journal article·2015-12

Microstructure and residual stress distributions in friction stir welding of dissimilar aluminium alloys

Hamed Jamshidi Aval

Materials & Design· Volume 87
Publisher page

Abstract

Abstract The aim of this investigation was to study the effect of welding heat input and postweld natural aging on residual stress, microstructure, and precipitation distribution in different zones of dissimilar friction stir welding of 8 mm thick plates of AA6082-T6 and AA7075-T6. It was found that atomic diffusion occurs at the interface of the materials in the stir zone of the joints. Transmission electron microscopic investigations showed that reprecipitation of fine Guinier–Preston zone, β′, and η′ precipitates resulted in increased micro-hardness in the SZ after natural aging. An increase in welding heat input resulted in decreased maximum tensile residual stress and increased size of the tensile residual stress region. Natural aging within the SZ and thermo-mechanical affected zone resulted in 15–20 MPa reduction of the residual stress in these zones.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. Thomas · 1991
2. Effect of welding parameters on mechanical and microstructural properties of dissimilar AA6082–AA2024 joints produced by friction stir welding10.1016/j.matdes.2008.05.044 ↗
3. Effect of tool rotational speed and pin profile on microstructure and tensile strength of dissimilar friction stir welded AA5083-H111 and AA6351-T6 aluminum alloys10.1016/j.matdes.2012.03.027 ↗
4. Defect features and mechanical properties of friction stir lap welded dissimilar AA2024–AA7075 aluminum alloy sheets10.1016/j.matdes.2013.09.062 ↗
5. Effect of tool position on the fatigue properties of dissimilar 2024–7075 sheets joined by friction stir welding10.1016/j.jmatprotec.2007.12.036 ↗
6. Dissimilar friction stir welds in AA5083–AA6082: the effect of process parameters on residual stress10.1016/j.msea.2006.08.012 ↗
7. Torque, temperature and hardening precipitation evolution in dissimilar friction stir welds between 6061-T6 and 2014-T6 aluminum alloys10.1016/j.jmatprotec.2013.01.001 ↗
8. Material flow and microstructure in the friction stir butt welds of the same and dissimilar aluminum alloys10.1007/s11665-002-0008-0 ↗
9. Residual stress measurements in a thick, dissimilar aluminum alloy friction stir weld10.1016/j.actamat.2006.04.034 ↗
10. Material flow and mechanical behaviour of dissimilar AA2024-T3 and AA7075-T6 aluminium alloys friction stir welds10.1016/j.matdes.2010.11.059 ↗
11. Mechanical and microstructural behaviour of 2024–7075 aluminium alloy sheets joined by friction stir welding10.1016/j.ijmachtools.2005.07.010 ↗
12. Weld temperature effects during friction stir welding of dissimilar aluminum alloys 6061-T6 and 7075-T610.1007/s00170-013-5485-9 ↗
13. Friction stir welding of dissimilar materials between AA6061 and AA7075 Al alloys effects of process parameters10.1016/j.matdes.2013.10.082 ↗
14. Stress corrosion cracking susceptibility of friction stir welded AA7075–AA6056 dissimilar joint10.1016/j.msea.2004.09.065 ↗
15. Effects of initial temper condition and postweld heat treatment on the properties of dissimilar friction-stir-welded joints between AA7075 and AA6061 aluminum alloys10.1007/s11661-014-2248-7 ↗
16. Constitutional liquation during dissimilar friction stir welding of Al and Mg alloys10.1016/j.scriptamat.2004.02.002 ↗
17. Effect of tool rotation rate on microstructure and mechanical properties of friction stir welded copper10.1179/136217109X456951 ↗
18. CDRX modelling in friction stir welding of aluminium alloys10.1016/j.ijmachtools.2004.12.001 ↗
19. CDRX modelling in friction stir welding of AA7075-T6 aluminum alloy: analytical approaches10.1016/j.jmatprotec.2007.03.033 ↗
20. Totten · 2003
21. Further results on the nucleation of precipitates in the Al–Zn–Mg system10.1016/0001-6160(66)90229-X ↗
22. Effects of friction stir welding on microstructure of 7075 aluminum10.1016/S1359-6462(96)00344-2 ↗
23. Microstructural investigation of friction stir welded 7050-T651 aluminium10.1016/S1359-6454(02)00449-4 ↗
24. The precipitation sequence in Al–Mg–Si alloys10.1016/S1359-6454(98)00059-7 ↗
25. A sub-structural analysis of friction stir welded joints in an AA6056 Al-alloy in T4 and T6 temper conditions10.1016/j.msea.2006.12.055 ↗
26. Microstructural evolution of 6063 aluminum during friction-stir welding10.1007/s11661-999-0251-1 ↗
27. Ageing processes in Al–Mg–Si alloys during continuous heating10.2320/matertrans.43.246 ↗
28. Neutron diffraction measurements of time-dependent residual stresses generated by severe thermomechanical deformation10.1016/j.scriptamat.2009.05.040 ↗
29. A characterization for the flow behavior of as-extruded 7075 aluminum alloy by the improved Arrhenius model with variable parameters10.1590/S1516-14392012005000156 ↗