Influence of cathodic polarization on stress corrosion cracking susceptibility of 35CrMo steel for high strength bolt in simulated deep-sea environment
Source abstract
Abstract
The effect of cathodic polarization on stress corrosion cracking (SCC) of 35CrMo steel for high strength bolt in the simulated deep-sea environment has been studied. The results show that 35CrMo steel has a higher SCC sensitivity at open circuit potential in the simulated deep-sea environment than that in the shallow seawater. With potential negatively shifted to −750 mV, 35CrMo steel presents the lowest SCC sensitivity. And the SCC susceptibility is increased significantly with the further negative shift of potential because of the intensive hydrogen evolution. When the potential is below −950 mV, hydrogen embrittlement with hydrogen-enhanced-plasticity mediated decohesion should be the dominant SCC micro-mechanism.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Corrosion Behavior and Inhibition · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (99)
Show source-provided references
1. Effect of hydrogen charging on SCC of 2205 duplex stainless steel with varying microstructures in simulated deep-sea environment10.1016/j.corsci.2021.110026 ↗
2. Long-term field exposure corrosion behavior investigation of 316L stainless steel in the deep sea environment10.1016/j.oceaneng.2019.106405 ↗
3. Pitting corrosion of 2Cr13 stainless steel in deep-sea environment10.1016/j.jmst.2020.04.036 ↗
4. Effects of hydrostatic pressure and pH on the corrosion behavior of 2205 duplex stainless steel10.1016/j.jelechem.2021.115134 ↗
5. Effect of the calcareous deposits on the stress corrosion cracking behavior of 10Ni5CrMoV high strength steel in deep-sea environment10.20964/2021.05.63 ↗
6. Corrosion resistance of composite coating used for fastener protection10.1108/ACMM-03-2019-2095 ↗
7. Sacrificial Zn-Ni coatings by electroplating and hydrogen embrittlement of high-strength steels10.1515/corrrev-2021-0038 ↗
8. Hydrogen embrittlement of high-strength marine steel as a weld joint in artificial seawater under cathodic polarization10.1016/j.engfailanal.2022.106044 ↗
9. Effect of cathodic polarisation on stress corrosion cracking behaviour of a Ni(Fe, Al)-maraging steel in artificial seawater10.1016/j.corsci.2020.109176 ↗
10. Effect of cathodic potential on stress corrosion cracking behavior of different heat-affected zone microstructures of E690 steel in artificial seawater10.1016/j.jmst.2019.08.029 ↗
11. The effect of hydrogen on stress corrosion behavior of X65 steel welded joint in simulated deep sea environment10.1016/j.oceaneng.2016.01.020 ↗
12. Hydrogen-assisted cracking in 2205 duplex stainless steel: initiation, propagation and interaction with deformation-induced martensite10.1016/j.msea.2020.140079 ↗
13. Corrosion of ferrous alloys in deep sea environments10.1179/000705902225006633 ↗
14. Corrosion behavior of Q235 steel exposed in deepwater of South China Sea10.1007/s11665-018-3553-x ↗
15. Corrosion form transition of mooring chain in simulated deep-sea environments: remarkable roles of dissolved oxygen and hydrostatic pressure10.1016/j.jmst.2023.04.013 ↗
16. Effect of hydrostatic pressure on the corrosion behavior of a low alloy steel10.1149/2.040303jes ↗
17. Hydrostatic pressure effects on corrosion behavior of X70 pipeline steel in a simulated deep-sea environment10.1016/j.jelechem.2018.05.010 ↗
18. Modeling the corrosion behavior of Ni-Cr-Mo-V high strength steel in the simulated deep sea environments using design of experiment and artificial neural network10.1016/j.jmst.2018.06.017 ↗
19. Comparative study on the stress corrosion cracking of X70 pipeline steel in simulated shallow and deep sea environments10.1016/j.msea.2016.12.118 ↗
