The effect of elastic tensile stress on inhibition behavior of N-lauroylsarcosine sodium for 304L stainless steel pitting corrosion
Source abstract
Abstract
N-lauroylsarcosine sodium is proved to be effective in inhibiting 304 L SS pitting corrosion. Under various elastic tensile stresses, the inhibition behavior of N-LSS on 304 L SS pitting corrosion is studied, and N-LSS increases significantly 304 L SS pitting potential by more than 400 mV. Under small elastic tensile stress (≤16.63 %σ 0.2), the adsorption of N-LSS can inhibit 304 L SS pitting corrosion by enhancing the protection of N-LSS film and specific adsorption effect of N-LSS. Under large elastic tensile stress (≥46.84 %σ 0.2), the decrease of N-LSS adsorption effect reduces the inhibition effect of N-LSS specific adsorption for 304 L SS pitting corrosion growth.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Corrosion Behavior and Inhibition · Hydrogen embrittlement and corrosion behaviors in metals · Concrete Corrosion and Durability
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (86)
Show source-provided references
1. Electronic properties and corrosion resistance of passive films on austenitic and duplex stainless steels10.1016/j.electacta.2018.04.058 ↗
2. Passivation mechanisms and pre-oxidation effects on model surfaces of FeCrNi austenitic stainless steel10.1016/j.corsci.2020.108483 ↗
3. Nanostructure and local properties of oxide layers grown on stainless steel in simulated pressurized water reactor environment10.1016/j.corsci.2014.03.030 ↗
4. Comparative study of the surface oxide films on lean duplex and corresponding single phase stainless steels by XPS and ToF-SIMS10.1016/j.corsci.2018.08.009 ↗
5. Effect of in site strain on passivated property of the 316L stainless steels10.1016/j.msec.2015.12.010 ↗
6. Simulation of metastable corrosion pit development under mechanical stress10.1016/j.electacta.2012.11.056 ↗
7. A study on localized corrosion behavior of 304 stainless steel in the presence of Allium sativum extract inhibitor using electrochemical noise analysis10.1016/j.matchemphys.2021.125158 ↗
8. Synergistic effect of SAMs of S-containing amino acids and surfactant on corrosion inhibition of 316L stainless steel in 0.5 M NaCl solution10.1016/j.molliq.2020.114322 ↗
9. Pitting corrosion inhibition of 304 stainless steel in NaCl solution by three newly synthesized carboxylic Schiff bases10.1016/j.corsci.2019.108130 ↗
10. Inhibitory effect of L-Threonine and L-Lysine and influence of surfactant on stainless steel corrosion in artificial body solution10.1016/j.molliq.2021.116939 ↗
11. Synergistic inhibition behavior of sodium tungstate and penicillin G as an eco-friendly inhibitor on pitting corrosion of 304 stainless steel in NaCl solution using Design of Experiment10.1016/j.molliq.2019.111330 ↗
12. A review of surfactants as corrosion inhibitors and associated modeling10.1016/j.pmatsci.2017.07.006 ↗
13. Pitting inhibition of stainless steel by surfactants: an electrochemical and surface chemical approach10.1016/S0021-9797(03)00025-0 ↗
14. The adsorption and inhibition effect of calcium lignosulfonate on Q235 carbon steel in simulated concrete pore solution10.1016/j.apsusc.2016.04.013 ↗
15. Layer-by-layer assembly of fluorine-free polyelectrolyte–surfactant complexes for the fabrication of self-healing superhydrophobic films10.1021/acs.langmuir.6b02607 ↗
16. Synthesis of gemini cationic surfactants-based pyridine Schiff base for steel corrosion and sulfate reducing bacteria mitigation10.1016/j.molliq.2022.120890 ↗
17. Coupling of surface energy with electric potential makes superhydrophobic surfaces corrosion-resistant10.1039/C5CP04462F ↗
18. Effect of molecular-scale surface energy alteration of aluminium on its corrosion resistance behaviour10.1016/j.colsurfa.2018.10.046 ↗
19. Detection of corrosion inhibition by dithiane self-assembled monolayers (SAMs) on copper10.1016/j.jtice.2022.104610 ↗
20. A substrate-independent isocyanate-modified polydimethylsiloxane coating harvesting mechanical durability, self-healing ability and low surface energy with anti-corrosion/biofouling potential10.1016/j.apsusc.2021.152186 ↗
21. Inhibitive effect of sodium (E)-4-(4-nitrobenzylideneamino)benzoate on the corrosion of some metals in sodium chloride solution10.1016/j.apsusc.2018.04.073 ↗
22. Inhibition effect and mechanism of sodium oleate on passivation and pitting corrosion of steel in simulated concrete pore solution10.1016/j.conbuildmat.2018.01.170 ↗
23. Corrosion performance of reinforcing steel in concrete under simultaneous flexural load and chlorides attack10.1016/j.conbuildmat.2017.05.092 ↗
