Study on the corrosion behavior of cold sprayed aluminum-based coatings on Mg-based alloy in chloride containing solution: Effect of N2 processing gas temperature
Source abstract
Abstract
Cold sprayed (CS) commercially pure Al-based coatings (processed at various propellent N 2 gas temperatures) were applied on Mg-based alloys. The porosity percentage of the CS coatings decreased, and the flattening ratio increased as the N 2 processing gas temperature reduced due to the effect of the in-situ tamping densification. This also led to the obvious reduction of wear rate of the CS Al-based coatings. In the present research, among the Al coated Mg alloys having higher general corrosion resistance (i.e., higher |Z| f=0.01 Hz and polarization resistance at the corrosion potential (R pol )), a decrease in dislocation density and microstrain was postulated to lead to the improvement of overall pitting behavior of the CS Al-based coating (processed at the lowest N 2 propellent gas temperature) after 12 days immersion in 3.5 wt% NaCl solution.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Magnesium Alloys: Properties and Applications · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (100+)
Show source-provided references
1. Protective coatings on magnesium and its alloys — a critical review10.1016/S0925-8388(01)01899-0 ↗
2. Electrochemical corrosion behavior of Mg–5Al–0.4Mn–xNd in NaCl solution10.1016/j.corsci.2009.03.019 ↗
3. Effect of grain size and twins on corrosion behavior of AZ31B magnesium alloy10.1016/j.corsci.2009.10.018 ↗
4. Effects of organic acid pickling on the corrosion resistance of magnesium alloy AZ31 sheet10.1016/j.corsci.2010.03.002 ↗
5. Development of a thiophene derivative modified LDH coating for Mg alloy corrosion protection10.1016/j.electacta.2019.135186 ↗
6. The dual role of Mg2+in the conversion bath during the treatment of magnesium alloys: the completing effect between heterogeneous nucleation and crystal growth10.1016/j.electacta.2021.138568 ↗
7. PTMS/OH-MWCNT sol-gel nanocomposite for corrosion protection of magnesium alloy10.1016/j.surfcoat.2017.12.044 ↗
8. Improved corrosion resistance of AZ31 Mg alloy coated with MXenes/MgAl-LDHs composite layer modified with yttrium10.1016/j.electacta.2021.137913 ↗
9. Cerium phosphate-based inhibitor for smart corrosion protection of WE43 magnesium alloy10.1016/j.electacta.2020.137368 ↗
10. Corrosion and mechanical performance of double-layered nano-Al/PCL coating on Mg–Ca–Bi alloy10.1016/j.vacuum.2015.04.039 ↗
11. Enhancement of corrosion resistance and mechanical properties of Mg–1.2Ca–2Bi via a hybrid silicon-biopolymer coating system10.1016/j.surfcoat.2015.09.039 ↗
12. Fabrication, degradation behavior and cytotoxicity of nanostructured hardystonite and titania/hardystonite coatings on Mg alloys10.1016/j.vacuum.2016.03.021 ↗
13. Investigation of Corrosion Protection Performance of Multiphase PEO (Mg2SiO4, MgO, MgAl2O4) Coatings on Mg Alloy Formed in Aluminate-Silicate- based Mixture Electrolyte10.1134/S2070205118030231 ↗
14. An analysis of the cold spray process and its coatings10.1361/105996302770348682 ↗
15. Gas-dynamic spraying. An experimental study of the spraying process10.1007/BF02468100 ↗
16. Supersonic particle deposition as an additive technology: methods, challenges, and applications10.1007/s00170-019-04682-2 ↗
17. Enhanced corrosion resistance and surface bioactivity of AZ31B Mg alloy by high pressure cold sprayed monolayer Ti and bilayer Ta/Ti coatings in simulated body fluid10.1016/j.matchemphys.2020.123627 ↗
