journal article·2022-05Open access

Design methodology of the Ni50Ti50 shape memory alloy beam actuator: Heat treatment, training and numerical simulation

Zhixiang Rao, Xiaoyuan Wang, Jiaming Leng, Zehong Yan, Xiaojun Yan

Materials & Design· Volume 217

Abstract

Shape memory alloy (SMA) beam actuators are widely used in morphing structures, which leads to a surgent demand for a comprehensive design method. Previous methods have not considered the heat treatment and the evolution of actuation performance during training. In this study, an in-depth investigation was conducted into the Ni50Ti50 (at%) SMA beam actuator from the perspective of heat treatment, training, numerical simulation for developing a comprehensive and novel design methodology. The proper heat treatment conditions that result in the relatively high actuation performance for the Ni50Ti50 SMA beam were determined. The dependence of the thermomechanical behavior evolution on the training load was established. Moreover, a numerical analysis method for the SMA beam actuator based on a 3-D constitutive model with tension-compression asymmetry considered was detailed, followed by the calibration of material parameters. A forward design method for the SMA beam actuator was proposed with the shape and actuation performance evolution during training under various training loads fully considered in the design process. The proposed design method was applied for a design case and the accuracy of the design results demonstrated its feasibility.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Shape Memory Alloy Transformations

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (49)

