journal article·1995-01

Laboratory erosion—corrosion testing of FBC heat exchanger materials—Influence of test parameters

Peeter Tarkpea, Ulf Engman, Mikael Olsson

Materials at High Temperatures· Volume 13· Issue 3
Publisher page

Abstract

A laboratory erosion—corrosion test rig to simulate the simultaneous, synergistic interaction between solid particle erosion and corrosion at elevated temperatures is presented. The test rig is based on a propane-fired erosion system where the erosive particles are fed by a rotary vane feeder to a combined nozzle and burner. The particle system is pressurized with air and the particles are accelerated through a steel nozzle.In the present work, the performance of this test rig has been evaluated by studying the wastage characteristics of a low-alloyed carbon steel and an austenitic stainless steel. The work focuses on erosion and corrosion which are relevant to some aspects of FBC wastage problems. The tests were performed using 180–360μm angular alumina particles at 60° angle of impingement, at low particle velocities 2.6–8.2m/s and in the temperature interval 20–600°C. The steels were tested both in a blank polished condition as well as in a preoxidized condition.The erosion—corrosion rates of the steels were found to increase with increasing particle velocity. In contrast, the wastage rates were relatively independent of temperature in the temperature range investigated, the only exception being specimens of the low-alloyed steel exposed to the lowest particle velocity (2.6 m/s) which exhibited a drastic increase in wastage due to extensive spalling at the very highest temperature, i.e. 600°C. Specimens of the low-alloyed steel preoxidized at 700°C exhibited a somewhat higher erosion rate compared with non-preoxidized specimens and specimens preoxidized at 500°C.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Erosion and Abrasive Machining · High-Temperature Coating Behaviors · Particle Dynamics in Fluid Flows

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. Kang C. T. · Metallurgical Transactions · 1987 · 18
2. Kang C. T. · 1986 · 61
3. Rishel D. M. · 1990
4. Hogmark, S., Hammarsten, Å. and Söderberg, S. in‘Proc. of 6th International Conference on Erosion by Liquid and Solid Impact’, (Eds J. E. Field and N. S. Corney), Cambridge University Press, Cambridge, UK, 1983, paper 37
5. Sundararajan G. · 1990
6. 10.1016/0043-1648(91)90135-H10.1016/0043-1648(91)90135-H ↗
7. 10.1016/0043-1648(93)90070-310.1016/0043-1648(93)90070-3 ↗
8. 10.1016/0043-1648(75)90154-410.1016/0043-1648(75)90154-4 ↗
9. Raask, E. ‘Erosion Wear in Coal Utilization’, Springer-Verlag, Berlin, 1988
10. 10.1016/0043-1648(81)90062-410.1016/0043-1648(81)90062-4 ↗
11. 10.1016/0043-1648(87)90146-310.1016/0043-1648(87)90146-3 ↗
12. Sethi V. K. · 1986 · 329
13. 10.1016/0043-1648(92)90306-S10.1016/0043-1648(92)90306-S ↗
14. Rademakers, P. L. F., Lloyd, D. M. and Regis, V. in‘Proc. of Conference on High Temperature Materials for Power Engineering 1990’, (Eds E. Bachelet et al.), Liège, Belgium, 1990, p. 43
15. Stringer J. · 1993 · 3 · 797
16. 10.1016/0301-679X(95)92700-F10.1016/0301-679X(95)92700-F ↗
17. 10.1016/0043-1648(88)90210-410.1016/0043-1648(88)90210-4 ↗
18. Hutchings, I. M. and Wang, A. in‘Proc. of the Int. Conf. on New Materials and their Applications’, University of Warwick, 1990, p. 9
19. Holtzer, G. J. and Rademakers, P. L. F. in‘Proc. of the 1991 International Conference on Fluidized Bed Combustion’, (Ed. E. J. A. Canmet) ASME, Montreal, Canada, 1991, p. 743
20. 10.1016/0921-5093(89)90822-810.1016/0921-5093(89)90822-8 ↗
21. Sethi, V. K. and Corey, R. G. in‘Proc. of 7th International Conference on Erosion by Liquid and Solid Impact’, (Eds J. E. Field and J. P. Dear), Cambridge University Press, Cambridge, England, 1987, paper 73
22. Wang, B. Q., Geng, G. Q. and Levy, A. V. in‘Proc. of Int. Conf. on Wear of Materials’, (Eds K. C. Ludema and R. G. Bayer), ASME, Orlando, FL, USA 1991, p. 703
23. 10.5006/1.329921010.5006/1.3299210 ↗
24. 10.5006/1.358510510.5006/1.3585105 ↗
25. Hutchings I. M. · 1990
26. 10.1016/0043-1648(92)90159-610.1016/0043-1648(92)90159-6 ↗