Effect of die design parameters on the deformation behavior in pure shear extrusion
Source abstract
Abstract
Abstract Influences of die design parameters in terms of diameter ratio and length of the deformation zone on the distribution of effective strain, filling fraction of the die exit channel and pressing load in pure shear extrusion (PSE) are studied using finite element method (FEM). Dimensional stability, pressing load and hardness measurements are used to validate the predictions of the simulation. Acceptable agreements between the predictions of simulation and experimental results are observed. It is found that strain is inhomogeneously distributed which increases from the center to the corners. Effective strain, inhomogeneity of strain, filling fraction of the die exit channel and pressing load are increased with increasing diameter ratio. In addition, the work-piece is deformed more homogeneously at lower pressing load by increasing the length of deformation zone. However, filling fraction of the die exit channel initially increases by the length of the deformation zone up to 60 mm after which it reduces. The optimum die design parameters covering a range of acceptable effective strain and strain homogeneity, filling fraction of the die exit channel and pressing load are proposed as being 60 mm and 2 for length of the deformation zone and diameter ratio, respectively.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Metallurgy and Material Forming · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (35)
Show source-provided references
1. Processing of nanostructured metals and alloys via plastic deformation10.1557/mrs2010.702 ↗
2. Properties and deformation behaviour of severe plastic deformed aluminium alloys10.1016/j.jmatprotec.2006.07.038 ↗
3. Microstructure and strength of pure Cu with large grains processed by equal channel angular pressing10.1016/j.matdes.2013.05.029 ↗
4. 3D FEM simulations for the homogeneity of plastic deformation in Al–Cu alloys during ECAP10.1016/j.msea.2009.10.032 ↗
5. Mapping subgrain sizes resulting from severe simple shear deformation10.1016/j.actamat.2011.09.055 ↗
6. Bulk nanostructured materials from severe plastic deformation10.1016/S0079-6425(99)00007-9 ↗
7. A novel severe plastic deformation method for fabricating ultrafine grained pure copper10.1016/j.matdes.2012.07.047 ↗
8. Investigation of texture and mechanical properties of copper processed by new route of equal channel angular pressing10.1016/j.matdes.2012.08.002 ↗
9. Ultra-fine grained bulk aluminum produced by accumulative roll-bonding (ARB) process10.1016/S1359-6462(98)00302-9 ↗
10. Effects of high shearing stress combined with high hydrostatic pressure
11. Finite element analysis of plastic deformation behavior during high pressure torsion processing10.1016/j.jmatprotec.2007.11.204 ↗
12. Materials processing by simple shear10.1016/0921-5093(95)09705-8 ↗
13. FEM and metallurgical analysis of modified 6082 aluminium alloys processed by multipass ECAP: influence of material properties and different process settings on induced plastic strain10.1016/j.jmatprotec.2008.04.013 ↗
14. Finite element analysis and optimization of equal channel angular pressing for producing ultra-fine grained materials10.1016/j.jmatprotec.2006.11.025 ↗
15. Combination of sever plastic deformation and precipitation hardening processes affecting the mechanical properties in Al–Mg–Si alloy10.1016/j.matdes.2014.12.011 ↗
16. Finite element analysis of plastic deformation in twist extrusion10.1016/j.commatsci.2012.03.035 ↗
17. Mechanical behaviour and microstructural evolution of constrained groove pressed nickel sheets10.1016/j.jmatprotec.2012.09.012 ↗
18. A comparison between equal channel angular pressing and asymmetric rolling of silver in the severe plastic deformation regime10.1016/j.msea.2012.09.018 ↗
19. Deformation behavior in Simple Shear Extrusion (SSE) as a new severe plastic deformation technique10.1016/j.msea.2009.08.051 ↗
20. Towards bulk nanostructured materials in pure shear10.1016/j.matlet.2014.09.114 ↗
21. A new severe plastic deformation technique based on pure shear10.1016/j.msea.2014.12.024 ↗
22. Severe plastic deformation: simple shear versus pure shear10.1016/S0921-5093(02)00066-7 ↗
23. Using high-pressure torsion for metal processing: fundamentals and applications10.1016/j.pmatsci.2008.03.002 ↗
24. Features of twist extrusion: method, structures & material properties10.4028/www.scientific.net/SSP.114.69 ↗
25. An investigation of hardness homogeneity throughout disks processed by high-pressure torsion10.1016/j.actamat.2010.09.034 ↗
26. Numerical experimental studies of the plastic strains distribution using subsequent direct extrusion after three twist extrusion passes10.1016/j.msea.2010.02.077 ↗
27. Investigation and numerical analysis of strain distribution in the twist extrusion of pure aluminum10.1007/s11837-011-0032-3 ↗
28. S.K. Lu, H.Y. Liu, L. Yu, Y.L. Jiang, J.H. Su, 3D FEM simulations for the homogeneity of plastic deformation in aluminum alloy HS6061-T6 during ECAP, in: 2011 SREE Conf Eng Model Simul CEMS 2011, 12, pp. 35–40. http://dx.doi.org/10.1016/j.proeng.2011.05.007.10.1016/j.proeng.2011.05.007 ↗
29. A modified die for equal channel angular pressing10.1016/j.jmatprotec.2008.07.022 ↗
30. A novel technique to increase strain distribution homogeneity for ECAPed materials10.1016/j.msea.2011.12.050 ↗
31. Analysis of plastic deformation behavior during back pressure equal channel angular pressing by the finite element method10.1016/j.commatsci.2013.04.054 ↗
32. B.V. Patil, U. Chakkingal, T.S. Prasanna Kumar, Effect of geometric parameters on strain, strain inhomogeneity and peak pressure in equal channel angular pressing – A study based on 3D finite element analysis, J. Manuf. Process n.d. doi:http://dx.doi.org/10.1016/j.jmapro.2014.07.010.10.1016/j.jmapro.2014.07.010 ↗
33. Optimum groove pressing die design to achieve desirable severely plastic deformed sheets10.1016/j.matdes.2009.07.008 ↗
34. DEFORMTM 3D Version 6.1 User’s Manual, Sci Form Technol Corp 2007.
35. Effect of die channel angle, friction and back pressure in the equal channel angular pressing using 3D finite element simulation10.1016/j.msea.2009.09.052 ↗