journal article·2016-06

Incorporation of asymmetric yield and hardening behaviour in axisymmetric elastoplastic problems

Mohammad Ali Khayamian, Behzad Behravesh, Hamid Jahed

Materials & Design· Volume 99
Publisher page

Abstract

Abstract Within the context of total deformation plasticity, an axisymmetric model is developed for materials with asymmetric yield and hardening behaviours. The model employs the variable material properties (VMP) method which is an axisymmetric method of analysis widely used for problems such as pressure vessels. The original VMP method is applicable only to materials with symmetric hardening behaviour. In this study, the VMP method is extended to materials with asymmetric yield and hardening to examine the importance of considering the asymmetry within elastoplastic analyses. The asymmetric and isotropic Cazacu-Barlat yield criterion is employed. For residual stress calculations, actual unloading stress-strain curves obtained from experiments are directly incorporated into the proposed method. The results of the proposed model are first compared to the experimental results from a cylindrical magnesium specimen loaded under internal pressure and axial push/pull. The results are in very good agreement for the load cases where the stress state is uniaxial; the results deviate slightly for multi-axial stress states. An extensive comparison is made between the proposed asymmetric solution results and the results of symmetric solutions. The symmetric solutions adopt von Mises yield criterion and a symmetric hardening rule, e.g., isotropic and kinematic. The residual stress field results demonstrate that, for asymmetric materials, the results obtained from a symmetric solution can be significantly different under biaxial loading, and consideration of an asymmetric yield criterion along with an asymmetric hardening model is necessary. The loading and unloading responses of a thick-walled cylinder under internal pressure obtained from the proposed model are compared to those obtained from the LS-DYNA, MAT124 model. It is shown that the stress distributions are substantially different both after loading and unloading reversals.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Metal Forming Simulation Techniques · Fatigue and fracture mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. Gupta · 2011
2. Research for a “New Age of Magnesium” in the automotive industry10.1016/S0924-0136(01)00780-4 ↗
3. Magnesium: properties—applications—potential10.1016/S0921-5093(00)01351-4 ↗
4. Mechanical anisotropy of extruded Mg–6% Al–1% Zn alloy10.1016/j.msea.2004.02.020 ↗
5. Anisotropy of dynamic behavior of extruded AZ31 magnesium alloy10.1016/j.msea.2010.01.023 ↗
6. A theory of the yielding and plastic flow of anisotropic metals10.1098/rspa.1948.0045 ↗
7. Hardening evolution of AZ31B Mg sheet10.1016/j.ijplas.2006.03.005 ↗
8. Tensile-compressive yield asymmetries in high strength wrought magnesium alloys10.1016/0956-716X(94)90159-7 ↗
9. The strength-differential effect in plasticity10.1016/0020-7683(84)90047-7 ↗
10. Abaqus · 2014
11. LS-DYNA · 2006
12. An efficient constitutive model for room-temperature, low-rate plasticity of annealed Mg AZ31B sheet10.1016/j.ijplas.2009.11.001 ↗
13. Constitutive law for AZ31B Mg alloy sheets and finite element simulation for three-point bending10.1016/j.ijmecsci.2008.08.004 ↗
14. An elasto-plastic constitutive model for evolving asymmetric/anisotropic hardening behavior of AZ31B and ZEK100 magnesium alloy sheets considering monotonic and reverse loading paths10.1016/j.ijplas.2015.03.004 ↗
15. A constitutive model for HCP materials deforming by slip and twinning: application to magnesium alloy AZ31B10.1016/S0749-6419(03)00039-1 ↗
16. Plastic anisotropy and the role of non-basal slip in magnesium alloy AZ31B10.1016/j.ijplas.2004.05.018 ↗
17. Quasi-static and fatigue behavior of extruded ME21 and twin roll cast AZ31 magnesium sheet metals10.1016/j.msea.2013.09.088 ↗
18. Tension–compression yield asymmetry in as-cast magnesium alloy10.1016/j.jallcom.2014.07.164 ↗
19. Behravesh · 2013
20. An axisymmetric method of elastic-plastic analysis capable of predicting residual stress field10.1115/1.2842303 ↗
21. Loading and unloading behaviour of a thermoplastic disc10.1016/S0308-0161(01)00079-5 ↗
22. Elasto-plastic stresses in a functionally graded rotating disk10.1115/1.4006023 ↗
23. Actual unloading behavior and its significance on residual stress in machined autofrettaged tubes10.1115/1.1593070 ↗
24. Residual stresses in autofrettaged vessel made of functionally graded material10.1016/j.engstruct.2009.07.019 ↗
25. An asymmetric elastic–plastic analysis of the load-controlled rotating bending test and its application in the fatigue life estimation of wrought magnesium AZ31B10.1016/j.ijfatigue.2014.02.012 ↗
26. A criterion for description of anisotropy and yield differential effects in pressure-insensitive metals10.1016/j.ijplas.2003.11.021 ↗
27. A theory of the yielding and plastic flow of anisotropic metals10.1098/rspa.1948.0045 ↗
28. Material modeling of AZ31 Mg sheet considering variation of r-values and asymmetry of the yield locus10.1016/j.msea.2012.04.009 ↗
29. Biaxial deformation of the magnesium alloy AZ8010.1007/s11661-013-1707-x ↗
30. Cyclic axial and cyclic torsional behaviour of extruded AZ31B magnesium alloy10.1016/j.ijfatigue.2011.04.012 ↗
31. Strain controlled cyclic deformation behavior of an extruded magnesium alloy10.1016/j.msea.2008.05.016 ↗
32. LS-DYNA · 2014
33. Design of lightweight magnesium car body structure under crash and vibration constraints10.1016/j.jma.2014.05.005 ↗