Investigation of transverse residual stresses in a thick pultruded composite using digital image correlation with hole drilling
Source abstract
Abstract
Process induced residual stresses are one of the main sources of defects such as (pre) mature matrix cracking during pultrusion of fiber reinforced polymer composite profiles. Recently, comprehensive process models have been developed to understand and describe the underlying mechanisms of the residual stresses in pultrusion processes. The predicted stresses however have not been validated with experimental measurements which are necessary to verify the implemented material models and assumptions in the process models. A hole drilling method with digital image correlation (DIC) is used in the present work to measure the transverse strain relaxation due to material removal in a pultruded thick composite profile (20 × 20 mm) made of unidirectional glass/polyester. The corresponding residual stress state is back calculated using the measured strains in a finite element based numerical model. The estimated level of transverse residual stress in the core of the profile was found to be 6.1 MPa in tension.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced machining processes and optimization · Advanced Surface Polishing Techniques · Mechanical Behavior of Composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (50)
Show source-provided references
1. Baran · 2015
2. Starr · 2000
3. Modeling of heat transfer and unsaturated flow in woven fiber reinforcements during direct injection-pultrusion process of thermoplastic composites10.1016/j.compositesa.2015.04.017 ↗
4. The effect of process parameters on ultraviolet cured out of die bent pultrusion process10.1016/j.compositesb.2015.11.027 ↗
5. A review on the mechanical modeling of composite manufacturing processes10.1007/s11831-016-9167-2 ↗
6. Mechanisms generating residual stresses and distortion during manufacture of polymer-matrix composite structures10.1016/j.compositesa.2005.05.019 ↗
7. Process induced residual stresses and distortions in pultrusion10.1016/j.compositesb.2013.03.031 ↗
8. Probabilistic thermo-chemical analysis of a pultruded composite rod
9. Investigation of process induced warpage for pultrusion of a rectangular hollow profile10.1016/j.compositesb.2014.07.032 ↗
10. Modelling the pultrusion process of an industrial L-shaped composite profile10.1016/j.compstruct.2014.07.018 ↗
11. The internal stress evaluation of pultruded blades for a darrieus wind turbine. Key engineering materials
12. Analysis of pultrusion process for thick glass/ polyester composites: transverse shear stress formations
13. Mechanical characterization of pultruded elements: fiber orientation influence vs web-flange junction local problem. Experimental and numerical tests10.1016/j.compositesb.2018.01.001 ↗
14. Modelling manufacturing deformations in corner sections made of composite materials10.1177/0021998313477896 ↗
15. An analytical model on through-thickness stresses and warpage of composite laminates due to tool-part interaction10.1016/j.compositesb.2016.01.016 ↗
16. Measurement of residual stresses in layered composites by compliance method10.1177/002199830003400703 ↗
17. Residual-stress measurement in orthotropic materials using the hole-drilling method10.1007/BF02325147 ↗
18. Simulation of central hole drilling process for measurement of residual stresses in isotropic, orthotropic, and laminated composite plates10.1177/0021998306063803 ↗
19. Measurement of assembly stress in composite structures using the deep-hole drilling technique10.1016/j.compstruct.2017.12.031 ↗
20. Measurement of residual stress in thick section composite laminates using the deep-hole method10.1016/j.ijmecsci.2005.06.011 ↗
21. Cross-sectional mapping of residual stresses by measuring the surface contour after a cut10.1115/1.1345526 ↗
22. Effect of curing stresses on the first ply-failure in composite laminates10.1177/002199837901300101 ↗
23. Measurement of residual stresses in thick composite cylinders by the radial-cut-cylinder-bending method10.1016/j.compstruct.2005.07.020 ↗
24. A novel method to measure residual stresses in unidirectional GFRP10.1016/j.compstruct.2008.04.015 ↗
25. ASTM E837 13a. Standard test method for determining residual stresses by the hole-drilling strain-gage method; 2013.
26. Measurement and relaxation of residual stress
27. Determination of residual stress in composite laminates using the incremental hole-drilling method10.1177/002199803031057 ↗
28. Residual stress analysis of orthotropic materials by the through-hole drilling method10.1007/s11340-006-9019-3 ↗
29. Determination of calibration factors of the hole drilling method for orthotropic composites using an exact solution10.1177/0021998307075443 ↗
30. Characterization of residual stresses in a thin-walled filament wound carbon/epoxy ring using incremental hole drilling method10.1016/j.compscitech.2014.01.008 ↗
31. Study of surface residual stress by three-dimensional displacement data at a single point in hole drilling method
32. Residual stress determination by Hole drilling combined with optical methods10.1007/s11340-009-9329-3 ↗
33. Full-field strain measurements at the micro-scale in fiber-reinforced composites using digital image correlation10.1016/j.compstruct.2015.12.020 ↗
34. Uncertainty analysis in composite material properties characterization using digital image correlation and finite element model updating10.1016/j.compstruct.2017.10.009 ↗
35. Strain rate dependent multiaxial characterization of long fiber reinforced plastic10.1016/j.compositesb.2017.12.031 ↗
36. A novel biaxial specimen for inducing residual stresses in thermoset polymers and fibre composite material10.1177/0021998314554120 ↗
37. The application of digital image correlation for measuring residual stress by incremental hole drilling10.4028/www.scientific.net/AMM.13-14.65 ↗
38. Measurement of structural stresses by hole-drilling and DIC10.1007/s11340-016-0247-x ↗
39. Axially symmetrical stresses measurement in the cylindrical tube using DIC with hole-drilling10.1016/j.optlaseng.2014.09.009 ↗
40. Residual stress measurement using hole drilling and integrated digital image correlation techniques10.1007/s11340-013-9814-6 ↗
41. Study on experimental characterization of carbon fiber reinforced polymer panel using digital image correlation: a sensitivity analysis10.1016/j.optlaseng.2014.04.019 ↗
42. Residual stress determination using hole drilling and 3D image correlation10.1007/s11340-006-5859-0 ↗
43. Material characterization of a polyester resin system for the pultrusion process10.1016/j.compositesb.2014.04.030 ↗
44. Process-induced stress and deformation in thick-section thermoset composite laminates10.1177/002199839202600502 ↗
45. Atlac 382 Technical Data Sheet. DSM Composite Resins; 2003.
46. Prediction of shape distortions part i. Fe-implementation of a path dependent constitutive model10.1016/j.compositesa.2004.02.005 ↗
47. Verification and validation of residual stresses in composite structures10.1016/j.compstruct.2018.04.017 ↗
48. Influence of the paint coating thickness in digital image correlation experiments
49. Analysis of the local fiber volume fraction variation in pultrusion process10.1063/1.5008016 ↗
50. Hole-drilling residual stress measurement with artifact correction using full-field DIC10.1007/s11340-012-9626-0 ↗