journal article·2025-12Open access

Research on the microstructural differences and mechanical response mechanisms of martensitic stainless steel additive manufacturing under cross-scale heat input control

Liangliang Zhang, Yu Miao, Jianyong Wang, Meng Zhang, Yingying Liu, Yang Zhou, Pengjun Zuo, Zhuoran Shi, Shifeng Liu, Sefei Yang

Materials & Design· Volume 260

Abstract

• DED offers 45 % tensile strain & 45 J impact toughness, doubling the performance of SLM. • Low DED cooling forms coarse martensite, minor austenite, sparse Cr 7 C 3 & low δ-phase networks for high toughness. • High cooling rate SLM forms fine martensite, δ-phase networks, and dense Cr 3 C 2 , inducing high strength but crack susceptibility via dislocation pinning. Additively manufactured precipitation-hardened martensitic stainless steels (PHMSS-AMs) exhibit significant brittleness, with microstructure primarily governed by cooling rate, which correlates positively with heat input. Different additive manufacturing (AM) methods involve heat inputs varying by orders of magnitude, leading to substantial differences in PHMSS-AM microstructure and mechanical properties. This study systematically compares microstructure and mechanical behavior of 17-4PH steel fabricated by laser-directed energy deposition (DED) and selective laser melting (SLM), which use the same heat source type but differ in heat input by approximately three orders of magnitude. The results revealed that high heat input (DED) significantly improves ductility and toughness, while low heat input (SLM) favors higher strength. DED samples achieved an average maximum tensile strain of 45 %—double that of SLM samples and aged wrought material—and higher impact toughness (45 J vs. 25 J for SLM). The slower DED cooling rate produced wider martensitic laths, reduced δ-phase networking, and lower Cr 7 C 3 carbide density, decreasing dislocation pinning and facilitating slip, thus enhancing ductility and toughness. Conversely, rapid SLM cooling promoted finer martensitic laths, pronounced δ-phase networks, and higher Cr 7 C 3 carbide density, causing strong dislocation pinning and resulting in high strength but low ductility and toughness.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Laser Material Processing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (58)