Show source-provided references
1. R. Pecora, I. Dimino, M. Bray et al., Chapter 15 - SMA for aeronautics. Shape Memory Alloy Engineering, second ed., Butterworth-Heinemann, Boston, 2021, pp. 527–559.10.1016/B978-0-12-819264-1.00015-7 ↗
2. An untethered mechanically-intelligent inchworm robot powered by a shape memory alloy oscillator10.1016/j.sna.2021.113115 ↗
3. Multifunctional properties of shape memory materials in civil engineering applications: A state-of-the-art review10.1016/j.jobe.2021.102657 ↗
4. F. Auricchio, E. Boatti, M. Conti et al., Chapter 19 - SMA biomedical applications. Shape Memory Alloy Engineering, second ed., Butterworth-Heinemann, Boston, 2021, pp. 627–658.10.1016/B978-0-12-819264-1.00019-4 ↗
5. Detailed design and life prediction methodology of novel SMA actuated repeatable launch locking protective device (RLLPD) for magnetically suspended flywheel (MSFW)10.1088/1361-665X/abed41 ↗
6. Beam-pipe coupling in particle accelerators by shape memory alloy rings10.1016/j.matdes.2016.11.101 ↗
7. Boeing's Variable Geometry Chevron, Morphing Aerostructure for Jet Noise Reduction
8. Shape memory microactuation design by substrate's reinforcement layers10.1016/j.matdes.2016.02.033 ↗
9. Morphing blades with embedded SMA strips: An experimental investigation10.1016/j.matdes.2015.07.175 ↗
10. Morphing Airfoil with Shape Memory Alloy Wire Actuators for Active Aerodynamic Load Control in Large Wind-Turbine Blades
11. Aerospace applications of shape memory alloys10.1243/09544100JAERO211 ↗
12. D.J. Hartl, D.C. Lagoudas, Characterization and 3-D Modeling of Ni60Ti SMA for Actuation of a Variable Geometry Jet Engine Chevron, Conference on Sensors and Smart Structures Technologies for Civil, Mechanical, and Aerospace Systems 2007 pt2, San Diego, California, United States, 2007.10.1117/12.715764 ↗
13. J.H. Mabe, R.H. Cabell, G.W. Butler, Design and Control of a Morphing Chevron for Takeoff and Cruise Noise Reduction, 11th AIAA/CEAS Aeroacoustics Conference. Monterey, California, US; Institute of Noise Control Engineering, 2005, pp. 1–15.10.2514/6.2005-2889 ↗
14. Experiments and modeling of variable camber guide vane embedded with shape memory alloy plate10.1088/1361-665X/abe846 ↗
15. Controlled shape-morphing metallic components for deployable structures10.1016/j.matdes.2021.109935 ↗
16. Effect of annealing on deformation-induced martensite stabilisation of NiTi10.1016/j.intermet.2007.09.003 ↗
17. The effect of martensite plasticity on the cyclic deformation of super-elastic NiTi shape memory alloy10.1088/0964-1726/23/1/015008 ↗
18. A micromechanical constitutive model based on crystal plasticity for thermo-mechanical cyclic deformation of NiTi shape memory alloys10.1016/j.ijplas.2013.01.001 ↗
19. Factors influencing the development of two-way shape memory in NiTi10.1016/0956-7151(90)90204-T ↗
20. Effect of training conditions and extended thermal cycling on nitinol two-way shape memory behavior10.1088/0964-1726/4/4/010 ↗
21. Superelastic and Shape Memory Effects in Laminated Shape-Memory-Alloy Beams10.2514/2.1918 ↗
22. Active shape/stress control of shape memory alloy laminated beams10.1016/j.compositesb.2013.09.018 ↗
23. A model for shape memory alloy beams accounting for tensile compressive asymmetry10.1177/1045389X19873407 ↗
24. On superelastic bending of shape memory alloy beams10.1016/j.ijsolstr.2013.01.035 ↗
25. Constitutive modeling and structural analysis considering simultaneous phase transformation and plastic yield in shape memory alloys10.1088/0964-1726/18/10/104017 ↗
26. Use of a Ni60Ti shape memory alloy for active jet engine chevron application: I. Thermomechanical characterization10.1088/0964-1726/19/1/015020 ↗
27. Use of a Ni60Ti shape memory alloy for active jet engine chevron application: II. Experimentally validated numerical analysis10.1088/0964-1726/19/1/015021 ↗
28. Modeling fluid structure interaction with shape memory alloy actuated morphing aerostructures
29. Otsuka · 1998
30. The effects of shape-setting on transformation temperatures of pseudoelastic shape memory alloy springs
31. Control of phase transformations and microstructure for optimum realization of one-way and two-way shape memory effects in removable surgical clips10.1016/j.matdes.2017.09.024 ↗
32. Rapidly solidified and optimally constraint-aged Ni51Ti49 shape memory alloy aiming at making a purpose-designed bio-actuator10.1016/j.matdes.2017.01.001 ↗
33. Effects of Composition and Post Heat Treatment on Shape Memory Characteristics and Mechanical Properties for Laser Direct Deposited Nitinol10.1007/s40516-019-0079-5 ↗
34. Design of TiNi alloy two-way shape memory coil extension spring10.1016/S0921-5093(02)00474-4 ↗
35. Effects of training on the thermomechanical behavior of NiTiHf and NiTiZr high temperature shape memory alloys10.1016/j.msea.2020.139857 ↗
36. Experimental study on whole-life one-way shape memory cyclic degradation and fatigue failure of NiTi shape memory alloy10.1016/j.mtcomm.2020.101621 ↗
37. A thermodynamical constitutive model for shape memory materials. Part I. The monolithic shape memory alloy10.1016/S0749-6419(96)00030-7 ↗
38. A 3-D constitutive model for shape memory alloys incorporating pseudoelasticity and detwinning of self-accommodated martensite10.1016/j.ijplas.2007.03.011 ↗
39. Effect of tension-compression asymmetry and partial transformation on the response of shape memory alloy beam structures10.1117/12.2563123 ↗
40. Lagoudas · 2008
41. Methodology for the estimation of material damping as applied to superelastic shape memory alloy mini-springs10.1016/j.matdes.2018.11.012 ↗
42. ABAQUS Standard User’s Manual
43. Recovery stress formation in FeMnSi based shape memory alloys: Impact of precipitates, texture and grain size10.1016/j.matdes.2017.11.006 ↗
44. Stabilisation of martensite due to shear deformation via variant reorientation in polycrystalline NiTi10.1016/S1359-6454(00)00129-4 ↗
45. Modeling, Fabrication, and Testing of a SMA Hybrid Composite Jet Engine Chevron Concept10.1177/1045389X06058795 ↗
46. Shape optimization of SMA structures with respect to fatigue10.1016/j.matdes.2019.108456 ↗
47. Finite rotation effects in numerical integration of rate constitutive equations arising in large-deformation analysis10.1002/nme.1620151210 ↗
48. Thermomechanical modeling of polycrystalline SMAs under cyclic loading, Part I: theoretical derivations10.1016/S0020-7225(98)00113-X ↗
49. Modeling of transformation-induced plasticity and its effect on the behavior of porous shape memory alloys. Part I: constitutive model for fully dense SMAs10.1016/j.mechmat.2003.08.006 ↗