journal article·2021-10

Strain rate sensitivity behaviour of Fe–21Cr-1.5Ni–5Mn alloy and its constitutive modelling

Tushar Ramdas Dandekar, Rajesh Kisni Khatirkar, Aman Gupta, Nitish Bibhanshu, Alok Bhadauria, Satyam Suwas

Publisher page

Abstract

Abstract In the present investigation, hot deformation behaviour of Fe–21Cr-1.5Ni–5Mn alloy was studied by performing isothermal unidirectional hot compression tests. The tests were carried out at strain rates of 0.01, 0.1, 1, 5 and 10 s−1 and at temperatures of 675, 750, 825, 900, 975 and 1050 °C. The samples were deformed up to 50% height reduction (e = 0.7). The flow softening behaviour was modelled using Arrhenius hyperbolic sine law approach. The predicted flow stresses and the experimental flow stresses were found to be comparable indicating that the developed model can accurately portray flow behaviour of Fe–21Cr-1.5Ni–5Mn alloy. As-received and deformed specimens showed elongated grain structure. The correlation coefficient (R2) of the experimental and predicted results for Arrhenius hyperbolic sine law model was ~0.97, while the average absolute relative error (AARE) was found to be 7.31%. The hot deformation activation energy for peak stress was found to be 508.3 kJ mol−1. The maximum value of ‘m’ (0.227) was obtained in the temperature range 975 °C–1050 °C and strain rates between 0.1 s−1 to 1 s−1. ‘m’ value between 0.1 and 0.2 is considered to be optimum for hot working. Deformation at 975 °C also gave the best match between experimental and predicted flow stress with m values between 0.1 and 0.2 and hence was considered optimum.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (65)