20. Hydrostatic pressure effects on stress corrosion cracking of X70 pipeline steel in a simulated deep-sea environment10.1016/j.ijhydene.2017.09.061 ↗
21. A primary study of the effect of hydrostatic pressure on stress corrosion cracking of Ti-6Al-4V alloy in 3.5% NaCl solution10.1016/j.corsci.2019.108402 ↗
22. Hydrostatic pressure effects on hydrogen entry into A514 steel with cathodic deposits10.1016/j.electacta.2018.07.049 ↗
23. Stress corrosion cracking of 2205 duplex stainless steel with simulated welding microstructures in simulated sea environment at different depths10.1007/s11665-020-05052-w ↗
24. The role of hydrostatic pressure on the metal corrosion in simulated deep-sea environments - a review10.1016/j.jmst.2021.10.014 ↗
25. Simulated service test for hydrogen embrittlement of cathodically protected subsea bolting materials10.1179/bcj.1995.30.2.154 ↗
26. Chapter 2 - External offshore subsea corrosion
27. Effect of cathodic polarization on stress corrosion cracking susceptibility of 35CrMo steel for Class 12.9 fasteners in seawater10.1016/j.jmrt.2023.05.158 ↗
28. ISO 5668:2023 · 2023
29. Investigation of stress corrosion cracking behavior and mechanism analysis of a 1900 MPa-grade ultra-high-strength stainless steel10.1007/s42243-021-00710-2 ↗
30. Comparative study on the stress corrosion cracking of a new Ni-advanced high strength steel prepared by TMCP, direct quenching, and quenching & tempering10.1016/j.msea.2021.141854 ↗
31. Characteristics of hydrogen embrittlement in high-pH stress corrosion cracking of X100 pipeline steel in carbonate/bicarbonate solution10.1016/j.conbuildmat.2020.120124 ↗
32. Effect of cathodic potentials on the SCC behavior of E690 steel in simulated seawater10.1016/j.msea.2015.05.109 ↗
33. Predictive approaches to stresss corrosion cracking failure10.1016/0010-938X(80)90128-6 ↗
34. An experimental study on stress corrosion behavior of A131/A and A131/AH32 low carbon steels in simulated seawater10.1016/j.oceaneng.2019.106204 ↗
35. Early corrosion behavior of 35CrMo steel for high-strength bolt in simulated shallow and deep sea environments10.1016/j.jmrt.2023.12.080 ↗
36. Degradation mechanism of long service life Ti/IrO2-Ta2O5 oxide anodes in sulphuric acid10.1016/S0010-938X(01)00165-2 ↗
37. Effect of the calcareous deposits on the cathodic protection potential of 10Ni5CrMoV high-strength steel in a deep-sea environment by using the response surface methodology10.1002/maco.202011886 ↗
38. The influence of calcareous deposits on hydrogen uptake and embrittlement of API 5CT P110 steel10.1016/j.corsci.2017.02.007 ↗
39. Effect of calcareous deposits on hydrogen permeation in X80 steel under cathodic protection10.1016/j.matchemphys.2017.12.015 ↗
40. Deep water cathodic protection: part 2-field deployment results10.5006/1.3277601 ↗
41. A study of calcareous deposits on cathodically protected mild steel in artificial seawater10.3390/met5010439 ↗
42. Surface and electrochemical corrosion analysis of niobium oxide film formed in various wet media10.1016/j.apsadv.2021.100079 ↗
43. Atomic layer deposition of vanadium pentoxide on carbon electrode for enhanced capacitance performance in capacitive deionization, Applied
44. Effect of temperature on corrosion behavior of X65 steel in simulated deep sea environment10.20964/2019.01.29 ↗
45. Effect of dissolved oxygen on pitting corrosion behavior of low-alloy steel under hydrostatic pressure10.20964/2019.05.49 ↗
46. Effect of cathodic potentials on hydrogen embrittlement of 1000 MPa grade high strength steel in simulated deep-sea environment
47. Stress corrosion cracking behavior of X70 pipe steel in an acidic soil environment10.1016/j.corsci.2008.05.011 ↗