Show source-provided references
1. Weldability of 17–4 PH stainless steel in centrifugal compressor impeller applications10.1016/j.jmatprotec.2004.07.117 ↗
2. Laser powder bed fusion of precipitation-hardened martensitic stainless steels: a review10.3390/met10020255 ↗
3. Additive manufacturing of ultra-high strength steels: a review
4. C.R. Das, H.C. Dey, Srinivasan G, et al. Weldability of 17-4PH stainless steel in overaged heat treated condition. Sci Technol Weld Join 2006, 11(5):502-508, doi: 10.1179/174329306X148147.10.1179/174329306X148147 ↗
5. Additive manufacturing of nickel superalloys: opportunities for innovation and challenges related to qualification10.1007/s11661-018-4702-4 ↗
6. Phase transformation dynamics guided alloy development for additive manufacturing
7. Enhanced strength and ductility of laser-directed energy deposition repaired IN718 superalloy via a novel tailored heat treatment
8. Solidification in metal additive manufacturing: challenges, solutions, and opportunities10.1016/j.pmatsci.2024.101361 ↗
9. Investigation of the thermal behavior during the direct writing metal additive manufacturing
10. Grain size evolution under different cooling rate in laser addi-tive manufacturing of superalloy10.1016/j.optlastec.2019.105662 ↗
11. Additive manufacturing of Fe–Mn–Al–C lightweight steel by laser powder bed fusion: the role of laser scanning speed on forming quality, microstructure and properties
12. Effect of laser spot size, scanning strategy, scanning speed, and laser power on microstructure and mechanical behavior of 316l stainless steel fabricated via selective laser melting10.1007/s11665-021-06387-8 ↗
13. Effect of focal spot size on AlSi10Mg alloy parts fabricated by laser powder bed fusion: process window, mechanical properties, and microstructure
14. Laser spot size and scaling laws for laser beam additive manufacturing
15. Selective laser melting additive manufactured Inconel 718 superalloy parts: high-temperature oxidation property and its mechanisms
16. Research progress on additive manufacturing of 17–4PH martensitic stainless steels
17. A comparative investigation of the electrochemical behavior of as-printed 17–4 PH stainless steel produced by L-PBF and L-DED10.1016/j.corsci.2025.112780 ↗
18. Structural evolutions in 3D-printed Fe-based metallic glass fabricated by selective laser melting
19. In situ laser synthesis of fe-based amorphous matrix composite coating on structural steel10.1007/s11661-012-1312-4 ↗
20. Material-structure-performance integrated laser-metal additive manufacturing10.1126/science.abg1487 ↗
21. Investigation on Ti-6Al-4V microstructure evolution in selective laser melting10.3390/met9121270 ↗
22. Effect of adaptive control of cooling rate on microstructure and mechanical properties of laser additively manufactured Inconel 718 thin walls10.1016/j.matchar.2024.114032 ↗
23. Effects of cooling rate on the microstructure and tensile properties of wire-arc additive manufactured Ti–6Al–4V alloy10.1007/s12540-019-00563-1 ↗
24. Effect of compositional variations on the heat treatment response in 17–4 PH stainless steel fabricated by laser powder bed fusion10.1016/j.matchar.2024.113768 ↗
25. Detailed analysis of nucleation and subsequent δ to γ phase transformation of a high N super austenitic stainless steel
26. Influences of cooling rates on solidification and segregation cha-racteristics of Fe-Cr-Ni-Mo-N super austenitic stainless steel10.1016/j.jmatprotec.2019.116326 ↗
27. Modelling of delta ferrite to austenite phase transformation kinetics in martensitic steels: application to rapid cooling in additive manufacturing10.1016/j.mtla.2021.101157 ↗
28. Kinetics of peritectic reaction and transformation in Fe-C alloys10.1007/s11663-000-0074-3 ↗
29. Effect of powder chemical composition on the as-built microstructure of 17–4 PH stainless steel processed by selective laser melting
30. Microstructures and mechanical prop-erties of multi-layered materials composed of Ti-6Al-4V, vanadium, and 17–4PH stainless steel produced by directed energy deposition
31. Simultaneous enhancement of strength-ductility via multiple precipitates and austenite in a novel precipitation-hardened martensitic stainless steel10.1016/j.msea.2023.145062 ↗
32. Thermally driven changes in the microstructure and mechanical properties of martensitic 15–5 precipitation-hardened stainless steel during directed energy deposition
33. Steels in additive manufacturing: a review of their microstructure and properties10.1016/j.msea.2019.138633 ↗
34. Effect of δ ferrite on impact property of hot-rolled 12Cr–Ni steel
35. Effects of additive manufacturing processes and isothermal aging on the microstructure and properties of 13–8 Mo precipitation hardening martensitic stainless steel
36. Selective laser melting and heat treatment of precipitation hardening stainless steel with a refined microstructure and excellent mechanical properties
37. Microstructure and property of a selective laser melting process induced oxide dispersion strengthened 17–4 PH stainless steel
38. Review of: Welding metallurgy and weldability of stainless steel10.1080/10426910500476747 ↗
39. Microstructure and properties of SLM formed 17–4PH high strength steel
40. Effect of heat treatment on microstructure, mechanical and corrosion properties of austenitic stainless steel 316L using arc additive manufacturing
41. Formation of delta-ferrite and its effect on impact to-ughness of GTAW weld metals in a 12 wt-% Cr steel10.1080/13621718.2022.2148063 ↗
42. Influence of small amount and different morphology of secondary phases on impact toughness of UNS S32205 Duplex Stainless Steel
43. Effect of delta ferrites on the anisotropy of impact toughn-ess in martensitic heat-resistant steel10.1016/j.jmrt.2018.12.008 ↗
44. Effect of heat input on the microstructure and mechanical properties of the deposition obtained by selective laser melting (SLM) of precipitationhardened martensitic stainless steel
45. Recommended Auger parameters for 42 elemental solids10.1016/j.elspec.2011.12.001 ↗
46. Use of tetraneopentylchromium as a precursor for the organometallic chemical vapor deposition of chromium carbide: a reinvestigation10.1021/cm00040a019 ↗
47. XPS study of the segregation of sulphur on Ni-21Cr-8Fe (100) alloy10.1016/0039-6028(91)90842-G ↗
48. Ladle-treated high manganese steel reinforced by Cr7C3 phase10.1080/13640461.2016.1242197 ↗
49. First principles investigation of binary chromium carbides Cr7C3, Cr3C2 and Cr23C6: electronic structures, mechanical properties and thermodynamic properties under pressure10.3390/ma15020558 ↗
50. Influence of microstructural parameters on the mechanical properties of oxide dispersion strengthened Fe-14Cr steels
51. Additive manufacturing of 17–4PH stainless steel: effect of heat treatment on microstructure evolution and strengthening behavior10.1016/j.msea.2024.146770 ↗
52. Rivera-Díaz-del-Castillo PEJ, Hayashi K, Galindo-Nava EI. Computational design of nanostructured steels employing irreversible thermodynamics. Mater. Sci. Technol., 2013, 29(10):1206-1211, 10.1179/1743284712Y.0000000179.10.1179/1743284712Y.0000000179 ↗
53. A model for the microstructure behaviour and strength evolution in lath martensite
54. Tuning process parameters to optimize microstructure and mechanical properties of novel maraging steel fabricated by selective laser melting
55. Effect of aging temperature on microstructure evolution and strengthening behavior of L-PBF 18Ni(300) maraging steel
56. Dissolution of δ-ferrite and its effect on mech-anical properties of P92 steel welds10.1016/j.msea.2020.139370 ↗
57. New insights into the anisotropic ductility of additively manufactured Inconel 71810.1016/j.ijplas.2023.103738 ↗
58. Ultra-high strength and ductility of eutectic high-entropy alloy with duplex heterostructure at room and cryogenic temperatures