Show source-provided references
1. Strain induced martensitic transformation of Fe–20Cr–5Mn–0.2Ni duplex stainless steel during cold rolling: effects of nitrogen addition10.1016/j.msea.2011.04.038 ↗
2. Multistep cross rolling of UNS S32101 steel: microstructure, texture, and magnetic properties10.1007/s11665-021-05510-z ↗
3. Effect of austenitic texture on tensile behavior of lean duplex stainless steel with transformation induced plasticity (TRIP)10.1016/j.msea.2016.11.001 ↗
4. Effect of heat treatment on transformation-induced plasticity of economical Cr19 duplex stainless steel10.1016/j.matdes.2013.12.019 ↗
5. Effect of annealing temperature on transformation induced plasticity effect of a lean duplex stainless steel10.1016/j.matchar.2013.02.003 ↗
6. Super duplex stainless steels10.1179/mst.1992.8.8.685 ↗
7. Alvarez-Armas · 2009 · 31 · 115
8. Alternative process to manufacture austenitic-ferritic stainless steel wires10.1016/j.matlet.2004.12.026 ↗
9. Verlinden · 2007 · 417
10. Deformation characteristic and prediction of flow stress for as-cast 21Cr economical duplex stainless steel under hot compression10.1016/j.matdes.2013.04.065 ↗
11. Microstructure evolution in SAF 2507 super duplex stainless steel
12. Microstructural and mechanical behavior of a duplex stainless steel under hot working conditions10.1007/s11661-998-0205-z ↗
13. Suwas · 2014 · 207
14. Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions10.1016/j.pmatsci.2013.09.002 ↗
15. Influence of microstructure on the flow behavior of duplex stainless steels at high temperatures10.1007/s11661-000-0254-4 ↗
16. The influence of alloying, temperature, and related effects on the stacking fault energy10.1007/BF03038370 ↗
17. Hot deformation characteristics of 2205 duplex stainless steel based on the behavior of constituent phases10.1016/j.matdes.2009.06.028 ↗
18. Hot deformation behavior of as-cast 2101 grade lean duplex stainless steel and the associated changes in microstructure and crystallographic texture10.1007/s11661-016-3759-1 ↗
19. Effect of δ-ferrite co-existence on hot deformation and recrystallization of austenite10.1007/s10853-008-2907-4 ↗
20. Hot ductility and microstructure in casted 2205 duplex stainless steels10.1016/j.msea.2009.02.022 ↗
21. A mechanism of ferrite softening in a duplex stainless steel deformed in hot torsion10.1016/S0921-5093(97)00087-7 ↗
22. Effect of hot deformation mode on the microstructure evolution of lean duplex stainless steel 210110.1016/j.msea.2013.03.036 ↗
23. Investigation of hot deformation behavior of duplex stainless steel grade 250710.1007/s11661-016-3829-4 ↗
24. Strain rate sensitivity behaviour of a chrome-nickel austentic-ferritic steel and its constitutive modelling10.2355/isijinternational.ISIJINT-2018-051 ↗
25. Flow stress behavior of porous FVS0812 aluminum alloy during hot-compression10.1016/j.mechrescom.2005.05.008 ↗
26. A simplified approach for developing constitutive equations for modeling and prediction of hot deformation flow stress10.1007/s11661-015-3006-1 ↗
27. A comparative study on constitutive relationship of as-cast 904L austenitic stainless steel during hot deformation based on Arrhenius-type and artificial neural network models10.1016/j.commatsci.2012.07.028 ↗
28. Constitutive equations for prediction of the flow behaviour of duplex stainless steels10.1016/j.msea.2010.03.029 ↗
29. A physically-based constitutive model for a nitrogen alloyed ultralow carbon stainless steel10.1016/j.commatsci.2014.10.044 ↗
30. Constitutive behaviors of magnesium and Mg–Zn–Zr alloy during hot deformation10.1016/j.matchemphys.2014.12.023 ↗
31. Hot deformation behavior, dynamic recrystallization, and physically-based constitutive modeling of plain carbon steels10.1016/j.msea.2015.03.104 ↗
32. Dynamic restoration mechanism and physically based constitutive model of 2050 Al–Li alloy during hot compression10.1016/j.jallcom.2015.07.182 ↗
33. Constitutive analysis of Mg–Al–Zn magnesium alloys during hot deformation10.1016/j.mechmat.2014.07.004 ↗
34. A physically-based constitutive model for hot deformation of Ti-10-2-3 alloy10.1016/j.jallcom.2016.11.208 ↗
35. Quantification of the strengthening effect of rare earth elements during hot deformation of Mg-Gd-Y-Zr magnesium alloy10.1016/j.jmrt.2015.03.001 ↗
36. Physically based modeling and characterization of hot deformation behavior of twinning-induced plasticity steels bearing vanadium and niobium10.1016/j.msea.2017.07.038 ↗
37. Physically based constitutive analysis to predict flow stress of medium carbon and vanadium micro alloyed steels10.1016/j.msea.2014.02.068 ↗
38. Constitutive description of 7075 aluminum alloy during hot deformation by apparent and physically-based approaches10.1007/s11665-015-1389-1 ↗
39. Physically based constitutive analysis and microstructural evolution of AA7050 aluminum alloy during hot compression10.1016/j.matdes.2016.06.023 ↗
40. Microstructure study and constitutive modeling of Ti–6Al–4V alloy at elevated temperatures10.1016/j.matdes.2013.08.006 ↗
41. A simple Zerilli–Armstrong constitutive equation for modeling and prediction of hot deformation flow stress of steels10.1016/j.mechmat.2015.11.013 ↗
42. Dislocation mechanics-based constitutive equations10.1007/s11661-004-0201-x ↗
43. Standard Practice for Preparation of Metallographic Specimens 1995 E3-95 (PA, USA: ASTM).
44. Aliya · 2018
45. Humphreys · 2004 · 534
46. Constitutive modeling for hot working behavior of SP-700 titanium alloy10.1007/s11665-019-04355-x ↗
47. Deformation behaviour of beta titanium alloy Ti-10 V-4.5Fe-1.5Al in hot upset forging10.1016/S0921-5093(01)01982-7 ↗
48. Mechanical properties of SP-700 titanium alloy at room temperature
49. Modeling the hot working behavior of near-α titanium alloy IMI83410.1016/j.pnsc.2013.11.004 ↗
50. Campbell · 2008 · 117
51. Gunn · 1997 · 56
52. Hot deformation behavior of microstructural constituents in a duplex stainless steel during high-temperature straining10.1007/s12613-013-0820-6 ↗
53. Hot deformation behavior, dynamic recrystallization, and physically-based constitutive modeling of plain carbon steels10.1016/j.msea.2015.03.104 ↗
54. Constitutive relationships for hot deformation of austenite10.1016/j.actamat.2011.07.008 ↗
55. Ma · Ironmak. Steelmak. · 2016 · 43 · 8810.1179/1743281215Y.0000000053 ↗
56. Role of twinning on dynamic recrystallization and microstructure during moderate to high strain rate hot deformation of a Ti-modified austenitic stainless steel10.1007/s11661-011-1012-5 ↗
57. Investigation on hot compression precipitation and recrystallization behavior of 23.7Cr–2.2Ni–1.3Mo–14Mn–0.26N high-manganese low-nickel duplex stainless steel10.1002/srin.202000385 ↗
58. High temperature deformation behavior of Nb–1wt.%Zr alloy10.1016/j.matdes.2015.12.077 ↗
59. Theory of the tensile test10.1016/0001-6160(67)90211-8 ↗
60. Plastic instability in rate-dependent materials10.1016/0022-5096(67)90008-7 ↗
61. Plastic instability in tension and compression10.1016/0001-6160(76)90039-0 ↗
62. Dynamic recrystallization during the transient deformation of a vanadium micro alloyed steel10.1016/0001-6160(83)90053-6 ↗
63. Optimisation of cold and warm workability of commercially pure titanium using dynamic materials model (DMM) instability maps10.1016/j.jmatprotec.2007.09.038 ↗
64. Optimization of hot working parameters for thermo-mechanical processing of modified 9Cr–1Mo (P91) steel employing dynamic materials model10.1016/j.msea.2011.03.025 ↗
65. Processing maps for hot deformation of a high-Mn TWIP steel: a comparative study of various criteria based on dynamic materials model10.1016/j.msea.2013.08.036 ↗