24. Pit initiation on stainless steels in 1 M NaCl with and without mechanical stress10.1149/1.1360204 ↗
25. Effect of stress and strain on corrosion resistance of duplex stainless steel10.1016/j.ijpvp.2013.04.025 ↗
26. Synergistic effect of sulfate-reducing bacteria and elastic stress on corrosion of X80 steel in soil solution10.1016/j.corsci.2014.01.017 ↗
27. Insight into electrochemical passivation behavior and surface chemistry of 2205 duplex stainless steel: effect of tensile elastic stress10.1016/j.corsci.2021.109903 ↗
28. Influence of an elastic stress on the conductivity of passive films10.1016/S0921-5093(00)01843-8 ↗
29. Effect of tensile stress on pitting resistance of 2205 duplex stainless steel
30. Study on pitting corrosion behavior and semi in-situ pitting corrosion growth model of 304 L SS with elastic stress in NaCl corrosion environment10.1016/j.corsci.2022.110862 ↗
31. Acoustic emission during pitting corrosion of 304 stainless steel10.1016/j.corsci.2011.01.030 ↗
32. Influence of carbon on the corrosion behaviour of interstitial equiatomic CoCrFeMnNi high-entropy alloys in a chlorinated concrete solution10.1016/j.corsci.2019.108287 ↗
33. Passivity of 316L stainless steel in borate buffer solution studied by Mott–Schottky analysis, atomic absorption spectrometry and X-ray photoelectron spectroscopy10.1016/j.corsci.2010.07.013 ↗
34. Automated ex-situ detection of pitting corrosion and its effect on the mechanical integrity of rare earth magnesium alloy - WE43
35. Statistical analysis of the pitting corrosion induced by potentiostatic pulse tests of wrought and SLM 316L stainless steels10.1016/j.corsci.2021.110036 ↗
36. Potential of zero free charge of Pd overlayers on Pt(111)10.1016/j.electacta.2005.07.036 ↗
37. High corrosion and wear resistance of Al-based amorphous metallic coating synthesized by HVAF spraying10.1016/j.jallcom.2017.11.274 ↗
38. Influence of metal surface preparation on its surface profile, contact angle, surface energy and adhesion with glass fibre prepreg10.1016/j.ijadhadh.2014.02.006 ↗
39. Using contact angle measurement technique for determination of the surface free energy of B-SBA-15-x materials10.1016/j.ijadhadh.2021.103024 ↗
40. Comparison of a bio_based corrosion inhibitor versus benzotriazole on corroded copper surfaces10.1016/j.corsci.2018.08.020 ↗
41. Inhibition of Q235 carbon steel by calcium lignosulfonate and sodium molybdate in carbonated concrete pore solution
42. Corrosion inhibition performance of 2,5-bis(4-dimethylaminophenyl)-1,3,4-oxadiazole for carbon steel in HCl solution: gravimetric, electrochemical and XPS studies10.1016/j.apsusc.2016.07.115 ↗
43. Study of stainless steels corrosion in a strong acid mixture. Part 1: cyclic potentiodynamic polarization curves examined by means of an analytical method10.1016/j.corsci.2017.10.012 ↗
44. Effects of hydrogen and tensile stress on the breakdown of passive films on type 304 stainless steel10.1016/S0013-4686(00)00661-7 ↗
45. The influence of hydrogen and tensile stress on passivity of type 304 stainless steel10.1149/1.1589760 ↗
46. The metastable pitting potential and its relation to the pitting potential for four materials in chloride solutions10.1016/j.corsci.2013.11.015 ↗
47. High temperature solution-nitriding and low-temperature nitriding of AISI 316: effect on pitting potential and crevice corrosion performance10.1016/j.apsusc.2017.06.094 ↗
48. Effect of pitting nucleation on critical pitting temperature of 316L stainless steel by nitric acid passivation10.1016/j.corsci.2014.11.018 ↗
49. Metastable pitting corrosion of 304 stainless steel in 3.5 % NaCl solution10.1016/j.corsci.2014.04.033 ↗
50. In-situ monitoring of pitting corrosion on vertically positioned 304 stainless steel by analyzing acoustic-emission energy parameter10.1016/j.corsci.2015.12.010 ↗
51. Morphological estimation of pitting corrosion on vertically positioned 304 stainless steel using acoustic-emission duration parameter10.1016/j.corsci.2018.12.031 ↗
52. The effect of dichromate ion on the pitting corrosion of AISI 316 stainless steel Part II: pit initiation and transition to stability10.1016/j.corsci.2015.02.025 ↗
53. Phased acoustic emission sensor array for localizing radial and axial positions of defects in hollow structures10.1016/j.measurement.2019.107223 ↗
54. Passivity of Sanicro28 (UNS N-08028) stainless steel in polluted phosphoric acid at different temperatures studied by electrochemical impedance spectroscopy and Mott–Schottky analysis10.1016/j.corsci.2014.04.056 ↗
