.2015.06.014 ↗
55. Geometrically necessary, incidental and subgrain boundaries10.1016/0956-716X(91)90451-6 ↗
56. Geometrically necessary boundaries, incidental dislocation boundaries and geometrically necessary dislocations10.1016/S1359-6462(02)00358-5 ↗
57. Cobalt toxicity after McKee hip arthroplasty10.1302/0301-620X.57B3.289 ↗
58. Silver as antibacterial agent: ion, nanoparticle, and metal10.1002/anie.201205923 ↗