Pore space of steatite ceramics triggered by the allowance of natural fibers: High-resolution X-ray microscopy analysis and related thermo-mechanical properties
Source abstract
Abstract
A large number (greater than 150) of porous steatite ceramic rods were prepared using different types of renewable plant fiber products as pore-forming agent with mass contents ranging from 2 to 10%. In addition, dense steatite ceramics were synthesized for comparison within a gas furnace at sintering temperatures between 1300 and 1350 °C. High-resolution 3D X-ray microscopy facilitated a non-destructive, direct investigation of the three-dimensional pore space and microstructure. By using image-based pore space analysis, various pore space parameters, such as, e.g., pore volume, pore-size distribution, and pore connectivity were determined. In addition to the characterization of the pore space, phase analysis, structural and chemical investigations were carried out by X-ray powder diffraction, electron microscopy, Fourier-transform infrared, Raman and X-ray spectroscopy. Finally, to evaluate the influence of characteristics on the physical properties, elastic, strength and thermal properties were determined. With the increase of porosity, the flexural strength and thermal conductivity values decrease from σf = 123 ± 8 to 37 ± 5 MPa and λ = 3.22 ± 0.02 to 1.77 ± 0.02 W/(m·K), respectively. The obtained experimental results were discussed by means of micromechanical models, highlighting the effect of pore-space morphologies on the physical performance of porous steatite ceramics.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced ceramic materials synthesis · Recycling and utilization of industrial and municipal waste in materials production · Thermal properties of materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (57)
Show source-provided references
1. On the crystal structure and compressional behavior of talc: a mineral of interest in petrology and material science10.1007/s00269-012-0554-4 ↗
2. Sintering behavior of steatite materials with barium carbonate flux10.1016/j.ceramint.2006.04.015 ↗
3. Non-hydrostatic stress field orientation inferred from orthopyroxene (Pbca) to low-clinoenstatite (P21/c) inversion in partially dehydrated serpentinites10.2138/am-2018-6362 ↗
4. Protoenstatite: A new mineral in Oregon sunstones with “watermelon” colors10.2138/am-2017-6186 ↗
5. Correlation between MgSiO3 phases and mechanical durability of steatite ceramics10.1016/j.jeurceramsoc.2003.12.030 ↗
6. The synthesis and crystal structure of a magnesium-lithium-scandium protopyroxene
7. Nature of the luminescence of SNC steatite ceramic10.1007/s10512-021-00812-w ↗
8. Effect of indenter material on reliability of all-ceramic crowns10.1016/j.jmbbm.2020.103831 ↗
9. Influence of antagonist material on fatigue and fracture resistance of zirconia crowns10.1055/s-0040-1708228 ↗
10. P. Colombo, In Praise of Pores, Science 322 (2008) 5900, 381–383. https://doi.org/10.1126/science.1162962.10.1126/science.1162962 ↗
11. Fabrication of porous bioceramics with porosity gradients similar to the biomodal structure of cortical and cancellous bone
12. Porous bioceramics produced by inkjet 3D printing: Effect of printing ink formulation on the ceramic macro and micro porous architectures control10.1016/j.compositesb.2018.08.047 ↗
13. Effect of the morphology and pore structure of porous building materials on photocatalytic oxidation of air pollutants10.1016/j.apcatb.2018.01.029 ↗
14. Commonly used porous building materials: Geomorphic pore structure and fluid transport10.1061/(ASCE)MT.1943-5533.0000706 ↗
15. Function-led design of new porous materials10.1126/science.aaa8075 ↗
16. Porous crystals as membranes10.1126/science.aba4997 ↗
17. Balancing volumetric and gravimetric uptake in highly porous materials for clean energy10.1126/science.aaz8881 ↗
18. 3D-printed MOF-derived hierarchically porous frameworks for practical high-energy density Li–O2 batteries10.1002/adfm.201806658 ↗
19. Hierarchical porous materials: catalytic applications10.1039/C2CS35378D ↗
20. Porous materials applied in nonaqueous Li–O2 batteries: Status and perspectives10.1002/adma.202002559 ↗
21. Design and processing of porous materials for electronic applications10.1098/rsta.2005.1694 ↗
22. Dynamic fracture evolution of tight sandstone under uniaxial compression in high resolution 3D X-ray microscopy10.1016/j.petrol.2020.107585 ↗
