journal article·2019-05

Fine tuning the mechanical properties of dual phase steel via thermomechanical processing of cold rolling and intercritical annealing

Sheida Nikkhah, Hamed Mirzadeh, Mehran Zamani

Publisher page

Abstract

Abstract The simultaneous effects of cold rolling reduction and intercritical annealing time on the microstructure and tensile properties of St12 steel were studied. It was revealed that by increasing the rolling reduction, the ferrite grain size of the dual phase (DP) microstructure is refined and a chain-like morphology of martensite develops, which results in improvement of work-hardening capacity and the tensile properties. Such a microstructure can be obtained via applying an optimum holding time at the intercritical annealing temperature. Beyond that optimum, grain coarsening occurs with the resulting deterioration of tensile properties. It was also shown that by consideration of quenched sheet or by applying low reductions in thickness, secondary recrystallization or abnormal grain growth (AGG) takes place during intercritical annealing, which is characterized by small grains and some large ferrite grains containing martensite islands. This study clarified that applying high reduction in thickness for grain refinement and also controlling the holding time in the two-phase austenite-ferrite region are the essential prerequisites to achieve the desired tensile strength, ductility, and toughness.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. Examination of phase transformation kinetics during step quenching of dual phase steels10.1016/j.matchemphys.2016.12.002 ↗
2. Alloying effects on microstructure formation of dual phase steels10.1016/j.actamat.2015.05.005 ↗
3. Superior strength and ductility of 316L stainless steel with heterogeneous lamella structure10.1007/s10853-018-2322-4 ↗
4. Deformation mechanisms of 304L stainless steel with heterogeneous lamella structure10.1016/j.msea.2018.11.047 ↗
5. Microstructure based prediction of strain hardening behavior of dual phase steels10.1016/j.matdes.2012.05.010 ↗
6. Development of a new dual phase steel with laminated microstructural morphology10.1016/j.matchemphys.2017.01.052 ↗
7. Effect of intercritical annealing on mechanical properties and work-hardening response of high formability dual phase steel10.1002/srin.201700412 ↗
8. Effect of microstructural refinement and intercritical annealing time on mechanical properties of high-formability dual phase steel10.1016/j.msea.2018.08.088 ↗
9. F. Najafkhani, H. Mirzadeh, M. Zamani, Effect of intercritical annealing conditions on grain growth kinetics of dual phase steel, Met. Mater. Int., 10.1007/s12540-019-00241-2.
10. Enhancement of mechanical properties of low carbon dual phase steel via natural aging10.1016/j.msea.2018.07.105 ↗
11. Modification of rule of mixtures for estimation of the mechanical properties of dual-phase steels10.1007/s11665-017-2687-6 ↗
12. Effects of martensite particle size and spatial distribution on work hardening behaviour of fine-grained dual-phase steel10.1080/00084433.2017.1403105 ↗
13. Enhancement of work-hardening behavior of dual phase steel by heat treatment10.1002/mawe.201700122 ↗
14. Dual phase structure formed by partial reversion of cold-deformed martensite10.1016/j.msea.2012.06.001 ↗
15. Effect of grain refinement to 1 μm on strength and toughness of dual-phase steels10.1016/j.msea.2010.08.062 ↗
16. Effect of pre-intercritical annealing treatments on the microstructure and mechanical properties of 0.33% carbon dual-phase steel10.1007/s11665-015-1750-4 ↗
17. Influence of martensite morphology on the work-hardening behavior of high strength ferrite–martensite dual-phase steel10.1007/s10853-009-3392-0 ↗
18. Effect of holding time at an intercritical temperature on the microstructure and tensile properties of a ferrite-martensite dual phase steel10.1016/j.msea.2018.07.029 ↗
19. Tailoring the microstructure and mechanical properties of dual phase steel based on the initial microstructure10.1002/srin.201600385 ↗
20. Unraveling the initial microstructure effects on mechanical properties and work-hardening capacity of dual phase steel10.1007/s11661-017-4246-z ↗
21. Formation of ultrafine grained dual phase steels through rapid heating10.2355/isijinternational.51.958 ↗
22. Fabrication of ultrafine grained ferrite/martensite dual phase steel by severe plastic deformation10.2355/isijinternational.45.750 ↗
23. Enhanced mechanical properties of dual phase steel by repetitive intercritical annealing10.1080/00084433.2017.1361223 ↗
24. Microstructure, texture and mechanical properties in a low carbon steel after ultrafast heating10.1016/j.msea.2016.06.056 ↗
25. Influence of martensite composition and content on the properties of dual phase steels10.1007/BF02659924 ↗
26. Tyagi · Mater. Sci. Technol. · 2004 · 20 · 64510.1179/026708304225012062 ↗
27. Correlation of mechanical properties with fracture surface features in a newly developed dual-phase steel10.1007/s11665-015-1412-6 ↗
28. Hot deformation behavior, dynamic recrystallization, and physically-based constitutive modeling of plain carbon steels10.1016/j.msea.2015.03.104 ↗
29. Enhanced ductility of a fine-grained Mg–Gd–Al–Zn magnesium alloy by hot extrusion10.1002/adem.201701171 ↗
30. Hot deformation behavior of a medium carbon microalloyed steel10.1016/j.msea.2011.01.098 ↗
31. Mechanical properties of a hot deformed Al-Mg2Si in-situ composite10.1016/j.msea.2018.04.064 ↗
32. Toward unraveling the effects of intermetallic compounds on the microstructure and mechanical properties of Mg–Gd–Al–Zn magnesium alloys in the as-cast, homogenized, and extruded conditions10.1016/j.msea.2016.10.084 ↗
33. Dieter · 1988
34. Fine-grained dual phase steel via intercritical annealing of cold-rolled martensite10.1016/j.vacuum.2018.06.003 ↗
35. Krauss · 2015
36. Refinement of banded structure via thermal cycling and its effects on mechanical properties of dual phase steel10.1002/srin.201700531 ↗
37. Effect of martensite morphology on tensile deformation of dual-phase steel10.1007/s11665-011-9934-z ↗
38. Humphreys · 2012
39. Elucidating the effect of intermetallic compounds on the behavior of Mg-Gd-Al-Zn magnesium alloys at elevated temperatures10.1557/jmr.2017.415 ↗
40. Advanced cold rolled steels for automotive applications