Corrosion behavior of pyrocarbon coatings exposed to Al2O3–SiO2 gels containing ammonium nitrate
Source abstract
Abstract
Abstract The corrosion behavior of pyrocarbon (PyC) coatings exposed to Al 2 O 3 –SiO 2 gels containing ammonium nitrate (AN) was investigated. The formation of nitrogen oxides during the decomposition of AN could enable the oxidation of PyC at relatively low temperature. After corrosion by the gels, severe attack was observed and the surface roughness of the coatings increased remarkably. The degree of crystallization decreased while that of disorder increased in PyC. Finally, PyC coatings were introduced into three-dimensional all-oxide fiber-reinforced composites. We found that the resulting porous coatings were favorable to the fiber/matrix debonding, thereby contributing to the performance improvement.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced ceramic materials synthesis · Diamond and Carbon-based Materials Research · Polymer Nanocomposites and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. State of the art and perspectives for oxide/oxide composites10.1016/S1270-9638(02)00015-9 ↗
2. Interfaces in oxide-fibre-based composites10.1016/j.cossms.2006.05.004 ↗
3. Oxidation behaviors of C/SiC in the oxidizing environments containing water vapor10.1016/S0921-5093(02)00644-5 ↗
4. Ceramics for future power generation technology: fiber reinforced oxide composites10.1016/S1359-0286(01)00017-1 ↗
5. Developments in oxide fiber composites10.1111/j.1551-2916.2006.01342.x ↗
6. The design of the fibre–matrix interfacial zone in ceramic matrix composites10.1016/S1359-835X(97)00128-0 ↗
7. Mullite (Nextel™720) fibre-reinforced mullite matrix composites exhibiting favourable thermomechanical properties10.1016/S0955-2219(01)00531-3 ↗
8. Effects of SiC interphase by chemical vapor deposition on the properties of C/ZrC composite prepared via precursor infiltration and pyrolysis route10.1016/j.matdes.2012.09.019 ↗
9. Fracture behaviour of mullite fibre reinforced-mullite matrix composites under quasi-static and ballistic impact loading10.1016/j.compscitech.2004.08.002 ↗
10. Porous yttrium aluminum garnet fiber coatings for oxide composites10.1111/j.1151-2916.2002.tb00517.x ↗
11. Development of ZrO2 interfaces for all-oxide composites10.1016/j.compscitech.2011.11.002 ↗
12. Fugitive interfacial carbon coatings for oxide/oxide composites10.1111/j.1151-2916.2000.tb01194.x ↗
13. Control of interface properties in oxide composites via fugitive coatings10.1111/j.1551-2916.2008.02746.x ↗
14. Mechanical and microwave dielectric properties of SiCf/SiC composites with BN interphase prepared by dip-coating process10.1016/j.jeurceramsoc.2012.02.009 ↗
15. Chemical vapour deposition of coatings10.1016/S0079-6425(01)00009-3 ↗
16. Mechanical properties of 3D KD-I SiCf/SiC composites with engineered fibre–matrix interfaces10.1016/j.compscitech.2011.01.014 ↗
17. Effects of sintering temperature on mechanical properties of 3D mullite fiber (ALF FB3) reinforced mullite composites10.1016/j.ceramint.2013.05.030 ↗
18. Review of mullite synthesis routes by sol–gel method10.1007/s10971-010-2222-9 ↗
19. High-surface-area alumina–silica nanocatalysts prepared by a hybrid sol–gel route using a boehmite precursor10.1111/j.1551-2916.2010.03997.x ↗
20. Comparison of preparation routes of spinel catalyst for alkaline fuel cells10.1016/j.materresbull.2004.04.015 ↗
21. Molten salt corrosion of graphite as a possible way to make carbon nanostructures10.1016/j.carbon.2012.12.076 ↗
22. High-surface-area oxides obtained by an activated carbon route10.1021/cm0211857 ↗
23. Corrosion behaviour of carbon materials exposed to molten lithium chloride–potassium chloride salt10.1016/j.carbon.2013.10.040 ↗
24. Decomposition of mixed Mn and Co nitrates supported on carbon10.1016/j.tca.2004.09.005 ↗
25. Mechanical properties of oxide-fiber reinforced glass matrix composites with BN or SnO2 interfaces10.1016/j.msea.2005.11.001 ↗
26. Effects of the single layer CVD BN interface on mechanical properties of oxide–oxide composites fabricated by a sol–gel process10.1016/j.ceramint.2013.12.067 ↗
27. Thermal stability and kinetics of decomposition of ammonium nitrate in the presence of pyrite10.1016/j.jhazmat.2008.10.054 ↗
28. Review on thermal decomposition of ammonium nitrate10.1080/07370652.2011.573523 ↗
29. High-temperature erosion resistance and aerodynamic oxidation mechanism of multi-layer MoSi2–CrSi2–Si/SiC coated carbon/carbon composites in a wind tunnel at 1873K10.1016/j.carbon.2012.01.027 ↗
30. Kinetics of the oxidation of carbon black by NO2: influence of the presence of water and oxygen10.1016/S0008-6223(01)00103-8 ↗
31. Combustion characteristics of ammonium nitrate and carbon mixtures based on a thermal decomposition mechanism10.1002/prep.201100106 ↗
32. Boron nitride coatings by chemical vapor deposition from borazine10.1016/j.surfcoat.2011.01.032 ↗
33. Incorporate boron and nitrogen into graphene to make BCN hybrid nanosheets with enhanced microwave absorbing properties10.1016/j.carbon.2013.04.085 ↗
34. Raman spectroscopy of carbon materials: structural basis of observed spectra10.1021/cm00011a018 ↗
35. High-temperature behavior of silicon oxycarbide glasses in air environment10.1016/j.ceramint.2011.03.053 ↗
36. Raman spectrum of graphite10.1063/1.1674108 ↗
37. In situ growth of a carbon interphase between carbon fibres and a polycarbosilane-derived silicon carbide matrix10.1016/j.carbon.2011.02.056 ↗
38. AlPO4-coated mullite/alumina fiber reinforced reaction-bonded mullite composites10.1016/j.jeurceramsoc.2008.05.032 ↗