18. Microstructural, mechanical properties and corrosion behavior of plasma sprayed NiCrAlY/nano-YSZ duplex coating on Mg–1.2Ca–3Zn alloy10.1016/j.ceramint.2015.08.025 ↗
19. Microstructural characterisation of air plasma sprayed nanostructure ceramic coatings on Mg–1%Ca alloys (bonded by NiCoCrAlYTa alloy)10.1016/j.ceramint.2015.08.118 ↗
20. Effect of Y2O3 stabilized ZrO2 coating with tri-model structure on bi-layered thermally grown oxide evolution in nano thermal barrier coating systems at elevated temperatures10.1016/S1002-0721(14)60034-X ↗
21. Surface modification of magnesium alloys using thermal and solid-state cold spray processes: Challenges and latest progresses10.1016/j.jma.2022.07.012 ↗
22. Microstructural evaluation and thermal oxidation behaviors of YSZ/NiCoCrAlYTa coatings deposited by different thermal techniques10.1016/j.ceramint.2020.06.001 ↗
23. Development of a generalized parameter window for cold spray deposition10.1016/j.actamat.2005.10.005 ↗
24. Processing parameters affecting cold spay coatings performances10.1007/s00170-013-5465-0 ↗
25. Recent trends in cold spray technology: looking at the future10.1179/026708410X12687356948715 ↗
26. The effect of pure aluminum cold spray coating on corrosion and corrosion fatigue of magnesium (3% Al-1% Zn) extrusion10.1016/j.surfcoat.2016.11.014 ↗
27. Study of Al alloy corrosion in neutral NaCl by the pitting scan technique10.1016/j.matchemphys.2010.02.022 ↗
28. Review of relationship between particle deformation, coating microstructure, and properties in high-pressure cold spray10.1007/s11666-017-0575-0 ↗
29. Enhanced corrosion resistance of cold-sprayed and shot-peened aluminum coatings on LA43M magnesium alloy10.1016/j.surfcoat.2020.125865 ↗
30. Enhancing anti-wear and anti-corrosion performance of cold spraying aluminum coating by high current pulsed electron beam irradiation10.1016/j.vacuum.2020.109772 ↗
31. K. Champagne, The Cold Spray Materials Deposition Process, (2007). doi: 10.1533/9781845693787.10.1533/9781845693787 ↗
32. Mechanical and corrosion properties in 3.5% NaCl solution of cold sprayed Al-based coatings10.1016/j.surfcoat.2020.125372 ↗
33. Optimization of in-situ shot-peening-assisted cold spraying parameters for full corrosion protection of Mg alloy by fully dense al-based alloy coating10.1007/s11666-016-0492-7 ↗
34. Improved corrosion protection of magnesium alloys AZ31B and AZ91 by cold-sprayed aluminum coatings10.1007/s11666-020-01128-0 ↗
35. Deposition of fully dense Al-based coatings via in-situ micro-forging assisted cold spray for excellent corrosion protection of AZ31B magnesium alloy10.1016/j.jallcom.2019.07.279 ↗
36. Corrosion resistant nickel coating with strong adhesion on AZ31B magnesium alloy prepared by an in-situ shot-peening-assisted cold spray10.1016/j.corsci.2018.04.018 ↗
37. Microstructure and mechanical property of Ti and Ti6Al4V prepared by an in-situ shot peening assisted cold spraying10.1016/j.matdes.2015.07.015 ↗
38. A hybrid approach to improve microstructure and mechanical properties of cold spray additively manufactured A380 aluminum composites
39. Releasing kinetics of dissolved copper and antifouling mechanism of cold sprayed copper composite coatings for submarine screen doors of ships10.1016/j.jallcom.2018.05.355 ↗
40. Aaron T. Nardi, Tahany Ibrahim El-Wardany, William Werkheiser, Michael A. Klecka, Method for Enhancing Bond Strength through In-situ Peening, US9938624B2, (2018).
