journal article·2015-05

High temperature fatigue: behaviour of three typical classes of structural materials

A. Pineau, S. D. Antolovich

Materials at High Temperatures· Volume 32· Issue 3
Publisher page

Abstract

The goals of this paper are: (i) to review the mechanisms of cyclic deformation, damage accumulation and crack propagation in three types of materials widely used in power generation industries, i.e. Cr–Mo steels, austenitic stainless steels and superalloys used in jet engine turbines (both Ni base and Fe–Ni base) when they are tested at elevated temperature; (ii) to relate these mechanisms to engineering applications; (iii) to review life prediction methodologies including thermomechanical fatigue (TMF); and (iv) to point out current and likely future trends in the development of more fatigue resistant materials and life prediction methods. The emphasis is laid on the creep–fatigue–oxidation behaviour of the two first classes of materials, i.e. 9–12% martensitic Cr steels and austenitic stainless steels. As the major issue for the design of components used in power generation industries is the extrapolation of short term laboratory data to much longer times, only physically based models for life prediction are examined. In Ni base superalloys, the emphasis is laid on the effect of oxidation on fatigue crack growth rate at elevated temperature and on their behaviour in TMF
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: High Temperature Alloys and Creep · Fatigue and fracture mechanics · Fire effects on concrete materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (82)

