A novel approach for zero material loss (zero flash) and uniform cross-section during friction stir welding of dissimilar thickness Cu and Al alloys
Source abstract
Abstract
A novel approach for getting a uniform weld cross-section and flash-free joint with the help of friction stir welding (FSW) is implemented. The influence of the tool tilt angle and rotational speed on the macrostructure, microstructure, and mechanical properties was investigated. Mechanical characterization techniques like an optical microscope, FESEM, profilometer, tensile test, bent test, and XRD analysis were used to evaluate the joint properties. A maximum tensile strength of 108.91 MPa was achieved, which led to a joint efficiency of 96.38 %. A maximum bending angle of 107˚ was achieved for samples S5 and S6. The Al/Cu mixed region in the stir zone displayed a maximum micro-hardness of 152.26 HV whereas a minimum micro-hardness of 33.57 HV was achieved in the HAZ along aluminium side. Welds prepared at a rotational speed of 540 RPM and a tool tilt angle of 4.5˚results in an almost flash-free joint.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (27)
Show source-provided references
1. Senior · 1994
2. Dissimilar joining of aluminum to copper using ultrasonic welding10.1080/10426914.2016.1221101 ↗
3. Dissimilar friction stir welding of Al to non-Al metallic materials: an overview10.1016/j.matchemphys.2022.126371 ↗
4. A comparative study on the microstructure development of friction stir welded 304 austenitic, 430 ferritic, and 2205 duplex stainless steels10.1016/j.matchemphys.2019.121833 ↗
5. Role of friction stir welding - traveling speed in enhancing the corrosion resistance of aluminum alloy10.1016/j.matchemphys.2016.02.004 ↗
6. Investigation of microstructures and fatigue properties of friction stir welded Al-Mg alloy10.1016/j.matchemphys.2005.09.019 ↗
7. Aging of medium strength aluminum alloy friction stir welds produced by different process parameter after tensile strain hardening10.1016/j.matchemphys.2014.06.068 ↗
8. Influence of WC-based pin tool profile on microstructure and mechanical properties of AA1100 FSW welds10.3390/technologies8020034 ↗
9. Defect formation and material flow in friction stir welding10.1016/j.euromechsol.2019.103912 ↗
10. Influence of copper plate positioning, zero tool offset, and bed conditions in friction stir welding of dissimilar Al-Cu alloys with different thicknesses10.1016/j.cirpj.2022.04.001 ↗
11. Joining aluminium alloys dissimilar in thickness by friction stir welding and fusion processes10.1007/BF03266476 ↗
12. Joint strength evaluation of friction stir welded Al-Cu dissimilar alloys10.1016/j.measurement.2019.07.019 ↗
13. Influence of copper plate positioning, zero tool offset, and bed conditions in friction stir welding of dissimilar Al-Cu alloys with different thicknesses10.1016/j.cirpj.2022.04.001 ↗
14. Concurrent influences of tool offset and ultrasonic vibration on the joint quality and performance of dissimilar Al/Cu friction stir welds10.1016/j.jmrt.2021.07.009 ↗
15. Enhancing metallurgical and mechanical properties of friction stir butt welded joints of Al–Cu via cold sprayed Ni interlayer10.1016/j.msea.2021.140992 ↗
16. Experimental study on micro-friction stir welding of dissimilar butt joints between Al 1050 and pure copper10.1007/s13632-021-00771-5 ↗
17. Microstructural evolution and mechanical properties of the Al–Cu dissimilar joint enhanced by stationary-dynamic shoulder friction stir welding10.1016/j.jmatprotec.2021.117402 ↗
18. Microstructure, mechanical and electrical properties of dissimilar friction stir welded 2024 aluminum alloy and copper joints10.1016/j.jmrt.2021.07.058 ↗
19. Material-flow behavior during friction-stir welding of 6082-T6 aluminum alloy10.1007/s00170-016-8603-7 ↗
20. Recent advances in friction-stir welding - process, weldment structure and properties10.1016/j.pmatsci.2008.05.001 ↗
21. Effect of tool tilt angle and tool plunge depth on mechanical properties of friction stir welded AA 5083 joints10.4028/www.scientific.net/AMM.493.709 ↗
22. Dissimilar friction stir welding of Ti – 6Al – 4V alloy and aluminum alloy employing a modified butt joint configuration : influences of process variables on the weld interfaces and tensile properties10.1016/j.matdes.2013.07.019 ↗
23. A general strategy for the reliable joining of Al/Ti dissimilar alloys via ultrasonic assisted friction stir welding10.1016/j.jmst.2018.09.022 ↗
24. Dissimilar friction-stir welding of 430 stainless steel and 6061 aluminum alloy: microstructure and mechanical properties of the joints
25. Friction stir welding of aluminium alloys10.1179/174328009X411136 ↗
26. Joint strength evaluation of friction stir welded Al-Cu dissimilar alloys10.1016/j.measurement.2019.07.019 ↗
27. Effect of T6-treatments on microstructure and mechanical properties of forged Al-4.4Cu-0.7Mg-0.6Si alloy10.1016/S1003-6326(17)60282-6 ↗