41. Solid-state additive manufacturing high performance aluminum alloy 6061 enabled by an in-situ micro-forging assisted cold spray
42. Deposition behavior, microstructure and mechanical properties of an in-situ micro-forging assisted cold spray enabled additively manufactured Inconel 718 alloy10.1016/j.matdes.2018.06.024 ↗
43. Strengthened peening effect on metallurgical bonding formation in cold spray additive manufacturing10.1007/s11666-019-00854-4 ↗
44. New insights into the in-process densification mechanism of cold spray Al coatings: low deposition efficiency induced densification10.1016/j.jmst.2018.09.045 ↗
45. High velocity impact induced microstructure evolution during deposition of cold spray coatings: a review10.1016/j.surfcoat.2014.06.006 ↗
46. A new strategy for strengthening additively manufactured cold spray deposits through in-process densification
47. X-ray diffraction (XRD) techniques for materials characterization
48. Particle flattening during cold spray: mechanistic regimes revealed by single particle impact tests10.1016/j.surfcoat.2020.126386 ↗
49. Effect of Gas Propellant Temperature on the Microstructure, Friction, and Wear Resistance of High-Pressure Cold Sprayed Zr702 Coatings on Al6061 Alloy10.3390/coatings12020263 ↗
50. Mechanical behavior and strengthening mechanisms in ultrafine grain precipitation-strengthened aluminum alloy10.1016/j.actamat.2013.09.042 ↗
51. The effect of a simple annealing heat treatment on the mechanical properties of cold-sprayed aluminum10.1361/105996306X108138 ↗
52. Microstructure, mechanical properties and corrosion performance of 7075 Al matrix ceramic particle reinforced composite coatings produced by the cold gas dynamic spraying process10.1016/j.surfcoat.2013.07.020 ↗
53. Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions10.1016/j.pmatsci.2013.09.002 ↗
54. Plastic deformation: role of recovery and recrystallization
55. Interfacial bonding and microstructural evolution of Al in kinetic spraying10.1007/s10853-012-6332-3 ↗
56. Thermal stability of aluminum cold rolled to large strain10.1007/s10853-008-2874-9 ↗
57. Anthony Rollett · 2004
58. Recovery kinetics of nanostructured aluminum: model and experiment10.1016/j.actamat.2008.07.038 ↗
59. Length changes and stress effects during recovery of deformed aluminum10.1016/0001-6160(82)90061-X ↗
60. Elevated-temperature deformation at forming rates of 10−2 to 102 s−110.1007/s11661-002-0096-3 ↗
61. Grain refinement in a single titanium powder particle impacted at high velocity10.1016/j.scriptamat.2008.06.020 ↗
62. 2 - Fundamentals of additive manufacturing of metallic components by cold spray technology
63. Microstructural refinement within a cold-sprayed copper particle10.1007/s11661-009-9882-5 ↗
64. Y.K. Wei, X.T. Luo, C.J. Li, Grain Refinement of Pure Al Coating via In-Situ Shot-Peening-Assisted Cold Spray, Paper No: itsc2018, p0233, 233–237; 5 pages, (2018). doi: 10.31399/asm.cp.itsc2018p0233.10.31399/asm.cp.itsc2018p0233 ↗
65. Deposition characteristics of titanium coating in cold spraying10.1016/S0257-8972(02)00919-2 ↗
66. Adhesion, tribological and corrosion properties of cold-sprayed CoCrMo and Ti6Al4V coatings on 6061-T651 Al alloy10.1016/j.surfcoat.2017.07.062 ↗
67. Mechanical behavior of Ti cold spray coatings determined by a multi-scale indentation method10.1016/j.msea.2011.09.083 ↗
68. Effect of severe shot peening on corrosion behavior of AZ31 and AZ91 magnesium alloys10.1016/j.jallcom.2018.08.141 ↗
69. Corrosion performance of laser post treated cold sprayed titanium coatings10.1007/s11666-011-9637-x ↗
70. Transition from intergranular to pitting corrosion in fine grained aluminum processed by equal channel angular pressing10.1016/j.corsci.2014.06.031 ↗
71. Corrosion behavior of commercial aluminum alloy processed by equal channel angular pressing
72. Effect of carrier gases on microstructural and electrochemical behavior of cold-sprayed 1100 aluminum coating10.1016/j.surfcoat.2004.06.028 ↗
