Insights into the role of grain refinement on high-temperature initial oxidation phase transformation and oxides evolution in high aluminium Fe-Mn-Al-C duplex lightweight steel
Source abstract
Abstract
Abstract Influence of grain size on internal oxidation behaviour at 1273 K in dry air of Fe-20Mn-8Al-0.45C (wt.%) has been investigated. The measured weight gains are in parabolic relation to oxidation time and parabolic rate constant degrades with the reduction of grain size. Grain size affects compositions of oxides in the initial oxidation process and diffusion abilities of cations. Fine-grained alloy becomes less permeable to oxygen than coarse-grained alloy. Grain refinement accelerates phase transformation and promotes the rapid formation of pure Al 2 O 3 layer, contributing to the slightly improved oxidation resistance. A brief schematic model is proposed to explain oxides evolution.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (65)
Show source-provided references
1. Novel ultra-high-strength (ferrite + austenite) duplex lightweight steels achieved by fine dislocation substructures (Taylor lattices) grain refinement, and partial recrystallization10.1016/j.actamat.2015.06.024 ↗
2. Novel ferrite–austenite duplex lightweight steel with 77% ductility by transformation induced plasticity and twinning induced plasticity mechanisms10.1016/j.actamat.2014.06.059 ↗
3. TEM study of the internal oxidation of an Fe-Mn-Al-C alloy after hot corrosion10.1023/A:1014834620707 ↗
4. NaCl-induced hot corrosion of Fe-Mn-Al-C alloys10.1016/S0254-0584(01)00515-6 ↗
5. The hot corrosion of Fe-Mn-Al-C alloy with NaCl/Na2SO4 coating mixtures at 750°C10.1023/A:1023022100300 ↗
6. Microstructures and mechanical properties of high-strength Fe-Mn-Al-C light-weight TRIPLEX steels10.1002/srin.200606440 ↗
7. Low-density low-carbon Fe-Al ferritic steels10.1016/j.scriptamat.2012.10.004 ↗
8. Tensile deformation of a duplex Fe-20Mn-9Al-0.6C steel having the reduced specific weight10.1016/j.msea.2011.03.045 ↗
9. Effect of annealing temperature on microstructural modification and tensile properties in 0.35C-3.5Mn-5.8Al lightweight steel10.1016/j.actamat.2013.04.038 ↗
10. Microstructure and tensile behavior of duplex low-density steel containing 5 mass% aluminum10.1016/j.scriptamat.2012.09.030 ↗
11. Tensile deformation of low density duplex Fe-Mn-Al-C steel10.1016/j.matdes.2015.03.043 ↗
12. Factors influencing the tensile behavior of a Fe-28Mn-9Al-0.8C steel10.1016/j.msea.2008.12.055 ↗
13. Mechanical properties of Fe-Al-M-C (M=Ti, V Nb, Ta) alloys with strengthening carbides and Laves phase10.1016/j.intermet.2004.05.010 ↗
14. Effect of aging on the microstructure and deformation behavior of austenite base lightweight Fe-28Mn-9Al-0.8C steel10.1016/j.scriptamat.2010.07.036 ↗
15. Stacking fault energy and plastic deformation of fully austenitic high manganese steels: effect of Al addition10.1016/j.msea.2010.02.058 ↗
16. Improved oxidation resistance of 15 wt.% Cr ferritic stainless steels containing 0. 08–2.45wt.% alat 1000°C in air10.1016/j.corsci.2015.08.007 ↗
17. High temperature oxidation of Fe-Al and Fe-Cr-Al alloys: the role of Cr as a chemically active element10.1016/j.corsci.2010.06.019 ↗
18. The effects of Cr and Al concentrations on the oxidation behavior of oxide dispersion strengthened ferritic alloys10.1016/j.corsci.2013.07.004 ↗
19. Criteria for the formation of protective Al2O3 scales on Fe-Al and Fe-Cr-Al alloys10.1016/j.corsci.2005.01.012 ↗
20. A study of the oxidation of FeCrAl alloy in pressurized water and high-temperature steam environment10.1016/j.corsci.2015.02.027 ↗
21. Influence of the alloy grain size on the oxidation behavior of PM2000 alloy10.1016/S0010-938X(01)00182-2 ↗
22. High-temperature oxidation of duplex stainless steels S32101 and S32304 in air and simulated industrial reheating atmosphere10.1016/j.corsci.2010.04.033 ↗
23. Self-repairing behavior of oxidation diffusion layer and phase transformation mechanism during tensile test of 19Cr duplex stainless steels with various Mn content10.1016/j.corsci.2014.10.046 ↗
24. Formation and growth morphology of nodules in the high-temperature oxidation of Fe-Mn-Al-C alloy10.1016/S0254-0584(02)00134-7 ↗
25. Tensile properties and twinning behavior of high manganese austenitic steel with fine-grained structure10.1016/j.scriptamat.2008.06.050 ↗
26. ARB (Accumulative roll-Bonding) and other new techniques to produce bulk ultrafine grained materials10.1002/adem.200310077 ↗
27. Strength and ductility of ultrafine grained aluminum and iron produced by ARB and annealing10.1016/S1359-6462(02)00282-8 ↗