23. Morphology changes in Fe-Cr porous alloys upon high-temperature oxidation quantified by X-ray tomographic microscopy10.1016/j.matdes.2022.110492 ↗
24. Digital light processing of β-tricalcium phosphate bioceramic scaffolds with controllable porous structures for patient specific craniomaxillofacial bone reconstruction10.1016/j.matdes.2022.110558 ↗
25. Design of macropore structure and micro-nano topography to promote the early neovascularization and osteoinductivity of biphasic calcium phosphate bioceramics10.1016/j.matdes.2022.110581 ↗
26. 3D X-ray micro-computed tomography imaging for the microarchitecture evaluation of porous metallic implants and scaffolds10.1016/j.micron.2020.102994 ↗
27. Experimental study on the effect of moisture content on bituminous coal porosity based on 3D reconstruction of computerized tomography10.1007/s11053-019-09528-y ↗
28. NiO/Ni nanocomposites embedded in 3D porous carbon with high performance for lithium-ion storage10.1007/s10853-019-04075-6 ↗
29. Comparing non-destructive 3D X-ray computed tomography with destructive optical microscopy for microstructural characterization of fiber reinforced composites10.1016/j.compscitech.2019.107843 ↗
30. Characterizing porous microaggregates and soil organic matter sequestered in allophanic paleosols on Holocene tephras using synchrotron-based X-ray microscopy and spectroscopy10.1038/s41598-021-00109-9 ↗
31. Effect of microwave pre-curing technology on carbide slag-fly ash autoclaved aerated concrete (CS-FA AAC): Porosity rough body formation, pore characteristics and hydration products10.1016/j.conbuildmat.2020.120112 ↗
32. Insight Software Consortium, The ITK Software Guide, Kitware Inc. (2017). https://itk.org/ITKSoftwareGuide/html.
33. J.-M. Mirebeau, J. Fehrenbach, L. Risser, S. Tobji, Anisotropic diffusion in ITK, arXiv preprint arXiv:1503.00992 (2015). https://arxiv.org/abs/1503.00992.10.54294/en3833 ↗
34. R. Beare, Histogram-based thresholding – some missing methods, Insight J. (2011). http://hdl.handle.net/10380/3279.10.54294/efycla ↗
35. Picture thresholding using an iterative selection method10.1109/TSMC.1978.4310039 ↗
36. Pore-network extraction from micro-computerized-tomography images10.1103/PhysRevE.80.036307 ↗
37. A profile refinement method for nuclear and magnetic structures10.1107/S0021889869006558 ↗
38. A Fundamental Parameters Approach to X-ray Line-Profile Fitting10.1107/S0021889891010804 ↗
39. VESTA 3 for the three-dimensional visualization of crystal, volumetric and morphology data10.1107/S0021889811038970 ↗
40. S.A.S., LabSpec Version 5, Horiba Jobin Yvon, Longjumeau Cedex, France, 2010.
41. Bilbao crystallographic server: Useful databases and tools for phase transitions studies10.1080/0141159031000076110 ↗
42. High temperature single crystal X-ray diffraction studies of the ortho-proto phase transition in enstatite, Mg2Si2O6 at 1360 K10.1007/BF00202770 ↗
43. High temperature crystal structure refinements of low-clinoenstatite up to 700 degrees C
44. The pressure behavior of alpha-cristobalite
45. Lattice dynamics and Raman spectroscopy of protoenstatite Mg2Si2O6
46. Rapid identification of steatite-enstatite polymorphs at various temperatures10.1016/j.jeurceramsoc.2008.03.009 ↗
47. Infrared spectra of pyroxenes (crystalline chain silicates) at room temperature10.1093/mnras/staa2227 ↗
48. Microstructure and mechanical properties of porous alumina ceramics fabricated by the decomposition of aluminum hydroxide10.1111/j.1151-2916.2001.tb01065.x ↗
49. Determination of stress concentration factors in porous materials10.1007/BF00275423 ↗
50. Concentration of stress around spherical and cylindrical inclusions and flaws10.1115/1.4012173 ↗
51. Kolsky · 1953
52. Average stress in matrix and average elastic energy of materials with misfitting inclusions10.1016/0001-6160(73)90064-3 ↗
53. The elasticity of an isotropic aggregate of anisotropic cubic crystals10.1115/1.4010899 ↗
54. Berechnung der elastischen Konstanten des Vielkristalls aus den Konstanten des Einkristalls10.1007/BF01337948 ↗
55. A variational approach to the theory of the effective magnetic permeability of multiphase materials10.1063/1.1728579 ↗
56. Flash method of determining thermal diffusivity, heat capacity, and thermal conductivity10.1063/1.1728417 ↗
57. Maxwell · 1873