48. Effects of cathodic protection on duplex stainless steels in seawater10.5006/1.3280465 ↗
49. ISO 12473:2017 · 2017
50. Challenges and solutions of cathodic protection for marine ships10.1016/j.corcom.2021.08.003 ↗
51. Hydrogen embrittlement of an automotive 1700 MPa martensitic advanced high-strength steel10.1016/j.corsci.2020.108726 ↗
52. Investigation on hydrogen embrittlement susceptibility in martensitic steels with 1000 MPa yield strength10.1016/j.jmrt.2021.11.130 ↗
53. Effects of hydrogen pressure and prior austenite grain size on the hydrogen embrittlement characteristics of a press-hardened martensitic steel10.1016/j.ijhydene.2021.05.005 ↗
54. Evaluation of susceptibility of high strength steels to delayed fracture by using cyclic corrosion test and slow strain rate test10.1016/j.corsci.2010.02.005 ↗
55. Investigation of the calcareous deposits formation controlled by interfacial pH and its effect on the hydrogen entry into AISI 4135 steel in seawater10.1016/j.ijhydene.2020.11.040 ↗
56. Microstructural and crystallographic features of hydrogenrelated crack propagation in low carbon martensitic steel10.2355/isijinternational.52.208 ↗
57. Combined effect of hydrogen embrittlement and corrosion on the cracking behaviour of C110 low alloy steel in O2-contaminated H2S environment10.1016/j.corsci.2021.109926 ↗
58. Effect of dissolved oxygen content on stress corrosion cracking of a cold worked 316L stainless steel in simulated pressurized water reactor primary water environment10.1016/j.jnucmat.2013.11.027 ↗
59. New perspectives on the grain boundary misorientation angle dependent intergranular corrosion of polycrystalline nickel-based 625 alloy10.1016/j.corsci.2020.108718 ↗
60. Texture and grain boundary study in high strength Fe-18Ni-Co steel related to hydrogen embrittlement10.1016/j.matdes.2015.11.093 ↗
61. A closer inspection of a grain boundary immune to intergranular corrosion in a sensitised Al-Mg alloy10.1016/j.corsci.2018.01.009 ↗
62. A new understanding of intergranular stress corrosion cracking resistance of pipeline steel through grain boundary character and crystallographic texture studies10.1016/j.corsci.2008.10.006 ↗
63. About quantitative EBSD analysis of deformation and recovery substructures in pure tantalum10.1088/1757-899X/89/1/012038 ↗
64. Influence of plastic deformation heterogeneity on development of geometrically necessary dislocation density in dual phase steel10.1016/j.msea.2016.05.022 ↗
65. Correlations between two EBSD-based metrics Kernel average misorientation and image quality on indicating dislocations of near-failure low alloy steels induced by tensile and cyclic deformations
66. Hydrogen-enhanced-plasticity mediated decohesion for hydrogen-induced intergranular and “quasi-cleavage” fracture of lath martensitic steels10.1016/j.jmps.2017.12.016 ↗
67. Hydrogen damage of steels: a case study and hydrogen embrittlement model10.1016/j.engfailanal.2015.05.017 ↗
68. The synergistic action and interplay of hydrogen embrittlement mechanisms in steels and iron: localized plasticity and decohesion10.1016/j.engfracmech.2019.106528 ↗
69. Effect of Nb on the hydrogen-induced cracking of high-strength low-alloy steel10.1016/j.corsci.2018.04.041 ↗
70. Fatigue crack initiation in as forged Ti-6Al-4V bars with macrozones present10.1016/j.ijfatigue.2015.05.020 ↗
71. Ratchetting-fatigue behavior of a 42CrMo steel under near-yield mean stress10.1016/j.ijmecsci.2023.108166 ↗
72. Mechanism of dislocation evolution during plastic deformation of nitrogen-doped CoCrFeMnNi high-entropy alloy10.1016/j.msea.2021.141235 ↗