Show source-provided references
1. Fournier B · 2007
2. 10.1016/j.actamat.2005.11.00110.1016/j.actamat.2005.11.001 ↗
3. 10.1016/j.msea.2006.08.08610.1016/j.msea.2006.08.086 ↗
4. 10.1016/j.msea.2006.08.08710.1016/j.msea.2006.08.087 ↗
5. 10.1016/j.ijfatigue.2007.05.00710.1016/j.ijfatigue.2007.05.007 ↗
6. 10.1016/j.ijfatigue.2007.05.00810.1016/j.ijfatigue.2007.05.008 ↗
7. 10.1016/j.ijfatigue.2008.02.00610.1016/j.ijfatigue.2008.02.006 ↗
8. 10.1007/s11661-008-9686-z10.1007/s11661-008-9686-z ↗
9. 10.1007/s11661-008-9687-y10.1007/s11661-008-9687-y ↗
10. Levaillant C: ‘Approche métallographique de l’endommagement d’aciers inoxydables austénitiques sollicités en fatigue plastique ou en fluage: description et interprétation physique des interactions fatigue–fluage–oxydation’, PhD thesis, Université de Technologie de Compiègne, Compiègne, France, 1984.
11. Weiss J: ‘Endommagement en viscoplasticité cyclique sous chargement multiaxial à haute température d’un acier inoxydable austénitique’, PhD thesis, Ecole des Mines de Paris, Paris, France, 1992.
12. Argence D: ‘Endommagements de fatigue et de fluage sous chargement multiaxial appliqué à un acier inoxydable austénitique’, PhD thesis, Ecole des Mines de Paris, Paris, France, 1996.
13. 10.1016/0001-6160(89)90194-610.1016/0001-6160(89)90194-6 ↗
14. Gaffard V: ‘Experimental study and modelling of high temperature creep flow and damage behaviour of 9Cr–1Mo–NbV steels and weldments’, PhD thesis, Ecole des Mines de Paris, Paris, France, 2005.
15. Brachet JC: ‘Alliages martensitiques: effets de l’addition de l’azote, du niobium et du vanadium sur la microstructure, les transformations de phase et les propriétés mécaniques’, PhD thesis, Université de Paris-Sud, Orsay, Paris, France, 1991.
16. 10.1016/j.actamat.2011.03.01710.1016/j.actamat.2011.03.017 ↗
17. 10.1016/j.jnucmat.2007.03.02010.1016/j.jnucmat.2007.03.020 ↗
18. Fournier B, Salvi M, Caës C, Malaplate J, Dalle F, Sauzay M, de Carlan Y and Pineau A: ‘High temperature mechanical strength and microstructural stability of advanced 9–12% Cr steels and ODS steels’, Proc. Conf. ICF 12, Ottawa, Ontario, Canada, July 2009, NRC. 3234–3244.
19. 10.1016/j.jnucmat.2013.10.03010.1016/j.jnucmat.2013.10.030 ↗
20. 10.1016/j.jnucmat.2004.04.04510.1016/j.jnucmat.2004.04.045 ↗
21. 10.1007/BF0262838410.1007/BF02628384 ↗
22. 10.1115/1.322497910.1115/1.3224979 ↗
23. 10.1016/0921-5093(94)90959-810.1016/0921-5093(94)90959-8 ↗
24. 10.1115/1.315759910.1115/1.3157599 ↗
25. 10.1016/j.ijfatigue.2005.08.01110.1016/j.ijfatigue.2005.08.011 ↗
26. Alexandre F: ‘Aspects probabilistes et microstructuraux de l’amorçage des fissures de fatigue dans l’alliage In 718’, PhD thesis, Ecole des Mines de Paris, Paris, France, 2004.
27. 10.1016/j.scriptamat.2003.09.04310.1016/j.scriptamat.2003.09.043 ↗
28. 10.1080/1478643680822752410.1080/14786436808227524 ↗
29. Rezgui B: ‘Interaction fatigue–fluage. Effet d’un temps de maintien de traction sur la résistance à la fatigue oligocyclique à 600°C d’un acier Z2CND17-13 (AISI 316L)’, PhD thesis, Université Paris XI, Paris, France, 1982.
30. 10.1016/j.msea.2010.08.01010.1016/j.msea.2010.08.010 ↗
31. Yamaguchi K · Metall. Trans. A · 1980 · 11 · 1692
32. Argence D and Pineau A: ‘Predictive metallurgy applied to creep–fatigue damage of austenitic stainless steels’, in ‘Structural materials: engineering application through scientific insight of materials’, (ed. E. H. Hondros and M. McLean), 229–257; 1996, Cambridge, The University Press.
33. Jacquelin B: ‘Amorçage des fissures en fatigue oligocyclique sous chargement multiaxial’, PhD thesis, Ecole des Mines de Paris, Paris, France, 1983.
34. Hales R and Ainsworth RA: ‘Multiaxial creep–fatigue rules’, Proc. 11th Int. Conf. on ‘Structural mechanics in reactor technology’, Post Seminar 5, 8th Int. Sem. on ‘Inelastic analysis, fracture and prediction’, Tokyo, Japan, August 1991, Nippon MARC Co., Ltd, 125–138.
35. 10.1007/BF0264859910.1007/BF02648599 ↗
36. 10.1111/j.1460-2695.1981.tb01115.x10.1111/j.1460-2695.1981.tb01115.x ↗
37. Levaillant C, Grattier J, Mottot M and Pineau A: ‘Creep and creep–fatigue intergranular damage in austenitic stainless steels: discussion of the creep-dominated regime’, in ‘Low-cycle fatigue’, (ed. H. D. Solomonet al.), ASTM STP 942, 414–437; 1988, Philadelphia, PA, ASTM.10.1520/STP24495S ↗
38. 10.1111/j.1460-2695.1980.tb01383.x10.1111/j.1460-2695.1980.tb01383.x ↗
39. Skelton RP: ‘Damage factors during high temperature fatigue crack growth’, in ‘Behavior of defects at high temperatures’, (ed. R. A. Ainsworth and R. P. Skelton), 191–218; 1993, London, Mechanical Eng. Publications.
40. Yoshida M, Levaillant C and Pineau A: ‘Metallographic measurement of creep intergranular damage and creep strain, Influence of stress state on critical damage at failure in an austenitic stainless steel’, Proc. Int. Conf. on Creep, Tokyo, Japan, April 1986, SME, 327–332.
41. Yoshida M, Levaillant C, Piques R and Pineau A: ‘Quantitative study of intergranular damage in an austenitic stainless steel on smooth and notched bars’, in ‘High temperature fracture mechanics and mechanics’, (ed. P. Bensussan), 3–21; 1990, London, Mech. Eng. Publications.
