journal article·2016-11

Deep drawing of ZK60 magnesium sheets fabricated using ingot and twin-roll casting methods

Jae-Hyung Cho, Sang Su Jeong, Suk-Bong Kang

Materials & Design· Volume 110
Publisher page

Abstract

Abstract Deep drawing was carried out on two different ZK60 (Mg-Zn-Zr) magnesium sheets fabricated via ingot and twin-roll casting methods. The effects of the microstructure and texture on the deep drawability and the associated microstructural evolution of ZK60 alloys were examined. Twin-roll casted sheets with refined particles were stronger and showed greater elongation than ingot-casted sheets. Moreover, they were fully deep-drawn at lower temperatures than ingot-casted sheets, and the deep drawability of the ingot-casted sheets was better at a high deformation rate compared to that of the twin-roll casted sheets. During the deep drawing process, the ingot-casted sheets with large grains experienced more tensile twinning than the twin-roll casted sheets, and shear bands were observed. The twin-roll casted sheets revealed peak broadening of the basal texture along the TD and peak splitting along the RD. Thickness variations of the drawn cups showed that the twin-roll casted sheets resisted wall thinning more effectively than the ingot-casted sheets.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Dynamic recrystallisation and the development of microstructure during the high temperature deformation of mgnesium10.1016/0001-6160(82)90031-1 ↗
2. Modeling the temperature dependent e_ect of twinning on the behavior of magnesium alloys AZ31B sheet10.1016/j.msea.2006.03.160 ↗
3. Temperature dependency of slip and twinning in plane strain compression magnesium single crystals10.1016/j.actamat.2010.11.064 ↗
4. Application of texture simulation to understanding mechanical behavior of mg and solid solution alloys containing Li and Y10.1016/S1359-6454(01)00297-X ↗
5. Texture evolution of FCC sheet metals during deep drawing process10.1016/S0020-7403(99)00091-0 ↗
6. Simulation of earing during deep drawing of magnesium alloy AZ3110.1016/j.actamat.2006.09.007 ↗
7. Mechanical anisotropy and deep drawing behavior of AZ31 and ZE10 magnesium alloy sheets10.1016/j.actamat.2009.09.038 ↗
8. Deep drawability and drawing behaviour of AZ31 alloy sheets with di_erent initial texture10.1016/j.jallcom.2014.06.199 ↗
9. Mechanical anisotropy and deep drawing behaviors of AZ31 magnesium alloy sheets produced by unidirectional and cross rolling10.1016/j.jmatprotec.2014.08.020 ↗
10. The texture and anisotropy of magnesium-zine-rare earth alloy sheets10.1016/j.actamat.2006.11.013 ↗
11. Compressive deformation behavior at room temperature - 773K in Mg–0.2 mass% (0.035at.%)Ce alloy10.1016/j.actamat.2007.09.036 ↗
12. The recrystallization and texture of magnesium-zine-cerium alloys10.1016/j.scriptamat.2008.05.021 ↗
13. The influence of alloying additions and processing parameters on the rolling microstructures and textures of magnesium alloys10.1016/j.msea.2007.07.003 ↗
14. Texture and microstructure evolution during the symmetric and asymmetric rolling of AZ31B magnesium alloys10.1016/j.msea.2012.12.066 ↗
15. Enhanced plasticity of twin-roll cast ZK60 magnesium alloy through di_erential speed rolling10.1016/j.matdes.2009.03.040 ↗
16. Microstructure and mechanical properties of twin-roll cast Mg-4.5Al-1.0Zn sheets processed by di_erential speed rolling10.1016/j.matdes.2009.09.021 ↗
17. Feasibility study of twin roll casting process for magnesium alloys10.1016/j.jmatprotec.2007.04.009 ↗
18. Superplastic deformation behavior of twin-roll cast Mg-6Zn-1Mn-1Al alloy10.1016/j.scriptamat.2009.03.057 ↗
19. Microstructure and mechanical properties of Mg-Al-Mn-Ca sheet produced by twin roll casting and sequent warm rolling10.1016/j.jallcom.2010.07.183 ↗
20. Process parameters and roll separation force in horizontal twin rollcasting of aluminum alloys10.1016/j.jmatprotec.2014.11.031 ↗
21. Aging e_ect on texture evolution during warm rolling of ZK60 alloys fabricated by twin-roll casting10.1007/s11661-010-0336-x ↗
22. 2007
23. The onset of twinning in metals: a constitutive description10.1016/S1359-6454(01)00300-7 ↗
24. Low-temperature dynamic recrystallization occuring at a high deformation temperature during hot compression of twin-roll-cast Mg-5.51Zn-0.49Zr alloy10.1016/j.scriptamat.2008.11.023 ↗
25. Orientaion dependence of ebsd pattern quality
26. Deformation and recrystallization behaviors in magnesium alloys
27. A probabilistic twin nucleation model for hcp polycrystalline metals10.1098/rspa.2009.0661 ↗
28. Statistical analyses of deformation twinning in magnesium10.1080/14786431003630835 ↗
29. Stochastic modeling of twin nucleation in polycrystals - an application in hexagonal close-packed metals10.1016/j.ijplas.2013.11.005 ↗
30. Influence of texture on Hall-Petch relationships in an Mg alloy10.1016/j.actamat.2014.08.023 ↗