73. Relationship between localized strain and irradiation assisted stress corrosion cracking in an austenitic alloy10.1016/j.msea.2011.01.073 ↗
74. A model for the normal stress dependence of intergranular cracking of irradiated 316L stainless steel in supercritical water10.1016/j.jnucmat.2010.11.012 ↗
75. Adverse effects of Ni on the mechanical and corrosion-induced hydrogen embrittlement properties of ultra-strong giga steel used for automotive applications10.1016/j.matdes.2020.108877 ↗
76. Evolution of dissolution processes at the interface of carbon steel corroding in a CO2 environment studied by EIS10.1016/j.corsci.2009.10.007 ↗
77. Effects of two-step austenitizing processes on hydrogen evolution, permeation, and cracking behaviors of ultra-high-strength martensitic steel10.1016/j.msea.2022.144214 ↗
78. Pitting corrosion resistance of martensite of AISI 1045 steel and the beneficial role of interstitial carbon10.1149/2.0541714jes ↗
79. Combined effect of cathodic potential and sulfur species on calcareous deposition, hydrogen permeation, and hydrogen embrittlement of a low carbon bainite steel in artificial seawater10.1016/j.corsci.2019.07.013 ↗
80. Corrosion evolution and stress corrosion cracking of E690 steel for marine construction in artificial seawater under potentiostatic anodic polarization10.1016/j.conbuildmat.2019.117763 ↗
81. Stainless steel pitting and early-stage stress corrosion cracking under ultra-low elastic load10.1016/j.corsci.2013.08.028 ↗
82. Stress corrosion cracking under low stress: Continuous or discontinuous cracks?10.1016/j.corsci.2013.11.057 ↗
83. Effect of hydrogen on the fracture behavior of high strength steel during slow strain rate test10.1016/j.corsci.2007.03.038 ↗
84. Hydrostatic pressure effects on hydrogen permeation in A514 steel during galvanostatic hydrogen charging10.1016/j.corsci.2016.07.001 ↗
85. Effect of cathodic potential on stress corrosion cracking behavior of 21Cr2NiMo steel in simulated seawater10.1007/s12613-020-2199-5 ↗
86. Hydrogen in metals10.1063/1.2994814 ↗
87. The effect of hydrogen on the yield and flow stress of an austenitic stainless steel10.1007/BF02669643 ↗
88. Effects of different cooling rates on the microstructure, crystallographic features, and hydrogen induced cracking of API X80 pipeline steel10.1016/j.jmrt.2021.07.060 ↗
89. Comments on “A unified model of environment-assisted cracking10.1016/j.scriptamat.2009.02.031 ↗
90. Hydrogen embrittlement phenomena and mechanisms10.1515/corrrev-2012-0502 ↗
91. Investigations into the delayed fracture susceptibility of 34CrNiMo6 steel, and the opportunities for its application in ultra-high-strength bolts and fasteners10.1016/j.msea.2013.10.019 ↗
92. Hydrogen-induced intergranular stress corrosion cracking (HI-IGSCC) of 0.35C-3.5Ni-1.5Cr-0.5Mo steel fastener10.1016/j.engfailanal.2009.10.007 ↗
93. Influence of tempering time on the fracture toughness of hydrogen pre-charged 42CrMo4 steel10.1016/j.tafmec.2021.103197 ↗
94. Hydrogen-induced delayed fracture behaviour of V+Nb-microalloyed high-strength bolt steel with internal and environmental hydrogen10.1016/j.corsci.2022.110710 ↗
95. Effect of environmental and internal hydrogen on the hydrogen assisted cracking behavior of TRIP-assisted steel10.1016/j.msea.2018.10.072 ↗
96. intergranular fracture of steels10.1016/S0013-7944(00)00124-7 ↗
97. Interpretation of hydrogen-induced fracture surface morphologies for lath martensitic steel10.1016/j.mspro.2014.06.274 ↗
98. Cohesive zone modeling of hydrogen-induced delayed intergranular fracture in high strength steels10.1016/j.rinp.2018.10.001 ↗
99. Stress-induced hydrogen redistribution and corresponding fracture behavior of Q960E steel at different hydrogen content10.1016/j.msea.2020.138963 ↗