42. 10.1111/j.1460-2695.2004.00732.x10.1111/j.1460-2695.2004.00732.x ↗
43. 10.1179/mht.2004.00710.1179/mht.2004.007 ↗
44. 10.1016/j.nucengdes.2005.05.00210.1016/j.nucengdes.2005.05.002 ↗
45. 10.1007/BF0264765910.1007/BF02647659 ↗
46. Pineau A and Antolovich S: ‘High temperature fatigue’, in ‘Fatigue of materials and structures’, (ed. C. Bathias and A. Pineau), 1–130; 2011, London, ISTE/John Wiley.10.1002/9781118616789.ch1 ↗
47. 10.1016/j.engfailanal.2009.01.01010.1016/j.engfailanal.2009.01.010 ↗
48. Rosenker MV: ‘Safety recommendation’, NTSB report on Los Angeles engine failure, safety recommendation, NTSB, Washington, DC, USA, 2006, 60-06, 60–64.
49. McClintock FA: ‘Fatigue crack propagation’, ASTM STP 415, 483–484; 1967, Philadelphia, PA, American Society for Testing and Materials.
50. McClintock FA: ‘On the plasticity of the growth of fatigue cracks’, in ‘Fracture of solids’, (ed. D. C. Drucker and J. J. Gilman), 65; 1963, New York, Interscience Publishers.
51. 10.1016/0025-5416(82)90129-X10.1016/0025-5416(82)90129-X ↗
52. 10.1016/0025-5416(82)90130-610.1016/0025-5416(82)90130-6 ↗
53. 10.1016/0013-7944(75)90020-X10.1016/0013-7944(75)90020-X ↗
54. Saxena A · Metall. Trans. A · 1976 · 6 · 180910.1007/BF02642311 ↗
55. Baïlon JP and Antolovich SD: ‘The effect of microstructure on fatigue crack propagation: a review of existing models and suggestions for further research’, in ‘Fatigue mechanisms: advances in quantitative measurement of physical damage’, (ed. J. Lankfordet al.), ASTM STP 811, 313–349; 1983, Philadelphia, PA, American Society of Testing Materials.10.1520/STP30563S ↗
56. Bowman RR: ‘Effect of melt spinning on the microstructure and mechanical properties of three nickel base superalloys’, MSc thesis, Georgia Tech, Atlanta, GA, USA, 1985.
57. Bowman RR: ‘The effect of microstructure on the fatigue crack growth resistance of nickel base superalloys’, PhD thesis, Georgia Tech, Atlanta, GA, USA, 1988.10.7449/1988/Superalloys_1988_565_574 ↗
58. Bowman RR and Antolovich SD: ‘The effect of microstructure on the fatigue crack growth resistance of nickel base superalloys’, in ‘Superalloys 1988’, (ed. D. N. Duhlet al.), 565–574; 1988, Warrendale, PA, AIME.10.7449/1988/Superalloys_1988_565_574 ↗
59. 10.1016/0921-5093(92)90107-C10.1016/0921-5093(92)90107-C ↗
60. 10.1016/j.actamat.2013.02.05010.1016/j.actamat.2013.02.050 ↗
61. 10.1016/S1359-6454(96)00192-910.1016/S1359-6454(96)00192-9 ↗
62. Chassaigne JC: ‘High temperature crack propagation in Ni-base superalloy N18 fabricated by p.m. study of the coupling of mechanical and environmental effects at the head of a crack’, PhD thesis, Ecole des Mines de Paris, Paris, France, 1997.
63. Ponnelle S: ‘Propagation des fissures par fatigue à haute temperature dans l’Inconel 718: effets de microstructure et de chargements complexes’, PhD thesis, Ecole des Mines de Paris, Paris, France, 2001.10.1051/jp4:2000439 ↗
64. 10.1016/0308-0161(94)90149-X10.1016/0308-0161(94)90149-X ↗
65. Ponnelle S, Brethes B and Pineau A: ‘Orientational effects and influence of delta phase on fatigue crack growth rates in a forged disc of Inconel 718 superalloy’, Proc. 5th Int. Special Emphasis Symp. on ‘Superalloys 718, 625, 706 and derivatives’, Pittsburgh, PA, USA, June 2001, TMS. 501–510.10.7449/2001/Superalloys_2001_501_510 ↗
66. S. Ponnelle, B. Brethes and A. Pineau: ‘High temperature fatigue crack growth rate in Inconel 718: dwell effect annihilations’, in ‘Temperature-fatigue interaction’, (eds. L. Rémy and J. Petit) 257–266, 2002, Elsevier Science Ltd, London UK.10.1016/S1566-1369(02)80082-6 ↗
67. 10.1016/j.msea.2005.08.20610.1016/j.msea.2005.08.206 ↗
68. 10.1016/S0921-5093(97)00753-310.1016/S0921-5093(97)00753-3 ↗
69. 10.4028/www.scientific.net/MSF.539-543.26210.4028/www.scientific.net/MSF.539-543.262 ↗
70. 10.1007/BF0266320810.1007/BF02663208 ↗
71. Amaro RL: ‘Thermomechanical fatigue crack formation in a single crystal Ni-base superalloy’, PhD thesis, Georgia Institute of Technology, Atlanta, GA, USA, 2010.
72. 10.1016/j.ijsolstr.2011.03.01110.1016/j.ijsolstr.2011.03.011 ↗
73. 10.1007/BF0264854510.1007/BF02648545 ↗
74. Antolovich SD and Jayaraman N: ‘The effect of microstructure on fatigue behavior of nickel base alloys’, in ‘Fatigue: environment and temperature effects’, (ed. J. J. Burke and V. Weiss), 119–144; 1983, New York, Plenum Press.10.1007/978-1-4899-1736-2_7 ↗
75. 10.1016/0025-5416(81)90040-910.1016/0025-5416(81)90040-9 ↗
76. 10.1016/0025-5416(84)90177-010.1016/0025-5416(84)90177-0 ↗
77. 10.1016/j.pmatsci.2013.06.00110.1016/j.pmatsci.2013.06.001 ↗
78. 10.1111/j.1460-2695.2011.01660.x10.1111/j.1460-2695.2011.01660.x ↗
79. Amaro RL · Mater. Perform. Charact. · 2014 · 3 · 110.1520/MPC20130049 ↗
80. 10.1115/1.192456010.1115/1.1924560 ↗
81. Fernandez-Zelaia P: ‘The effect of stress elevators in thermomechanical fatigue crack formation in nickel-base superalloys’, MSc thesis, Georgia Institute of Technology, Atlanta, GA, USA, 2012.
82. 10.1111/ffe.1216610.1111/ffe.12166 ↗