73. The effect of grain size and grain boundary misorientation on the corrosion resistance of commercially pure aluminium10.1016/j.corsci.2018.11.035 ↗
74. Corrosion behavior of AA5083 produced by high-energy ball milling10.1016/j.jallcom.2020.158268 ↗
75. Using friction stir processing to augment corrosion resistance of cold sprayed AA2024/Al2O3 composite coatings10.1016/j.jallcom.2018.09.386 ↗
76. Effects of bond coat and top coat (including nano zones) structures on morphology and type of formed transient stage oxides at pre-heat treated nano NiCrAlY/nano ZrO2-8%Y2O3 interface during oxidation10.1016/S1002-0721(14)60516-0 ↗
77. The influence of current density on the morphology and corrosion properties of MAO coatings on AZ31B magnesium alloy10.1016/j.surfcoat.2016.01.040 ↗
78. Corrosion behavior of magnesium and its alloys using electrochemical techniques10.1016/S0378-7753(96)02456-1 ↗
79. Corrosion characterization of Mg–8Li alloy in NaCl solution10.1016/j.corsci.2009.03.011 ↗
80. Corrosion resistance of a self-healing micro-arc oxidation/polymethy ltrimethoxy silane composite coating on magnesium alloy AZ3110.1016/j.corsci.2017.01.025 ↗
81. Influence of aluminum enrichment in the near-surface region of commercial twin-roll cast AZ31 alloys on their corrosion behavior10.1016/j.corsci.2017.04.027 ↗
82. AC impedance spectroscopy study of the corrosion behavior of an AZ91 magnesium alloy in 0.1M sodium sulfate solution10.1016/j.electacta.2006.10.007 ↗
83. Corrosion-resistant metallic coatings for aluminum alloys by cold spray10.1016/j.corsci.2022.110720 ↗
84. Pitting of 2024 alloys prepared by spark plasma sintering using powders with different sizes
85. AN SKP and EIS study of microporous nickel-chromium coatings in copper containing electrolytes10.1016/j.electacta.2019.05.108 ↗
86. Duplex coating combining layered double hydroxide and 8-quinolinol layers on Mg alloy for corrosion protection10.1016/j.electacta.2018.07.113 ↗
87. Deposition of duplex MAO layer/nanostructured titanium dioxide composite coatings on Mg–1% Ca alloy using a combined technique of air plasma spraying and micro arc oxidation10.1016/j.jallcom.2015.07.200 ↗
88. Corrosion behavior of Mg–2.4Zn alloy micro-alloyed with Ag and Ca10.1016/j.corsci.2013.09.012 ↗
89. Corrosion characteristics of cold gas spray coatings of reinforced aluminum deposited onto carbon steel10.1016/j.corsci.2016.10.019 ↗
90. Effect of an Fe (II)-modified trivalent chromium conversion process on Cr (VI) formation during coating of AA 2024 alloy10.1016/j.elecom.2018.05.013 ↗
91. Improved corrosion behavior of electron beam melted Ti-6Al–4V alloy in phosphate buffered saline10.1016/j.corsci.2017.05.003 ↗
92. Corrosion, wear and tribo-corrosion performance of a thermally sprayed aluminum coating modified by plasma electrolytic oxidation technique for offshore submerged components protection10.1016/j.corsci.2018.08.001 ↗
93. Mechanical and corrosion properties in 3.5% NaCl solution of cold sprayed Al-based coatings10.1016/j.surfcoat.2020.125372 ↗
94. Technical note: concerning the conversion of the constant phase element parameter Y0 into a capacitance10.5006/1.3280607 ↗
95. Corrosion resistance of cold-sprayed Ta coatings in very aggressive conditions10.1016/j.surfcoat.2010.02.052 ↗
96. Fabrication and corrosion resistance of a hydrophobic micro-arc oxidation coating on AZ31 Mg alloy10.1016/j.corsci.2014.10.041 ↗
97. Microstructure and corrosion resistance of warm sprayed titanium coatings with polymer sealing for corrosion protection of AZ91E magnesium alloy10.1016/j.surfcoat.2019.02.023 ↗
98. Ni coatings for corrosion protection of Mg alloys prepared by an in-situ micro-forging assisted cold spray: effect of powder feedstock characteristics
99. SVET, SKP and EIS study of the corrosion behavior of high strength Al and Al–Li alloys used in aircraft fabrication10.1016/j.corsci.2014.03.001 ↗
100. Composite anticorrosion coatings for AZ91D magnesium alloy with molybdate conversion coating and silicon sol–gel coatings10.1016/j.porgcoat.2009.07.003 ↗