28. Differences in oxides on large- and small-grained 304 stainless steel10.1007/BF02655116 ↗
29. Effect of grain refinement on the resistance of 304 stainless steel to breakaway oxidation in wet air10.1016/j.actamat.2005.07.019 ↗
30. Effect of alloy grain size and silicon content on the oxidation of austenitic Fe-Cr-Ni-Mn-Si alloys in pure O210.1007/BF00662967 ↗
31. Effect of grain size on the oxidation of Fe-13Cr-5Ni alloy at 973K in Ar-21 vol% O210.1016/j.corsci.2014.11.020 ↗
32. Influence of grain size on the oxidation behavior of NbCr2 alloys at 950–1200°C10.1016/j.corsci.2008.11.014 ↗
33. Synergistic influence of alloy grain size and Si content on the oxidation behavior of 9Cr-lMo steel10.1007/BF01046754 ↗
34. Effect of alloy grain size and silicon content on the oxidation of austenitic Fe-Cr-Ni-Mn-Si alloys in pure O210.1007/BF00662967 ↗
35. Oxidation kinetics of an Fe-31.8Mn-6.09Al-1.60Si-0.40C alloy at temperatures from 600 to 900°C10.1016/j.corsci.2003.10.015 ↗
36. Internal oxidation behavior of Fe-Mn-Al-C duplex steels with good combination of strength and ductility10.1016/j.corsci.2017.03.005 ↗
37. A model for heat conduction through the oxide layer of steel during hot rolling10.1016/S0924-0136(00)00569-0 ↗
38. Cracking and deformation of surface scale during hot rolling of steel10.1179/026708301225000761 ↗
39. The effect of scaling on interfacial friction in hot rolling of steels10.1016/S0924-0136(98)00392-6 ↗
40. Evolution of grain boundary character distributions in alloy 825 tubes during high temperature annealing: is grain boundary engineering achieved through recrystallization or grain growth?10.1016/j.matchar.2016.11.016 ↗
41. Glass coating on stainless steels for high temperature oxidation protection: mechanisms10.1016/j.corsci.2014.01.033 ↗
42. Diffusion-related kinetics in the oxidation-induced phase transformation of Fe-9Al-3Cr-31Mn alloys10.1149/1.2096755 ↗
43. A SERS investigation of the passive films formed on iron in mildly alkaline solutions of carbonate/bicarbonate and nitrate10.1016/0010-938X(94)00179-A ↗
44. The oxidation of iron-chromium-manganese alloys at 900°C10.1007/BF00938460 ↗
45. Fabrication of Cu2O/Fe-O heterojunction solar cells by electrodeposition10.1016/j.tsf.2015.11.034 ↗
46. Raman microspectroscopy of some iron oxides and oxyhydroxides10.1002/(SICI)1097-4555(199711)28:11<873::AID-JRS177>3.0.CO;2-B ↗
47. High-temperature oxidation studies of low-nickel austenitic stainless steel. Part I: isothermal oxidation10.1023/A:1010329310030 ↗
48. Byzantine wall paintings from Kastoria, northern Greece: spectroscopic study of pigments and efflorescing salts
49. Synthesis of nanocrystalline iron oxide ultrathin films by thermal decomposition of iron nitropruside: structural and optical properties10.1016/j.materresbull.2010.08.006 ↗
50. Peculiar porous α-Fe2O3, γ-Fe2O3 and Fe3O4 nanospheres: facile synthesis and electromagnetic properties10.1016/j.powtec.2014.09.045 ↗
51. Raman studies of corrosion films grown on Fe and Fe-6Mo in pitting conditions10.1016/0010-938X(91)90103-V ↗
52. Raman spectroscopy of thin corrosion films on iron at 100 to 150C in air10.5006/1.3583054 ↗
53. The air oxidation of an austenitic Fe-Mn-Cr stainless steel for fusion-reactor applications10.1007/BF00655899 ↗
54. Raman spectroscopy and XPS investigations of anodic corrosion films formed on Fe-Mo alloys in alkaline solutions10.1016/0010-938X(91)90073-X ↗
55. Lattice vibrations of materials for lithium rechargeable batteries V. Local structure of Li0.3MnO210.1016/S0921-5107(03)00079-5 ↗
56. A parametric study on the rapid synthesis of one dimensional (1D) α-MnO2 nanowires10.1016/j.mee.2014.05.028 ↗
57. Re-investigating the CO oxidation mechanism over unsupported MnO, Mn2O3 and MnO2 catalysts10.1016/j.cattod.2007.10.061 ↗
58. Kinetic and spectroscopic study of methane combustion over α-Mn2O3 nanocrystal catalysts10.1016/j.jcat.2007.11.010 ↗
59. One-step synthesis of crystalline Mn2O3 thin film by ultrasonic spray pyrolysis10.1016/j.tsf.2016.06.050 ↗
60. Controlled synthesis of Mn3O4 and MnCO3 in a solvothermal system10.1016/j.materresbull.2009.03.004 ↗
61. Nitrogen-induced selective high-temperature internal oxidation behavior in duplex stainless steels 19Cr-10Mn-0.3Ni-xN10.1016/j.corsci.2015.06.013 ↗
62. Tensile deformation of low density duplex Fe-Mn-Al-C steel10.1016/j.matdes.2015.03.043 ↗
63. THERMO-CALC & DICTRA: computational tools for material science10.1016/S0364-5916(02)00037-8 ↗
64. TCFE7-TCS, Steels/Fe-Alloys Database as supplied by Thermo-Calc Software AB, Stockholm, 2012.
65. SSUB4-SGTE Substances Database v4.1 as supplied by Thermo-Calc Software AB, Stockholm, 2006.