journal article·2021-09-03Open access

Effect of indentation depth in impression creep test: conversion relationships and correction functions

S. Li, D. Purdy, S.J. Brett, D. Deng, A. Shibli, W. Sun

Materials at High Temperatures· Volume 38· Issue 5

Abstract

The impression creep test method has been used extensively to determine the in-service creep properties of power plant components from a small volume of material. In the standardisation of the impression creep test, the determination of a maximum ‘allowable’ indentation depth is an important issue. This paper presents the results of finite element analyses obtained using a simplified method based on steady-state creep, for evaluating the variation of conversion factors with indentation depth. The results obtained show that the indentation depth has a significant influence on the conversion parameters and the steady-state creep deformation rate when the indentation depth is sufficiently large. On this basis, recommendation on practical application of these conversion relationships was made to the users, and empirical formulas were provided for the possible corrections of the conversion factors. The effect of plastic zone due to initial loading on the subsequent creep was found to be insignificant.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Fatigue and fracture mechanics · Mechanical stress and fatigue analysis · Mechanical Behavior of Composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Faculty of Engineering, University of Nottingham, Nottingham, UK

College of Materials Science & Engineering, Chongqing University, China

Electric Power Research Institute, Palo Alto, California, USA

ETD Consulting, Leatherhead, UK

References (26)

Show source-provided references
1. 10.1243/09576509JPE37710.1243/09576509JPE377 ↗
2. 10.1115/PVP2011-5732510.1115/PVP2011-57325 ↗
3. 10.1111/j.1475-1305.2008.00465.x10.1111/j.1475-1305.2008.00465.x ↗
4. 10.1016/0020-7403(93)90035-S10.1016/0020-7403(93)90035-S ↗
5. 10.1111/j.1475-1305.2001.tb01238.x10.1111/j.1475-1305.2001.tb01238.x ↗
6. Parker JD · ASME PVP · 1994 · 279 · 167
7. 10.1177/030932471246329910.1177/0309324712463299 ↗
8. 10.1243/03093247JSA50210.1243/03093247JSA502 ↗
9. 10.1177/030932471246882010.1177/0309324712468820 ↗
10. 10.1016/j.mechmat.2019.10317110.1016/j.mechmat.2019.103171 ↗
11. 10.1007/s11340-017-0296-910.1007/s11340-017-0296-9 ↗
12. 10.1115/1.402519210.1115/1.4025192 ↗
13. 10.1016/j.tafmec.2018.10.00810.1016/j.tafmec.2018.10.008 ↗
14. 10.1080/09506608.2017.133253810.1080/09506608.2017.1332538 ↗
15. 10.1179/174328007X16031710.1179/174328007X160317 ↗
16. Sun W · Proc Inst Mech Eng L · 2008 · 222 · 175
17. 10.1007/BF0055224110.1007/BF00552241 ↗
18. 10.1016/0025-5416(86)90395-210.1016/0025-5416(86)90395-2 ↗
19. Gibbs WS · 1990
20. 10.1016/0020-7403(95)00112-310.1016/0020-7403(95)00112-3 ↗
21. Hyde TH · 2009
22. 10.1080/09603409.2017.141033010.1080/09603409.2017.1410330 ↗
23. ICSWG: Project Plan for the CEN Workshop on The Standardisation of the Impression Creep Test (Draft), February 2021.
24. 10.1016/0020-7403(68)90007-610.1016/0020-7403(68)90007-6 ↗
25. 10.1016/j.ijpvp.2009.07.00110.1016/j.ijpvp.2009.07.001 ↗
26. 10.1016/j.jmps.2019.10377410.1016/j.jmps.2019.103774 ↗