55. Semiconducting and passive film properties of nitrogen-containing type 316LN stainless steels10.1016/j.corsci.2006.05.041 ↗
56. Unmasking chloride attack on the passive film of metals10.1038/s41467-018-04942-x ↗
57. Effect of Residual Stress on the Corrosion Behavior of Austenitic Stainless Steel10.4236/aces.2015.51007 ↗
58. Effect of pH on the electrochemical behaviour and passive film composition of 316L stainless steel10.1007/s40195-018-0794-5 ↗
59. Electrochemical behavior of additively manufactured 316L stainless steel in H2SO4 solution containing methionine as an amino acid10.1016/j.colsurfa.2021.127120 ↗
60. Correlating the five parameter grain boundary character distribution and the intergranular corrosion behaviour of a stainless steel using 3D orientation microscopy based on mechanical polishing serial sectioning10.1016/j.actamat.2018.06.044 ↗
61. Molecular dynamic simulation and experimental investigation on the synergistic mechanism and synergistic effect of oleic acid imidazoline and l-cysteine corrosion inhibitors10.1016/j.corsci.2021.109414 ↗
62. Corrosion behavior of bulk (Zr58Nb3Cu16Ni13Al10)100-xYx (x = 0, 0.5, 2.5 at %) metallic glasses in sulfuric acid10.1016/j.corsci.2019.01.016 ↗
63. Adsorption and corrosion inhibition of phytic acid calcium on the copper surface in 3wt% NaCl solution10.1016/j.corsci.2014.02.001 ↗
64. An electrochemical impedance spectroscopy study of the corrosion behaviour of PVD coated steels in 0.5 N NaCl aqueous solution: part II.: EIS interpretation of corrosion behaviour10.1016/S0010-938X(02)00214-7 ↗
65. Electrochemical and surface analysis studies on corrosion inhibition of Q235 steel by imidazoline derivative against CO2 corrosion10.1016/j.corsci.2010.09.042 ↗
66. Inhibition behavior of an imidazoline inhibitor for carbon steel in a supercritical CO2/H2O system10.1149/2.0151712jes ↗
67. Effect of extremely aggressive environment on the nature of corrosion scales of HP-13Cr stainless steel10.1016/j.apsusc.2018.10.237 ↗
68. Effect of dissolved oxygen on electrochemical corrosion behavior of 2205 duplex stainless steel in hot concentrated seawater10.1016/j.jmst.2020.06.030 ↗
69. J. Yang, C.D. Yim, B.S. You, Effects of Sn in α-Mg Matrix on Properties of Surface Films of Mg-xSn (x = 0, 2, 5 wt%) Alloys, 67 (2016) 531-541.https://doi.org/10.1002/maco.201508585.10.1002/maco.201508585 ↗
70. Pitting Corrosion Behaviors of 2205 Duplex Stainless Steel
71. Thermodynamics of the mechanico-chemical effect
72. Corrosion in cracks and electrochemical protection against stress corrosion
73. The role of surfactant adsorption in the improved dewatering of fine coal10.1016/S0016-2361(98)00169-0 ↗
74. Adsorption and Inhibition Action of Dodecyl Dimethyl Benzyl Ammonium Chloride on Cold-rolled Steel in Trichloroacetic Acid
75. Iron Derivatives from Casein Hydrolysates as a Potential Source in the Treatment of Iron Deficiency10.1021/jf0111312 ↗
76. Separation of iron-binding protein from whey through enzymatic hydrolysis10.1016/j.idairyj.2006.09.001 ↗
77. Chicken foot broth byproduct: a new source for highly effective peptide-calcium chelate10.1016/j.foodchem.2020.128713 ↗
78. Particulate nanocomposite from oyster (Crassostrea rivularis) hydrolysates via zinc chelation improves zinc solubility and peptide activity10.1016/j.foodchem.2018.03.030 ↗
79. A specific peptide with calcium chelating capacity isolated from whey protein hydrolysate10.1016/j.jff.2014.05.013 ↗
80. Preparation, characterization and in vitro stability of iron-chelating peptides from mung beans10.1016/j.foodchem.2021.129101 ↗
81. Degradability of Iron(III)-aminopolycarboxylate complexes in alkaline media: statistical design and X-ray photoelectron spectroscopy studies10.1021/ie049636f ↗
82. Interfacial solid-phase chemical modification with mannich reaction and fe(iii) chelation for designing lignin-based spherical nanoparticle adsorbents for highly efficient removal of low concentration phosphate from water10.1021/acssuschemeng.7b00674 ↗
83. Effect of iron ions as assistant depressant of citric acid on the flotation separation of scheelite from calcite10.1016/j.ces.2021.116720 ↗
84. Fe(III)-Chelated Polydopamine Nanoparticles for Synergistic Tumor Therapies of Enhanced Photothermal Ablation and Antitumor Immune Activation10.1021/acsami.1c24066 ↗
85. XPS study of finely dispersed iron powders modified by radiation-grafted acrylamide10.1002/1096-9918(200008)29:8<519::AID-SIA896>3.0.CO;2-8 ↗
86. Analysis of problematic complexing behavior of Ferric chloride with n,n-dimethylformamide using combined techniques of FT-IR, XPS, and TGA/DTG10.1021/ic011306p ↗